Manuale d’uso / di manutenzione del prodotto CLA (2014) del fabbricante Mercedes-Benz
Vai alla pagina of 354
CLA Operator's Manual Order no. 65155217 13 Part no. 1175841700 Edition D 2014 É11758417006ËÍ 1175841700 CLA-Class Operator's Manual.
Publication details Internet Further information about Mercedes-Benz vehicles and about Daimler AG can be found on the following websites: http://www.mbusa.
Welcome to the world of Mercedes-Benz We urge you to read this Operator's Manual carefully and familiarize yourself with the vehicle before driving. For you ro wn safety and a longer vehicle life, follow the instructions and warning notices in this manual.
.
Index ....................................................... 4 Introduction ......................................... 21 At ag lance ........................................... 27 Safety ................................................... 37 Opening and closing .
1, 2, 3 ... 12 Vs ocket see Sockets 4ETS see ETS/4ETS (Electronic Tractio nS ystem) 4MATIC (permanent all-wheel drive) Displa ym essage ............................ 238 4MATIC (permanent four-wheel drive) ..............................................
Audio system see separate operating instructions Authorized Centers see Qualified specialist workshop Authorized Mercedes-Benz Center see Qualified specialist workshop Authorized workshops see Qualified specialist workshop AUTO lights Display message .
C Calling up a malfunction see Display messages Car see Vehicle Care Carpet s. ......................................... 291 Car wash ........................................ 285 Display ........................................... 290 Exhaus tp ipe ..
Switching the rea rw indow defroster on/off ............................ 130 Switching the ZONE function on/ off .................................................. 128 Cockpit Overview .......................................... 28 see Instrument cluster COLLISIO NP REVENTION ASSIST Activating/deactivating the distance warning function .
Safety systems .............................. 213 SmartKey ....................................... 240 Tires ............................................... 234 Vehicle ...................... .................... .2 36 Distance recorder ..............
Fuel ................................................ 157 Genera l. ......................................... 156 Hydroplaning ................................. 161 Icy road surfaces ........................... 161 Limited braking efficiency on salted road s.
Exterior mirrors Adjusting ......................................... 97 Dipping (automatic) ......................... 99 Folding in/ou t( automatically) ......... 98 Folding in/ou t( electrically) ............. 98 Folding in whe nl ocking (on-board computer) .
High-beam headlamps Changing bulbs .............................. 113 Display message ............................ 224 Switching on/off ........................... 106 Hill start assist .................................. 138 HOLD function Deactivating .
Switching the daytime running lamps on/of f( switch) .................... 105 Switching the exterio rl ighting delayed switch-off on/off (on- board computer ). ........................... 207 Switching the surround lighting on/off (on-board computer) .
N Navigation Menu (on-board computer) ............ 199 see separate operating instructions Notes on breaking-in an ew vehicle 136 O Occupant Classification System (OCS) Fault s. .............................................. 49 Operation .............
PARKTRONIC Deactivating/activating ................. 177 Driving system ............................... 175 Function/notes ............................. 175 Important safety notes .................. 175 Problem (malfunction) ................... 178 Range of the sensors .
Rolle rs unblind Opening/closing .............................. 87 Panorama roof with power tilt/ sliding panel ..................................... 87 Roof carrier ........................................ 259 Roof lining and carpets (cleaning guidelines) .
Problem (malfunction) ..................... 76 Starting the engine ........................ 138 SmartKey positions (ignition lock) .. 137 Snow chains ...................................... 315 Sockets Center console .............................. 263 Points to observe before use .
Tires/wheels ................................. 340 Vehicle data ................................... 351 TELEAID Call priority .................................... 268 Downloading destinations (COMAND) ..................................... 268 Downloading route s.
M+S tires ....................................... 314 Maximum loaded vehicle weight (definition) ..................................... 334 Maximum load on a tire (definition) 334 Maximum permissible tire pressure (definition) ....................... 334 Maximum tire loa d.
U Unlocking Emergenc yu nlocking ....................... 79 From inside the vehicle (central unlocking button) ............................. 78 V Vanity mirror (in the sun visor) ....... .2 62 Vehicle Correct use ......................................
Windshield wipers Display message ............................ 240 Problem (malfunction) ................... 117 Replacing the wiper blades ............ 116 Switching on/off ........................... 115 Winte rd riving Slippery roa ds urface s. ...
Protection of the environment General notes H Environmental note Daimler's declared policy is one of comprehensive environmental protection. The objectives are for the natural resources that form the basis of our existence on this planet to be used sparingly and in a manner that takes the requirements of both nature and humanity into account.
Have aftermarke ta ccessories installed at a qualified specialist workshop. You could jeopardize the operating safety of your vehicle if yo u use parts, tires and wheels as well as accessories relevant to safety which have not bee na pproved by Mercedes.
Maintenance The Service and Warranty Booklet describes all the necessary maintenance work which should be done at regular intervals. Always have the Service and Warranty Booklet with you when you bring the vehicle to an authorized Mercedes-Benz Center.
Operating safety Important safety notes G WARNING If you do not have the prescribed service/ maintenance work or any required repairs carried out, this can result in malfunctions or system failures.
including interference that may cause undesired operation of the device." Diagnostics connection The diagnostics connection is only intended for the connection of diagnostic equipmen ta t a qualified specialist workshop.
Custome rR elations Department Mercedes-Ben zC anada, Inc. 98 Vanderhoof Avenue Toronto, Ontario M4G 4C9 Reporting safety defects USA only: The following text is publis hed as required of manufacturers under Title 49, Code of U.S. Federal Regulations, Part 57 5p ursuan tt o the "National Traffic and Motor Vehicle Safety Act of 1966".
Dashboard ........................................... 28 Instrument cluster .............................. 29 Multifunction steering wheel ............. 31 Center console .................................... 32 Overhea dc ontrol panel ................
Dashboard Function Page : Steering wheel paddle shifters 147 ; Combination switch 106 = Instrument cluster 29 ? Horn A DIRECT SELECT lever 142 B PARKTRONIC warning display 175 C Overhead control panel.
Instrumen tc luster Displays and controls Function Page : Speedometer with segments 195 ; Multifunction display 196 = Tachometer 195 Function Page ? Coolant temperature 194 A Fuel gauge B Instrument c.
Warning and indicator lamps Function Page : L Low-beam headlamps 105 ; T Parking lamps 106 = K High-beam headlamps 106 ? ÷ ESP ® 244 A Electric parking brake (red) F (USA only) ! (Canada only) 247 B.
Multifunction steering wheel Function Page : Multifunction display 196 ; Audio/COMAND display; see the separate operating instructions = ? Switches on the Voice Control System; see the separate operat.
