Manuale d’uso / di manutenzione del prodotto 09 170 080 del fabbricante Miele
Vai alla pagina of 68
Operating and Installation Instructions Wine Storage Unit KWT 1601 Vi KWT 1611 Vi To prevent accidents and appliance damage read these instructions before installation or use.
IMPORTANT SAFETY INSTRUCTIONS .................................4 Guide to the wine storage unit .......................................7 Before use .......................................................9 Before using for the first time ..............
Installation options .................................................3 7 Adjusting the door opening angle (optional accessory) ....................3 8 Dimensions ......................................................3 9 Installation .................
When using the appliance, follow basic safety precautions, including the following: Read all instructions before installation and use to prevent accidents and machine damage. This appliance is intended for residential use only. Use only as described in this Operating manual.
Installation This appliance is top-heavy and must be secured to prevent the possibility of tipping forward. Keep the door closed until the appliance is completely installed and secured per installation instructions. ~ This appliance must be installed and connected in compliance with the installation instructions.
~ Never use a steam cleaner to clean the appliance. Pressurized steam could damage electrical components and cause a short circuit. ~ Do not use any electrical equipment inside the appliance. Danger of injury. Disposal of your old appliance ~ Before disposing of an old appliance, first make the door latch or lock unusable.
a Circulation fans / Active charcoal filter b Wooden racks c Insulation panel to separate the upper and middle temperature zones d Bottle display rack e Control panel / Insulation panel to separate th.
Control panel a Access button b Upper temperature zone c Middle temperature zone d Lower temperature zone e Temperature display: Allows you to set the temperature ( X colder; Y warmer) and set the dur.
Before using for the first time ^ Clean the inside of the appliance and the accessories with a mild solution of warm water and liquid dish soap. Dry with a soft cloth. If the appliance was transported or laid horizontally for any reason, allow it to stand vertical for at least 8 hours before turning it on.
Using the settings This appliance is operated with the use of touch keys activated by a finger. – An available button will appear white. – A selected button will appear yellow.. ^ Touch the access button so it turns yellow. On the control panel you will now see the sensor buttons of the three temperature zones.
^ To de-select a temperature zone touch the sensor button for that particular zone so that it turns white, or select another sensor button. ^ To leave the settings menu, touch the access button " p " so it turns white. The last settings entered are stored.
Turning the button sound On/Off If you prefer the buttons to be silent when touched, the button sound can be turned off. ^ Touch the access button " p "s oi t turns yellow. ^ Touch the sensor button for any temperature zone so it turns yellow.
Turning off for longer periods of time If the appliance is not going to be used for an extended time (for example, during a vacation) some precautions should be taken.
The appliance is equipped with an alarm system, to ensure that the temperature does not rise unnoticed because of energy loss or an open door. The alarm system is always operational, it does not need to be turned on. Temperature alarm If the temperature becomes too warm, an alarm sounds, the "alarm" indicator turns red and flashes.
Wine will continue to mature depending on the surrounding conditions. The length of time which wine can be kept in good condition will therefore depend not only on the temperature but also on the air quality.
Temperatures can be independently set in all three zones. The unit comes factory pre-set for white wine, red wine, and wine storage. The temperatures can be changed as desired. ^ Select the temperature zone you would like to change the temperature in.
Insulation panels for thermal separation The unit has two fixed insulation panels, to divide the interior into the three different temperature zones. This allows you to store three different types of wine, such as red wine, white wine and champagne. The correct serving temperature is crucial for the taste and therefore your enjoyment of the wine.
Temperature unit (Fahrenheit/Celsius) The temperature can be displayed in degrees Fahrenheit (°F) or Celsius (°C). ^ Touch the access button " p "s oi t turns yellow. ^ Touch the sensor button for any temperature zone, so that it turns yellow.
Humidity In a conventional refrigerator, the humidity levels are too low for storing wines. High humidity levels (60 - 70 %) are very important for the storage of wine, so that the corks remain moist. Under low humidity, the corks dry out from the outside and can no longer seal the bottles properly.
^ While holding down the X button, press the access button " p " once. Keep holding the X button down until the following appears in the display (approx. 5 seconds). ^ Tap the X button until 0 appears in the display. ^ Touch the access button " p "t o confirm.
Storage tips – Always unpack bottles – do not store wine in crates or boxes. – Always lay bottles on their side for storage. This keeps the corks moist from the inside, preventing air from entering. – Store similar wine varieties beside each other on the same shelf, to avoid restacking and the need to disturbed other bottles.
