Manuale d’uso / di manutenzione del prodotto R111-16 del fabbricante METRObility Optical Systems
Vai alla pagina of 16
Installation & User Guide Models: R1 1 1-12 / R1 1 1-13 / R1 1 1-15 / R1 1 1-16 / R1 1 1-18 / R1 1 1-1T R ADIANCE 10M BPS S INGLE I NTERF ACE L INE C ARDS PWR LK LK AT TP AT 10BASE PWR LK AT COL 1.
This publication is protected by the copyright laws of the United States and other countries, with all rights reserved. No part of this publication may be reproduced, stored in a retrieval system, tra.
T able of Contents Radiance 10Mbps Single Interface Line Cards Installation & User Guide Overview ............................................................................................................... 4 Installation Guide ................
4 Overview The Radiance 10Mbps single interface line cards offer transpar ent integration of fiber optic connectivity or copper-to-coaxial integration in Ethernet networks. These innovative solutions provide full signal restoration— with low bit delay—ensuring accurate data transmission and guaranteeing maximum cable length support.
Radiance 10Mbps Single Interface Line Cards 5 Installation Guide Follow the simple steps outlined in this section to install and start using your Radiance 10Mbps single interface line card. NOTE: Electr ostatic dischar ge pr ecautions should be taken when handling any line car d.
6 Installation Guide R1 1 1-12 Only On the RJ-45 to BNC line card, a jumper is used to set either internal or external termination of the BNC port. See the diagram below to locate the jumper , labeled JP1. • Connect pins 1 and 2 to enable internal 50 Ω termination.
Radiance 10Mbps Single Interface Line Cards 7 3 Set the MDI-II/MDI-X Switch (twisted-pair ports only) T o eliminate the need for crossover cables, the Radiance line cards have an MDI- II to MDI- X slide switch for each twisted-pair port.
8 Installation Guide 4 • Grasp the card by the front panel as shown. • Insert the line card into a slot on the chassis making sure that the top and bottom edges of the board are aligned with the top and bottom card guides in the chassis. Do not force the board into the chassis unnecessarily .
Radiance 10Mbps Single Interface Line Cards 9 LK AT FL PWR AT LK 10 BASE RX LK TX FX M M II x PWR 100 FD RX LK T X TX 10/100 RX LK TX FX M M II x PWR 100 FD RX LK T X TX 10/100 LK AT FL R X PWR FD RX .
10 User Guide User Guide This section contains information about the operating features of the Radiance 10Mbps single interface line cards. LED Indicators The Radiance 10Mbps single interface line cards provide several LEDs for the visible verification of unit status and proper functionality .
Radiance 10Mbps Single Interface Line Cards 11 Link Loss Carry Forward (LLCF) * The Radiance 10Mbps single interface line cards incorporate an LLCF function for troubleshooting a remote connection. When LLCF is enabled, the FL and TP ports do not transmit a link signal until they receive a link signal from the opposite port.
12 User Guide T echnical Specifications Data Rate Data Rate ______________________ 10Mbps half duplex; 20Mbps full duplex Bit Delay __________________________________________________ < 5 bits Environmental Power ___________________________________ 5V @ 1.
Radiance 10Mbps Single Interface Line Cards 13 Multimode F/O Interface (R1 1 1-13, R1 11-15, R1 11-18) Connector __________________________________________ SC, ST or SMA W avelength _________________________________________________ 820nm RX Input Sensitivity ______________________________ -32.
14 User Guide Product Safety , EMC and Compliance Statements This equipment complies with the following requirements: •U L • CSA • EN60950 (safety) • FCC Part 15, Class A • EN55022 Class A (.
Radiance 10Mbps Single Interface Line Cards 15 W arranty and Servicing Three-Y ear W arranty for Radiance 10Mbps Single Interface Line Cards Metrobility Optical Systems, Inc.
Product Manuals The most recent version of this manual is available online at http://www .metrobility .com/support/manuals.htm Product Registration T o register your product, go to http://www .metrobility .com/support/registration.asp 25 Manchester Street, Merrimack, NH 03054 USA tel: 1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il METRObility Optical Systems R111-16 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del METRObility Optical Systems R111-16 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso METRObility Optical Systems R111-16 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul METRObility Optical Systems R111-16 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il METRObility Optical Systems R111-16, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del METRObility Optical Systems R111-16.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il METRObility Optical Systems R111-16. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo METRObility Optical Systems R111-16 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