Center console Center console, upper section Function Page : Audio system/COMAND; see the separate operating instructions ; c Seat heating 95 = c PARKTRONIC 175 ? ¤ ECO start/stop function 139 Functi.
Center console, lower section Function Page : Ashtray 262 Cigarette lighter 262 Socket 263 Stowage compartment 254 ; Stowage compartment 254 Function Page = Cup holder 260 ? Stowage compartment 254 A .
Overhea dc ontrol panel Function Page : u Switches the rear compartment interior lighting on/off 110 ; p Switches the right- hand reading lamp on/off 110 = | Switches the front interio rl ighting/auto.
Door control panel Function Page : Opens the door 77 ; %& Unlocks/locks the vehicle 78 = r 45= Saves the seat and exterio rm irror settings 100 ? Adjusts the seats electrically 93 A 7 Z ö Adjust.
36.
Useful information .............................. 38 Panic alarm ...................... .................... 38 Occupant safety .................................. 38 Children in the vehicle ........................ 54 Driving safet ys ystems .........
Useful information i This Operator's Manual describes all models and all standard and optional equipment of your vehicle available at the time of publication of the Operator's Manual. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described.
R Emergency Tensioning Device for the front seat belts and the outer seat belts in the rear R Seat belt force limiter for the front seat belts and the outer seat belts in the rear SRS reduces the risk of vehicle occupants coming into contact with parts of the vehicle's interior in the event of an accident.
decisive role in the deployment of an air bag, nor do they provide an indication of air bag deployment. The vehicle may be deformed significantly, e.g. the hood or the fender, without an air bag being deployed. This is the case if only parts which are relatively easily deformed are affected and the rate of deceleration is not high.
R Improper repai rw ork on the SRS creates a risk of rendering the SRS inoperative or causing unintended air bag deployment. Work on the SRS must therefore only be performed by qualified technicians.
As the ai rb ag inflates with considerable speed and force, a proper seating position and correct positioning of the hands on the steering wheel will help to keep you at a safe distance from the air bag.
function for the vehicle occupants in the event of a crash. i After an ai rb ag has been deployed, have the vehicle towed to the neares tq ualified specialist workshop, eve ni fy our vehicle is ready to drive.
Driver's knee bag : deploys underneath the steering column and front-passenger knee bag ; underneath the glove box. They deploy together with the front ai rb ags. They are designed to operate together with the front air bags in frontal impacts if certain thresholds are exceeded.
additional protection to that provided by the seat belt. Side impac ta ir bags will not deploy in side impacts which do not exceed the system's prese td eployment thresholds for lateral acceleration/deceleration .Y ou will then be protected by the fastened seat belt.
the 45 indicator lamp will illuminate when the engine is started and remain illuminated, indicating tha tt he front- passenger front air bag is deactivated.
in a rear-facing child restraint on the rear seat. R If you install a rear-facing child restraint on the front-passenge rs eat, make sure the 45 indicator lamp is illuminated, indicating that the front-passenger fron ta ir bag is deactivated.
To be classified correctly, the fron tp assenger must sit: R with the seat belt fastened correctly R in a positio nt hat is as upright as possible with their back against the seat backrest R with their feet on the floor The OCS weight sensor reading is affected if the occupant's weight is transferred, e.
Problems with the Occupant Classification System Problem Possible causes/consequences and M Solutions The 45 indicator lamp illuminates and remains illuminated. The person on the front-passenger seat: R has the weight of a typical adult R has been determined by the system not to be a child The OCS is malfunctioning.
Seat belts Important safety notes G WARNING The seat belt does not offer the intended level of protection if the backrest is not in the upright position. When braking or in the event of an accident, you could slide underneath the seat belt and sustain abdomen or neck injuries, for example.
Adjust the sea tb elt so that the shoulder section is located as close as possible to the middle of the shoulder. It should not touch the neck .N ever pass the shoulder portion of the seat belt under your arm. For this purpose, you can adjust the height of the seat belt outlet.
X Adjust the seat and move the backrest to an almos tv ertical position ( Y page 90). X Pull the seat belt smoothly through belt sash guide : . X Without twisting it, guide the shoulder section of the seat belt across the middle of your shoulder and the lap section across your pelvis.
If the driver's seat belt is not fastened when the engine is started, an additional warning tone will sound. This warning tone stops after a maximum of six seconds or once the driver's seat belt is fastened.
direction during the initial stages of the impact. R if, in the event of a side impact, on the side opposite the impact the vehicle decelerates or accelerates rapidly in a lateral direction. R if, in certain situation sw here the vehicle rolls over, the system determines that it can provide additional protection.
recommend that you always place a child in a rear-facing child restraint in a backseat. R If you must install a rear-facing child restraint on the front passenger seat because circumstances require you to do so, make sure the 45 indicator lamp is illuminated, indicating that the front passenger front air bag is deactivated.
Children that are too large for a child restraint must travel in seats usin gn ormal seat belts. Position the shoulder belt across the chest and shoulder, not the face or neck .
in the installation instructions that are included with the child restraint system. Always read and follow the manufacturer's instructions when using an infant or child restraint system or booster seat. Observe the warning labels in the vehicle interior or on the infant or child restraint.
for an air bag deactivation system is installed on the front-passenger seat. R on vehicles with an air bag dea ctivation system on the front-passenger seat, if the 4 PASSENGER AIR BAG OFF indicator lamp is not lit.
rings : for two LATCH-type (ISOFIX) child restraint systems are installed on the left and right of the rear seats. Non-LATCH-type (ISOFIX) child seats may also be used and can be installed using the vehicle's seat bel ts ystem. Install the child seat according to the manufacturer's instructions.
Child-proof locks Important safety notes G WARNING If childre na re left unsupervise d in the vehicle, they could: R open the doors, thus endangering other people or road users.
Override feature for the rear side windows G WARNING When children ride on the vehicle's rear seats, activate the override switch. Otherwise, the children could be injured, e.g. by trapping themselves in the rear side window. X To activate/deactivate: press button : .
G WARNING If ABS is faulty, the wheels could lock when braking. The steerability and braking characteristics may be severely impaired. Additionally, further driving safety systems are deactivated. There is an increased danger of skidding and accidents.
Always pay careful attention to the traffic situatio na nd be ready to brake. The distance warning functio nc annot always clearly identify objects and comple xt raffic situations.
Assist may not intervene. There is a ris ko fa n accident. Always pay careful attention to the traffic situatio na nd be ready to brake. G WARNING Adaptive Brake Assist does not react: R to people or .
braking function. COLLISION PREVENTION ASSIST PLUS can help you to minimize the risk of a front-end collision with a vehicle ahead or reduce the effects of such a collision. If COLLISION PREVENTION ASSIST PLUS detects that ther ei s a risk of a collision, you will be warned visually and acoustically.