Bottle display rack The display rack, allows you to display selected bottles so they can be seen even with the door closed. ^ Lay the wine bottles in the display rack, so that they touch the wooden guide-rail a . ^ To remove the display rack pull it up and out, then attach it to the rear position on the wooden rack b .
Display lighting The display lighting can be turned on if you wish the bottles to be lit up even when the door is closed. Turning on ^ Touch the access button " p "s oi t turns yellow. ^ Touch the "Display light" sensor button so that it turns yellow.
During normal operation, condensate and frost can form on the rear wall of the refrigerator and drawers. You do not need to remove this build-up, it will defrost and evaporate automatically with the heat generated by the appliance.
To reduce the risk of electrical shock, disconnect the appliance from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before maintenance. Never use cleaning agents containing abrasive substances such as sand, soda, acids, chlorides or chemical solvents.
Before cleaning ^ Use the main switch to turn the appliance off completely. The main switch is located on the right side underneath the control panel. ^ Unplug the power cord. ^ Remove any bottles from the appliance and store it in a cool place. ^ Take out any removable parts, e.
Changing the light bulbs Do not remove the light covers for the display lighting. Should the lighting covers be damaged or need to be removed due to damage, do not look directly or with an optical instrument at the lighting. Interior lighting : The lighting automatically switches off after the door has been open for approx.
With the aid of the following guide minor problems can be corrected without a ser - vice call. Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage and may void the warranty.
What if the alarm is ringing? Possible fault Solution The appliance door has been open for longer than 5 minutes. Close the door. What if the alarm is ringing and the "alarm" indicator is lit? The door is not closed. One of these conditions has caused the temperature in the appliance to become too warm.
The appliance is making noises. Issue Possible fault Solution Brrrrr... Humming noise made by the compressor. This noise can get louder for brief periods when the motor is switching on. These noises are not a fault. The noise of the compressor and the coolant circulating in the system is unavoidable.
In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting the Technical Service department, please quote the model and serial number of your appliance given on the data plate inside the appliance.
32.
Installation instructions Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. To prevent accidents and machine damage read these instructions before installation or use.
Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags, etc.
, In areas with a tropical climate (over 100°F/38°C and more than 70% air humidity) the wine cooler must only be operated in air conditioned locations. Otherwise the function of the machine cannot be guaranteed. Have the appliance installed by a qualified technician, according to the enclosed installation instructions.
Base A fully loaded appliance is very heavy. The load-bearing capacity of your floor must meet the following requirements: KWT 16x1 Vi ........7 0 4l b s (319 kg) To ensure that the appliance is installed securely and functions properly, the base must be flat, level and made of a hard, rigid material.
Installation options There are many different installation options. You are limited only by the design of the kitchen. The door hinge cannot be exchanged. Single column The appliance can be installed at any preferred location in the kitchen. However, be sure the door will open and close properly in the chosen location.
Installation with partition using the "Merging Kit" The minimum thickness of the partition is 5 / 8 " (16 mm). If there is a partition with a thickness from 5 / 8 " (16 mm) to 6 5 .
Door dimensions (open min. 90°) *The dimensions of the door fronts and handles will vary according to each individual kitchen. 3 / 8 " (10 mm) AB C KWT 16X1 Vi 26 5 / 8 " (677 mm) Door front max. 1 1 / 2 " (38 mm)* Door handle* Door dimensions (open min.
Niche dimensions Dimensions 40.
Power supply 1. Power supply A KWT 16X1 Vi 12" (305 mm) Door front dimensions Dimensions 41.
Before you begin Read these instructions completely and carefully. Have the appliance installed by a qualified technician, according to the enclosed installation instructions. To reduce the risk of injury or damage to the product, two people should be used for installation.
Aligning the housing unit The housing unit must be carefully aligned using a spirit level before installing the appliance. The unit corners must be at right angles, as otherwise the furniture door will not align correctly with the 4 corners of the appliance.
^ Do not remove the installation supports from the appliance doors. They will be used later in the installation niche. There are transportation safety devices inside the appliance to protect the shelves until installation is complete. Do not remove them , or parts may be damaged.
^ Push the module into the slot until it locks into place. ^ Connect the appliance to the power supply and turn it on. After several seconds the indicator light e will come on. The indicator light will display different colors one after the other; any control light at the end indicates that the module was correctly installed.
Home Security System (HSS) If desired, the wine storage unit can be connected to the security system of your house, via a switching contact. If connected, you will be immediately informed of rising temperatures in the wine cooler. The Home security system connection must be hooked up before the unit is installed.