! When testing the electric parking brake on a braking dynamometer, switch off the ignition. Application of the brakes by ESP ® may otherwise destroy the brake system. ! Vehicles with 4MATIC: switch off the ignition when the electric parking brake is being tested on a brake dynamometer.
Only activate SPORT handling mode in the situations described in the following. G WARNING If you deactivate ESP ® , ESP ® no longer stabilizes the vehicle. There is an increased risk of skidding and an accident. Only deactivate ESP ® in the situations described in the following.
Characteristics when ESP ® is deactivated If ESP ® is deactivated and one or more wheels start to spin, the ÷ ESP ® warning lamp in the instrumen tc luster does not flash. In such situations, ESP ® will not stabilize the vehicle. If you deactivate ESP ® : R ESP ® no longer improves driving stability.
ESP ® trailer stabilization General information If your vehicle/trailer combinatio nb egins to swerve, ESP ® assists you in this situation. ESP ® slows the vehicle down by braking and limiting the engine output until the vehicle/ trailer combination has stabilized.
Theft deterrent locking system Immobilizer The immobilize rp revents you rv ehicle from being started without the correct SmartKey. X To activate: remove the SmartKey from the ignition lock. X To deactivate: switch on the ignition. When leaving the vehicle, always take the SmartKey with you and lock the vehicle.
Useful information .............................. 72 SmartKey ............................................. 72 Doors .............................. ...................... 77 Trunk .................................................... 80 Side windows ..
Useful information i This Operator's Manual describes all models and all standard and optional equipment of your vehicle available at the time of publication of the Operator's Manual. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described.
If you do not open the vehicle within approximately 40 seconds of unlocking: R the vehicle is locked again. R the theft deterrent locking system is armed again.
X Push release catch : in the direction of the arrow and at the same time remove mechanical key ; from the SmartKey. For further information about: R unlocking the driver's door ( Y page 79) R un.
X Repeatedly tap the SmartKey against your palm until battery = falls out. X Inser tt he new battery with the positive terminal facing upwards. Use a lint-free cloth to do so. X Make sure that the surface of the battery is free from lint, grease and all other forms of contamination.
Problems with the SmartKey Problem Possible causes/consequences and M Solutions You cannot lock or unlock the vehicle using the SmartKey. The SmartKey battery is discharged or nearly discharged. X Try again to lock/unlock the vehicle using the remote control function of the SmartKey.
Problem Possible causes/consequences and M Solutions The engine cannot be started using the SmartKey. The on-board voltage is too low. X Switch off non-essential consumers, e.g. seat heating or interior lighting, and try to start the engine again. If this does not work: X Check the starter battery and charge it if necessary ( Y page 299).
X To unlock a front door: pull door handle ; . Locking knob : pops up. The door is unlocked and can be opened. X To open a front door: pull door handle ; . X To unlock a rear door: pull up locking knob : . The door is unlocked and can be opened. X To open a rear door: pull door handle ; .
Automatic locking feature X To deactivate: press and hold button : for about five seconds until a tone sounds. X To activate: press and hold button ; for about five seconds until a tone sounds. i If you press one of th et wo buttons and do not hear a tone, the relevant setting has already been selected.
X Turn the mechanical key clockwise as far as it will go to position 1 . X Turn the mechanical key back and remove it. X Make sure that the doors and the trunk lid are locked. X Insert the mechanical key into the SmartKey. i If you lock the vehicle as described above, the fuel filler flap is not locked.
Closing X Pull down the trunk lid using handle : . X Let the trunk lid drop into the lock. X If necessary, loc kt he vehicle with the & button on the SmartKey. Opening automatically from outside Important safety notes G WARNING Combustion engines emit poisonous exhaust gases such as carbon monoxide.
Emergency release If the trunk lid can no longer be opened from outside the vehicle, use the emergency release on the inside of the trunk lid. ! The trunk lid swings upwards when opened. Therefore, make sure that there is sufficient clearance above the trunk lid.
take the SmartKey with you and lock the vehicle. Never leave children unsupervised in the vehicle. Side window reversing feature The side windows are equi pped with an automatic reversing feature. If a solid object blocks or restricts a si de window during the closing process, the side window opens again automatically.
Convenience opening You can ventilate the vehicle before you start driving .T o do this, the SmartKey is used to carry out the following functions simultaneously: R unlock the vehicle R open the side .
If the side window opens again slightly: X Immediately pull the corresponding switch on the door control panel until the side window is completely closed ( Y page 83). X Hold the switch for an additional second. X If the corresponding side window remains closed after the button has been released, the side window has been reset correctly.
the sweep of the sliding sunroo fw hilst the vehicle is in motion. If somebody becomes trapped, reduce speed immediately, paying attention to road and traffic conditions .T he sliding sunroof opens again to its original position. If the sliding sunroof is not completely raised, you can then raise it further with the switch.
X Turn the SmartKey to position 1 or 2 in the ignition lock. X Make sure that the roller sunblinds are open. X Press or pull the 3 switch in the corresponding direction. i If you press the 3 switch beyond the point of resistance, an automatic opening/ closing process is started in the corresponding direction .
X Turn the SmartKey to position 1 or 2 in the ignition lock. X Press or pull the 3 switch in the corresponding direction. i If you press the 3 switch beyond the point of resistance, an automatic opening/ closing process is started in the corresponding direction .
Useful information .............................. 90 Correct driver's seat position ............ 90 Seats .................................................... 91 Steering wheel .................................... 96 Mirrors .....................
Useful information i This Operator's Manual describes all models and all standard and optional equipment of your vehicle available at the time of publication of the Operator's Manual. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described.
The seat belt should: R fit snugly across your body R be routed across the middle of your shoulder R be routed in your pelvic area across the hip joints X Before starting off, adjust the rear-view mirror and the exterior mirrors ( Y page 97) in such a way that you have a good view of road and traffic conditions.
recommended for the size and weight of the child .F or additional information, see the "Children in the vehicle" section. Ac hild's risk of serious or fatal injuries is significantly increased if the child restraints are not properly secured in the vehicle and/ or the child is not properly secured in the child restraint.
Adjusting the seats electrically : Head restrain th eight 2 ; Seat cushion angle = Seat height ? Seat fore-and-aft adjustment A Backrest angle i You can store the seat settings using the memory function ( Y page 100).
With this function you can adjust the distance between the head restraint and the back of the seat occupant's head. X To adjust forwards: pull the head restraint forwards in the direction of the arrow until it engages. There are several notches. X To move backwards: press and hold release button : and push the head restraint backwards.
: To raise the backrest contour ; To soften the backrest contour = To lower the backrest contour ? To harden the backrest contour Switching the seat heating on/off Activating/deactivating G WARNING Repeatedly switching on the seat heating can cause the seat cushion and backrest pads to become very hot.
Problems with the seat heating Problem Possible causes/consequences and M Solutions The seat heating has switched off prematurely or cannot be switched on.
Adjusting the steering wheel G WARNING If the steering wheel is unlocked while the vehicle is in motion, it could change position unexpectedly. This could caus ey ou to lose control of the vehicle. There is a risk of an accident. Before starting off, make sure the steering wheel is locked.
X Turn the SmartKey to position 1 or 2 in the ignition lock ( Y page 137). X Press button : for the left-hand exterior mirror or button ; for the right-hand exterior mirror. The indicator lamp in the corresponding button lights up in red. The indicator lamp goes out again after some time.
click and then the mirrors engage in position. The mirror housing is engaged agai na nd you can adjus tt he exterior mirrors as usual ( Y page 97). Automatic anti-glare mirrors The "Automatic anti-glare mirrors" function is only available if the vehicle is equipped with the "Mirrors package".
X Press memory button M ? and one of the arrows on adjustment button = within three seconds. The parking position is stored if the exterior mirror does not move. X If the mirror moves out of position, repeat the steps. Calling up a stored parking position setting X Turn the SmartKey to position 2 in the ignition lock ( Y page 137).
Calling up as tore ds etting X Press and hold the relevant storage position button 1 , 2 or 3 until the seat and exterio rm irrors are in the stored position.
102.
Useful information ............................ 104 Exterior lighting ................................ 104 Interior lighting ................................. 110 Replacing bulbs ................................. 111 Windshield wipers ................
Useful information i This Operator's Manual describes all models and all standard and optional equipment of your vehicle available at the time of publication of the Operator's Manual. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described.
Automatic headlamp mode G WARNING When the ligh ts witc h is set to à , the low- beam headlamps may not be switched on automatically if there is fog, snow or other causes of poor visibility due to the weather conditions such as spray. There is a risk of an accident.
Rear fog lamp The rea rf og lamp improves visibility of your vehicle for the traffic behind in the event of thick fog. Please take note of the country- specific regulations for the use of rear fog lamps. X To switch on the rear fog lamps: turn the SmartKey in the ignition lock to position 2 or start the engine.
X Press the combination switch beyond the pressure point in the direction of arrow : . In the à position, the high-beam headlamps are only switched on when it is dark and the engine is running. The blue K indicator lamp in the instrument cluster lights up when the high- beam headlamps are switched on.
Active: R if you are driving at speeds below 25 mph (40 km/h) and switch on the tur ns ignal or tur nt he steering wheel. R if you are driving at speeds between 25 mph (4 0 km/h) and 45 mph (7 0 km/h) and turn the steering wheel.
system no longer detects any other vehicles, it reactivates the high-beam headlamps. The system's optical sensor is located behind the windshield near the overhead control panel. Switching Adaptive Highbeam Assist on/off X To activate: activate the Adaptive Highbeam Assist function using the on- board computer ( Y page 207).
Interior lighting Overview of interior lighting Front overhead control panel : p To switch the left-hand fron tr eading lamp on/off ; c To switch the front interior lighting on = v To switch the on/of.
Crash-responsive emergency lighting The interio rl ighting is activated automatically if the vehicle is involved in an accident. X To switch off the crash-responsive emergency lighting: press the hazard warning lamp button. or X Loc ka nd then unlock the vehicle using the key.
Halogen headlamps : Tur ns ignal lamp: PY 21 W ; Low-beam headlamp/daytime running lamp/parking lamp/standing lamp: H15 55 W/15 W = Low-beam headlamp: H7 55 W Vehicles with Intelligen tL ight System :.
X Remove the cover in the front wheel housing ( Y page 112). X Turn housing cover : counter-clockwise and pull it out. X Turn bulb holder ; counter-clockwise and pull it out. X Take the bulb out of bulb holder ; . X Inser tt he new bulb into bulb holder ; .
X Insert bulb holder ; into the lamp and turn it clockwise. X Align housing cover : and turn it clockwise until it engages. Changing the rear bulbs Opening and closing the side trim panels You must open the side trim panel in the trunk before you can change the bulbs in the tail lamps.
X Brake lamp/rear fog lamp/backup lamp: remove the corresponding bulb from the bulb holder. X Insert the new bulb into the bulb holder. X Turn signal lamp: lightly press the bulb into the bulb holder, turn it counter- clockwise and remove it from bulb holder.
Replacing the wiper blades Important safety notes G WARNING If the windshield wipers begin to move while you are changing the wiper blades, you could be trapped by the wiper arm .T here is a risk of injury. Always switch off the windshield wipers and ignition before changing the wiper blades.
Problems with the windshield wipers Problem Possible causes/consequences and M Solutions The windshield wipers are jammed. Leaves or snow, for example, may be obstructing the windshield wiper movement .T he wiper motor has been deactivated. X For safety reasons, you should remove the SmartKey from the ignition lock.
118.
Useful information ............................ 120 Overview of climate control sys- tems ................................................... 120 Operating the climate control sys- tems ................................................... 125 Setting the air vents .
Useful information i This Operator's Manual describes all models and all standard and optional equipment of your vehicle available at the time of publication of the Operator's Manual. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described.
Control panel for climate control USA only : Sets the temperature ( Y page 127) ; Defrosts the windshield ( Y page 129) = Sets the air distribution ( Y page 128) ? Activates/deactivates air-recirculat.
? Activates/deactivates air-recirculation mode ( Y page 131) A Sets the airflow ( Y page 128) B Switches cooling with ai rd ehumidification on/off ( Y page 125) C Switches the rear window defroster on.
Control panel for dual-zone automatic clim ate control USA only : Sets the temperature, left ( Y page 127) ; Sets climate control to automatic ( Y page 127) = Defrosts the windshield ( Y page 129) ? I.
Canada only : Sets the temperature, left ( Y page 127) ; Sets climate control to automatic ( Y page 127) = Defrosts the windshield ( Y page 129) ? Increases the airflow ( Y page 128) A Sets the air di.
R Only available on vehicles for Canada: use the residual heat function if you want to heat or ventilate the vehicle interior when the ignition is switched off. The residual heat function can only be activated or deactivated with the ignition switched off.
dehumidified according to the temperature selected. Condensation may drip from the underside of the vehicle when it is in cooling mode. This is normal and not a sign that there is a malfunction. Activating/deactivating X To activate: press the ¿ button.