Preparing the installation niche , Keep the appliance door closed until it is securely fastened in the niche. Tipping hazard. Because of the size and weight of the appliance, it is essential to ensure that the appliance cannot tip over once it has been mounted in the niche.
^ Mark the holes through the anti-tip brackets b on the floor of the installation niche. ^ Set the brackets aside. Screws are supplied with the appliance for various applications/materials. If the anti-tip brackets cannot be attached securely with the screws supplied, an alternative anti-tip device can be used.
In a cabinet without a back wall screw the cabinet to the wall behind it in several places using suitable mounting brackets. For this, use suitable plugs/screws depending on the type of wall. Securing an alternative anti-tip device If the anti-tip brackets cannot be attached securely, an alternative anti-tip device can be used.
– The beam must cover the appliance by at least 2" (50.8 mm). ^ Mark the installation height (lower edge of the beam) on the rear wall of the niche. ^ Select screws according to the thickness of the wooden beam. Example: 3 ½" (89 mm) screw for 2x4 beam.
^ Plug the appliance into the power outlet b . The plug of the appliance should be easily accessible after installation. If the plug is not accessible after the appliance has been installed, disconnection from the power supply should be completed via the circuit breaker.
Important! When unscrewing the height-adjustable feet, proceed gradually, alternating between left and right. ^ Unscrew the height-adjustable feet until the mark on the base has reached the indicated guide dimension 1 1/4" (32 mm). The guide dimension of 1 1/4" (32 mm) is related to a niche height of 84" (2134 mm).
If there is no way to attach the top of the appliance, it can be attached to the sides of the installation niche. ^ Pull out the plate side lugs i . ^ Secure the attachment plate side lugs. If there is a fairly large gap above the appliance, cut a wooden beam to fit exactly and place it in the gap.
^ Open the appliance door. ^ Screw the attachment plate lugs m to the adjacent furniture/fixtures. With side-by-side combinations, only the external side of the appliances can be secured to the niche. Preparing the custom door ^ Open the appliance door.
^ Measure the distance X between the bracket and the overhead furniture/fixtures. ^ Loosen the two nuts. Set aside the nuts - you will need them again later. ^ With the inside facing up, lay the custom door on a stable surface (to avoid scratch marks, place some plastic or a cloth on the surface).
Attaching and aligning the custom door front ^ Open the door and hang the custom door with the mounting frame over the threaded bolts p . ^ Put the side strips o back into place and screw them completely down on both sides of the appliance door. Bag E contains spare screws for this purpose.
Attaching the covers ^ To mount the cover strips on both sides of the door, click them into place from bottom to top, into the gap between the appliance door and the custom door. ^ Screw the brackets onto both sides of the appliance, to hold the cover strip.
Attaching the toe-kick cover The maximum height of the toe-kick cover is 4" (102 mm) from the top of the floor. Do not cover ventilation slits in the plinth. Risk of damage to the appliance. ^ If required, cut the toe-kick cover to the required length and height.
^ Cut the cover strips (long for the sides of the door) to the required length X . ^ Push the cover strips on the into the gap between the furniture door and glass pane. ^ Cut the cover strips (short for the top and bottom of the door) to the required length Y .
^ Position the air separator in the center of the appliance door. ^ From below, screw the air separator firmly onto the door with the 2 screws. Installation 60.
, Avoid the risk of electrical shock - Plug into a grounded 3-prong outlet. - Do not move the ground plug. - Do not use an adapter. - Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Improper connection of the equipment grounding conductor may result in electric shock.
Miele's RemoteVision Wi-Fi technology creates a 'virtual link' between your appliance and our monitoring center. If a fault occurs, Miele's client service center will be notified and contact you, or another trusted individual identified on your call roster, in order to gain access to your appliance to fix the problem.
Accessing the RemoteVision control panel ^ Touch the access button " p "s oi t turns yellow. ^ Touch the sensor button for any temperature zone so it turns yellow. ^ Note the position of the X button, but do not touch. ^ Touch the access button " p " again so it turns white.
MasterCool control panel options for RemoteVision Status indicators Description of function Flashing ; ~ Module booting phase Flashing ; ‡ Not connected to network Flashing ; | Connection to network.
65.
66.
67.
Alteration rights reserved / 4911 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Miele 09 170 080 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Miele 09 170 080 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Miele 09 170 080 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Miele 09 170 080 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Miele 09 170 080, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Miele 09 170 080.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Miele 09 170 080. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Miele 09 170 080 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