Problems with the "Cooling with air dehumidification" function Problem Possible causes/consequences and M Solutions The indicator lamp in the ¿ button flashes three times or remains off. The "Cooling with air dehumidification" function cannot be switched on.
setting in small increments. Start at 72 ‡ (22 †). Setting the air distribution Automatic climate control Air distribution settings ¯ Directs air through the defroster vents P Directs air through the center and side air vents O Directs air through the footwell air vents i You can also activate several air distribution settings simultaneously.
Defrosting the windshield You can use this function to defrost the windshield or to defrost th ei nside of the windshield and the side wi ndows. i You should only select the "Windshield defrosting" functio nu ntil the windshield is clear again.
Dual-zone automatic climate control X Activate the ¿ "Cooling with air dehumidification" function. X Activate automatic mode à . X If the windows cont inue to fog up, activate the ¬ "Windshield defrosting" function. i You should only select this setting until the windshield is clear again.
Problems with the rear window defroster Problem Possible causes/consequences and M Solutions The rear window defroster has deactivated prematurely or cannot be activated. The battery has not been sufficiently charged. X Switch off any consumers that are not required, e.
X Turn the SmartKey to position 0 in the ignition lock or remove it ( Y page 137). X To activate: press the Ì button. The indicator lamp in the Ì button lights up.
Setting the rear-compartment air vents : Rear-compartment air vent, left ; Rear-compartment air vent, right = Rear-compartment air vent thumbwheel X To open/close: turn thumbwheel = up or down.
134.
Useful information ............................ 136 Notes on breaking-in an ew vehicle 136 Driving ............................................... 136 Automatic transmission ................... 142 Refueling ...........................................
Useful information i This Operator's Manual describes all models and all standard and optional equipment of your vehicle available at the time of publication of the Operator's Manual. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described.
G WARNING If you switch off the ignitio nw hile driving, safety-relevant functions are only available with limitations, or not at all. This could affect, for example, the power steering and the brake boosting effect .Y ou will require considerably more effort to steer and brake.
the engine compartment or in the exhaust system. ! Do not depress the accelera tor pedal when starting the engine. i During a cold start, the engine runs at highe rs peeds to enable the catalytic converter to reach its operating temperature. The sound of the engine may change during this time.
R the electric parking brake is applied. R ESP ® is malfunctioning. Furthe ri nformation on holding the vehicle stationary on uphill gradients ( Y pa ge 145). ECO start/sto pf unction Introduction The ECO start/stop function switches the engine off automatically if the vehi cle is stopped unde rc ertain conditions.
automatic engine switch-off is again possible. Vehicles with automatic transmission If the vehicle is braked to a standstill in D or N , the ECO start/stop function switches off the engine automatically. i The HOLD function can be activated if the engine has been switched off automatically.
Problems with the engine Problem Possible causes/consequences and M Solutions The engine does not start. The HOLD function or DISTRONIC PLUS is activated. X Deactivate the HOLD function ( Y page 172) or DISTRONIC PLUS ( Y page 164). X Try to start the engine again.
Problem Possible causes/consequences and M Solutions The engine is not running smoothly and is misfiring. There is a malfunction in the engine electronics or in a mechanical component of the engine management system. X Only depress the accelerator pedal slightly.
in the transmission position display ( Y page 143) in the multifunction display. Transmission position and drive program display The current transmission position and drive program appear in the multifunction display.
Shifting to neutral N X When the vehicle is stationary, depress the brake pedal. X Push the DIRECT SELECT lever up or down to the first point of resistance. If the engine has been switched off, the automatic transmission automatically shifts to N . Remaining in neutral N If the automatic transmission is to remain in neutral N , e.
Engaging park position P X When the vehicle is stationary, press P button : . Transmission positions B Par kp osition Do not shift the transmission into position P unless the vehicle is stationary ( Y page 153). The parking lock should not be used as a brake when parking .
The clutch may overheat if you hold the vehicle stationary on uphill gradients by depressing the accelerator pedal. If the clutch overheats, a warning tone sounds. All vehicles (except AMG vehicles): the Stop Vehicle Shift to P Leave Engine Running display message appears in the multifunction display .
AMG vehicles C Controlled Efficiency Comfortable, economical driving S Sport Sporty driving style M Manual Manual gear shifting Only change from automatic drive program C or S to manual drive program M when the vehicle is stationary.
R the vehicle pulling away mor eg ently in forward and reverse gears, unless the accelerator pedal is depressed fully R increased sensitivity. This improves driving stability on slippery road surfaces, for example R the automatic transmission shifting up sooner .
Upshifting X Pull the right-hand steering wheel paddle shifter ( Y page 147). The automatic transmission shifts up to the next gear. i All vehicles (except AMG vehicles): in order to preven te ngine d.
reached. This prevents the engine from overrevving. Switching off the manual drive program X Press the progra ms electo rb utton ( Y page 146) repeatedly until E or S appears in the multifunction display.
Problems with the transmission Problem Possible causes/consequences and M Solutions The transmission has problems shifting gear. The transmission is losing oil. X Have the transmission checked at a qualified specialist workshop immediately. The acceleration ability is deteriorating.
! Overfilling the fuel tank could damage the fuel system. ! Take care not to spill any fuel on painted surfaces. You could otherwise damage the paintwork. ! Use a filter when refueling from a fuel can. Otherwise, the fuel lines and/or injection system could be blocked by particles from the fuel can.
Problems with fuel and the fuel tank Problem Possible causes/consequences and M Solutions Fuel is leaking from the vehicle. The fuel line or the fuel tank is faulty. G WARNING Risk of explosion or fire. X Turn the SmartKey to position 0 in the ignition lock immediately and remove it ( Y page 137).
To ensure that the vehicle is secured against rolling away unintentionally: R the electric parking brake must be applied. R the transmission must be in position P and the transmission position display must show P . R the SmartKey must be removed from the ignition lock.
In addition, they may operate vehicle equipment and become trapped .T here is a risk of an accident and injury. When leaving the vehicle, always take the SmartKey with you and lock the vehicle.
If you rs eat belt is not fastened, the following conditions must be fulfilled to automatically release the electric parkin gb rake: R the driver's door is closed. R you have shifted out of transmission position P or you have previously driven faster than 2 mph (3 km/h).
Drive sensibly –s ave fuel Observe the following tips to save fuel: R The tires should always be inflated to the recommended tire pressure. R Remove unnecessary loads. R Remove roof racks whe nt hey are not needed. R Warm up the engine at low engine speeds.
Apart from driving style, cons umption is dependent on many factors such as, e.g.: R load R tire pressure R cold start R choice of route R electrical consumers switched on These factors are not take n into consideratio nb y the ECO display.
Heavy and light loads G WARNING If you rest you rf oot on the brake pedal while driving, the braking system can overheat. This increases the stopping distance and can even cause the braking system to fail. There is a risk of an accident. Never use the brake pedal as a footrest .
Have brake pads installed and brake fluid replaced at a qualified speciali st workshop. If the brake system has only bee ns ubjec tt o moderate loads, you should test the functionality of you rb rakes at regular intervals. You can find a description of Brake Assist (BAS) on ( Y page 62).
X Hold test gauge A vertically on brake disc : and slide measuring pin ; onto brake disc : . X Check which colo rf ield ? the arrow on measuring pin ; is pointing to. Green :t he brake pad/lining thickness is sufficient. Red :t he brake pad/lining thickness is not sufficient.
If the vehicle threatens to skid or cannot be stopped when moving at low speed: X Shift the transmission to position N . Drive particularly carefully on slippery road surfaces .A void sudden acceleration, steering and braking maneuvers. Do not use the cruise control or DISTRONIC PLUS.
Activation conditions To activate cruise control, all of the following activation conditions mus tb e fulfilled: R the electric parking brake must be released. R you are driving faster than 20 mph(30 km/h). R ESP ® must be active, but not intervening.
Deactivating cruise control There are several ways to deactivate cruise control: X Briefly press the cruise control lever forwards = . or X Brake. Cruise control is automatically deactivated if: R the.
G WARNING DISTRONIC PLUS cannot always clearly identify other road users and comple xt raffic situations. In such cases, DISTRONIC PLUS may: R give an unnecessary warning and then brake the vehicle R neither give a warning nor intervene R accelerate unexpectedly There is a risk of an accident.
Cruise control lever : To store the curren ts peed or a higher speed ; To store the curren ts peed or a lower speed = To deactivate DISTRONIC PLUS ? To store the curren ts peed or calling up the last .
X Briefly pull the cruise control lever ( Y page 166) towards you ? . X Remove your foot from the accelerator pedal. DISTRONIC PLUS is activated. The first time it is activated, the current speed is stored. Otherwise, it sets the vehicle cruise speed to the previously store dv alue.
R the battery is disconnected. R the accelerator pedal has been depressed, e.g .b y a vehicle occupant. There is a risk of an accident. If you wish to exit the vehicle, always tur no ff DISTRONIC PLUS and secure the vehicle against rolling away. For further information on deactivating DISTRONIC PLUS ( Y page 169).
see this distance in the multifunction display ( Y page 170). i Make sure that you maintain the minimum distance to the vehicle in front as required by law. Adjust the distance to the vehicle in front if necessary. X To increase: turn control = in direction ; .
DISTRONIC PLUS displays in the instrument cluster Displays in the speedometer Example: DISTRONIC PLU Sd isplays in the speedometer When DISTRONIC PLUS is activated, one or two segments ; in the set speed rang el ight up. If DISTRONIC PLUS detect sav ehicle in front, segments ; between speed of the vehicle in front = and stored speed : light up.
Cornering, going into and coming out of a bend The ability of DISTRONIC PLU St o detect vehicles when cornering is limited. Your vehicle may brake unexpectedly or late. Vehicles traveling on ad ifferent line DISTRONIC PLUS may not detect vehicles traveling on a different line.
Crossing vehicles DISTRONIC PLUS may detect vehicles that are crossing your lane by mistake. Activating DISTRONIC PLUS at traffic lights with crossing traffic, for example, could cause your vehicle to pull away unintentionally.
Activating the HOLD function Example: vehicles with a color multifunction display X Make sure that the activation conditions are met. X Depress the brake pedal. X Quickly depress the brake pedal further until : appears in the multifunction display. The HOLD function is activated.
Activating RACE START X Depress the brake pedal wit hy our left foot and keep it depressed. X Pull and hold both steering wheel shift paddles. X The RACE START Confirm: Paddle UP Cancel: Paddle DOWN message appears in the multifunction display. X Release both steering wheel shift paddles.
PARKTRONIC Important safety notes PARKTRONIC is an electronic parking aid with ultrasonic sensors. It monitors the area around your vehicle using six sensors in the front bumper and six sensors in the rear bumper. PARKTRONIC indicates visually and audibly the distance between your vehicle and an object.
care not to scratch or damage them ( Y page 289). Front sensors Center Approx. 40in (approx. 100cm) Corners Approx. 24in (approx. 60cm) Rear sensors Center Approx. 48 in (approx. 120 cm) Corners Approx. 32in (approx. 80cm) Minimum distance Center Approx.
seconds. This indicates that you have now reached the minimum distance. Deactivating/activating PARKTRONIC : Indicator lamp ; To deactivate/activate PARKTRONIC If indicator lamp : lights up, PARKTRONIC is deactivated. i PARKTRONIC is automatically activated when you turn the SmartKey to position 2 in the ignition lock.
Problems with PARKTRONIC Problem Possible causes/consequences and M Solutions Only the red segments in the PARKTRONIC warning displays are lit. You also hear a warning tone for approximately two seconds. PARKTRONIC is then deactivated and the indicator lamp on the PARKTRONIC button lights up.
Parking tips: R On narrow roads, drive as close to the parking space as possible. R Parking spaces that are littered or overgrown might be identified or measured incorrectly. R Parking spaces that are partially occupied by trailer drawbars might not be identified as such or be measured incorrectly.
and measures parking spaces on both sides of the vehicle. Active Parking Assist will only detect parking spaces: R that are parallel or at right-angles to the direction of travel R that are parallel to the direction of travel and at least 59 in (1.5 m) wide R that are parallel to the direction of travel and at least 39.
message appears in the multifunction display. i You will achieve the best results by waiting for the steering procedure to complete before pulling away. X Drive forwards and be ready to brake at all times. X Stop as soon as PARKTRONIC sounds the continuous warning tone, if not before.
X Shift the transmissio nt o position D or R as required while the vehicle is stationary. Active Parking Assist immediately steers in the other direction .T he Park Assist Active Accelerate and Brake Observe Surroundings message appears in the multifunction display.
opens. Only once the maneuvering process has been completed and the rear view camera has switched off does the flap close again. For technical reasons, the flap may remain open briefly after the rear view camera has been deactivated. If you switch off the engine, the flap will also close.
Lanes : White guide line withou tt urning the steering wheel, vehicle width including the exterior mirrors (static) ; Yellow lane marking tires at current steering wheel angle, vehicle width to the ou.
Backing up straight into a parking space withou tt urning the steering wheel : White lane with steering wheel straight ; Yellow guide line at a distance of approximately 3 ft (1.0 m) from the rear of the vehicle = Red guide line at a distance of approximately 10 in (0.
Driving to the final position : White lane at current steering wheel angle ; Parking space marking X Turn the steering wheel to the center positio nw hile the vehicle is stationary.
intermittent warning ton et wice and the Attention Assist: Take a Break! message appears in the multifunction display. X If necessary, take a break. X Press the a or % button to confirm the message. On long journeys, take regular breaks in good time to allow yourself to rest properly.
information in the multifunction display is hidden for this period. : Speed Limit Assist is available and switched on ; Traffic sign indicating as peed limit or the end of a speed limit (example) = Ow.
FCC .D o not tamper with, alter, or use in any non-approved way. Any unauthorized modification to this device could void the user’s authority to operate the equipment.
20 mph (30km/h), then warning lamp : on the corresponding side lights up red. This warning is always emitted whe na vehicle enters the blind spot monitoring range from behind or from the side .W hen you overtake a vehicle, the warning only occurs if the difference in speed is less than 7m ph (12 km/h).
front, for vehicle speed, for braking in good time and for staying in you rl ane. The Lane Keeping Assist does no tk eep the vehicle in the lane. The system may be impaired or may not function if: R there is poor visibility, e.g. due to insufficient illumination of the road, or due to snow, rain, fog or spray R there is glare, e.
192.
Useful information ............................ 194 Important safety notes .................... 194 Displays and operation .................... 194 Menus and submenus ...................... 197 Display messages ............................. 212 Warning and indicator lamps in the instrument cluster .
Useful information i This Operator's Manual describes all models and all standard and optional equipment of your vehicle available at the time of publication of the Operator's Manual. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described.
If the coolant temperature is over 248 ‡(120 †), do not continue driving. The engine will otherwise be damaged. The coolant temperature gauge is in the instrument cluster on the right-hand side. Under normal operating conditions and with the specified coolant level, the coolant temperature may rise to 248 ‡(120 †).
Left control panel = ; R Calls up the menu and menu bar 9 : Press briefly: R Scrolls in lists R Selects a submenu or function R In the Audio menu: selects a stored station, an audio track or a video s.
A Permanen td isplay: outside temperature or speed ( Y page 206) B Time X To show menu bar ? : press the = or ; button on the steering wheel. Menu bar ? disappears after a few seconds. Text field = shows the selected menu or submenu as well as display messages.
The From Reset trip computer is automatically reset if the value exceeds 9,999 hours or 99,999 miles. ECO display Example: ECO display X Press the = or ; button on the steering wheel to select the Trip menu.
reset the values in the trip computer "From Start", the values in the "ECO display"are likewise reset. Navigation system menu Displaying navigation instructions X Switch on the audio system or COMAND; see the separate operating instructions.
Other status indicators of the navigation system R O :y ou have reached the destination or an intermediate destination. R New Route... or Calculating Route : calculating a new route R Off Map or Off Mapped Road :t he vehicle position is outside the area of the digital map (off-map position).
AUX mode ( Aux iliary audio mod e: external audio source connected). TV operation : Function ; Channel frequency with memory position i The memory positio ni s only displayed with channel ; if this has been stored. X Switch on COMAND and select TV; see the separate operating instructions.
Accepting ac all Example: incoming call X Press the 6 button on the steering wheel to accep ta ni ncoming call. If someone calls you when you are in the Tel menu, a display message appe ars in the multifunctio nd isplay. If you are not in the Tel menu, you can still accept a call.
R Activating/deactivating COLLISION PREVENTION ASSIST PLUS R Activating/deactivating ATTENTION ASSIST R Activating/deactivating Blind Spo tA ssist R Activating/deactivating Lane Keeping Assist Displaying the assistance graphic X Press the = or ; button on the steering wheel to select the DriveAssist menu.
Only deactivate ESP ® in the situations described in the following. It may be best to deactivate ESP ® in the following situations: R when using snow chains R in deep snow R on sand or gravel Activating/deactivating ESP ® on AMG vehicles ( Y page 66).
multifunction display in the assistance graphics display. For further information about ATTENTION ASSIST, see ( Y page 186). Activating/deactivating Blind Spot Assist X Press the = or ; button on the steering wheel to select the DriveAssist menu. X Press the 9 or : button to select Blind Spot Assist .
Instrumen tc luster Selecting the unit of measurement for distance You can determine whether the multifunction display shows some messages in miles or kilometers. X Press the = or ; button on the steering wheel to selec tt he Sett menu. X Press the : or 9 button to select the Inst.
the W symbol in the multifunction display are shown in orange . X Press the a button to save the setting. Further information on daytime running lamps ( Y page 105). Switching Adaptive Highbea mA ssist on/ off This function is only available on vehicles with the Intelligent Light System.
i Depending on your vehicle' se quipment, when the surround lighting and delayed switch-of fe xterior lighting are on, the following light up: R Parking lamps R Front fog lamps R Low-beam headlam.
Convenience Switching the fold-in mirrors with the locking feature on/off This function is only available on vehicles with the memory function ( Y page 100). When you activate the Auto. Mirror Folding function, the exterior mirrors are folded in when the vehicle is locked.
SETUP : Drive program ( C / S / M ) ; ESP ® mode ( ON / OFF ) or SPORT handling mode ( SPORT ) SETUP shows the drive program, the ESP ® (Electronic Stability Program) mode and the SPORT handling mode. X Press the = or ; button on the steering wheel to select the AMG menu.
SmartKey to position 2 or 3 and then press a to confirm Start , timing is continued. Resetting the current lap X Stop the RACETIMER. X Press the = or ; button to select Reset Lap . X Press a to reset the lap time to "0". Deleting all laps If you switch off the engine, the RACETIMER is reset to "0" after 30 seconds.
Display messages General notes Display messages appear in th em ultifunction display. Display messages with graphic displays may be shown in simplified for mi nt he Operator's Manual and may differ from the messages shown in the multifunction display.
Safety systems Display messages Possible causes/consequences and M Solutions !÷ Currently Unavailable See Operator's Manual ABS (Anti-lock Braking System), ESP ® (Electronic Stability Program), BAS (Brake Assist), the HOLD function and hill start assist are temporarily unavailable.
Display messages Possible causes/consequences and M Solutions The brake system continues to function normally, but without the functions listed above. The wheels could therefore loc ki fy ou brake hard, for example. The steerability and braking characteristics may be severely affected.
Display messages Possible causes/consequences and M Solutions ÷ Inoperative See Operator's Manual ESP ® , BAS, the HOLD function and hill start assist are unavailable due to a malfunction. COLLISION PREVENTION ASSIST/COLLISION PREVENTION ASSIST PLU Sm ay also have failed.
Display messages Possible causes/consequences and M Solutions F (USA only) ! (Canada only) Please Release Parking Brake The red F (USA only)/ ! (Canada only) indicato rl amp flashes and a warning tone sounds. Ac ondition for automatic release of the electric parking brake is not fulfilled ( Y page 154).
Display messages Possible causes/consequences and M Solutions The red F (USA only)/ ! (Canada only) indicato rl amp flashes and the yellow ! warning lamp lights up. The electric parking brake is malfunctioning. To release: X Switch off the ignition and turn it back on.
Display messages Possible causes/consequences and M Solutions The yellow ! warning lamp lights up. If you manually apply or release the electric parkin gb rake, the red F (USA only)/ ! (Canada only) indicator lamp flashes. The electric parking brake is malfunctioning.
Display messages Possible causes/consequences and M Solutions $ (USA only) J (Canada only) Check Brake Fluid Level There is no te nough brake fluid in the brake fluid reservoir. In addition, the $ (USA only)/ J (Canada only) warning lamp lights up in the instrument cluster and a warning tone sounds.
Display messages Possible causes/consequences and M Solutions 6 Front Left Malfunction Service Required or Front Right Malfunction Service Required SRS has malfunctioned at the front on the left or right. The 6 warning lamp also lights up in the instrumen tc luster.
Display messages Possible causes/consequences and M Solutions Front Passenger Airbag Disabled See Operator's Manual The front-passenger air bag is disabled during the journey, even though: R an a.
Display messages Possible causes/consequences and M Solutions Fo rf urther information about the Occupan tC lassification System, see ( Y page 45). Front Passenger Airbag Enabled See Operator's M.
Display messages Possible causes/consequences and M Solutions X Wait fo ra period of at least 60 seconds until the necessary system checks have been completed. X Make sure that the display messages do not appear in the multifunction display. If these conditions are fulfilled, the front-passenger seat can be occupied again.
Display messages Possible causes/consequences and M Solutions b Check Front Left Turn Signal or Check Front Right Turn Signal The front left-hand or front right-hand turn signal is defective. X Chec kw hether you are permitted to replace the bulb yourself ( Y page 111).
Display messages Possible causes/consequences and M Solutions b License Plate Lamp The lef to rr ight-hand license plate lamp is defective. X Check whether you are permitted to replace the bulb yourself ( Y page 111). or X Visit a qualified specialist workshop.
Display messages Possible causes/consequences and M Solutions b Check Rear Left Sidemarker Lamp or Check Rear Right Sidemarker Lamp The rear lef to rr ight side marker lamp is defective. X Check whether you are permitted to replace the bulb yourself ( Y page 111).
Engine Display messages Possible causes/consequences and M Solutions + Check Coolant See Operator's Manual The coolant level is too low. ! Avoid making long journeys with too little coolant in the engine cooling system. The engine will otherwise be damaged.
Display messages Possible causes/consequences and M Solutions # The battery is no tb eing charged. Aw arning tone also sounds. Possible causes are: R a defective alternator R a torn poly-V-belt R a malfunction in the electronics X Pull ove ra nd stop the vehicle safely and switch off the engine, paying attention to road and traffic conditions.
Display messages Possible causes/consequences and M Solutions ç There is only a very small amount of fuel in th ef uel tank. X Refuel at the neares tg as statio nw ithout fail. æ Gas Cap Loose The fuel system pressure is too low. The fuel filler cap is not closed correctly or the fuel system is leaking.
Display messages Possible causes/consequences and M Solutions Speed Limit Assist Inoperative Speed Limit Assis ti s faulty. X Visit a qualified specialist workshop. ë Off The HOLD function is deactivated. The vehicle is skidding. Aw arning tone also sounds.
Display messages Possible causes/consequences and M Solutions Blind Spot Assist Currently Unavailable See Operator's Manual Blind Spot Assis ti s temporarily inoperative. Possible causes are: R the sensors are dirty. R function is impaired due to heavy rain or snow.
Display messages Possible causes/consequences and M Solutions Park Assist Inoperative You have just carried out a large number of turning or parking maneuvers. Active Parking Assis tw ill become available again after approximately ten minutes ( Y page 178).
Display messages Possible causes/consequences and M Solutions DISTRONIC PLUS Inoperative DISTRONIC PLUS is defective. Adaptive Brake Assist may also have failed. Aw arning tone also sounds. X Visi ta qualified specialist workshop. DISTRONIC PLUS Passive You have depressed the accelerator pedal.
Tires Display messages Possible causes/consequences and M Solutions Check Tire Pressure Soon Canada only: The tire pressure loss wa rnin gs ystem has detected a significant loss in pressure.
Display messages Possible causes/consequences and M Solutions Check Tires The tire pressure in one or more tires has dropped significantly. The wheel position is displayed in the multifunction display.
Display messages Possible causes/consequences and M Solutions Tire Press. Monitor Currently Unavailable Due to a source of radi oi nterfe rence, no signals can be received from the wheel sensors .T he tire pressure monitor is temporarily malfunctioning.
Display messages Possible causes/consequences and M Solutions To Deselect P or N, Depress Brake and Start Engine You have attempted to shift the transmissio nt o position R or D without starting the engine. X Start the engine. X Depress the brake pedal.
Display messages Possible causes/consequences and M Solutions Transmission malfunction The automati ct ransmission is malfunctioning. X Visi ta qualified specialist workshop.
Display messages Possible causes/consequences and M Solutions M The hood is open. G WARNING The open hood may bloc ky our view when the vehicle is in motion. There is a risk of an accident. X Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions.
Display messages Possible causes/consequences and M Solutions Wiper Malfunctioning The windshield wipers are malfunctioning. X Visit a qualified specialist workshop. Hazard Warning Flashers Malfunctioning The hazard warning lamps are faulty. X Visit a qualified specialist workshop.
Problem Possible causes/consequences and M Solutions ü The red seat belt warning lamp lights up after the engine starts, as soon as the driver's or the front-passenger door is closed. The driver or front passenger has not fastened their seat belt.
Safety systems Problem Possible causes/consequences and M Solutions $ (USA only) J (Canada only) The red brake system warning lamp comes on while the engine is running. A warning tone also sounds. There is not enough brake fluid in the brake fluid reservoir.
Problem Possible causes/consequences and M Solutions ! The yellow ABS warning lamp is lit while the engine is running. ABS is temporarily unavailable. BAS, COLLISION PREVENTION ASSIST, COLLISION PREVE.
Problem Possible causes/consequences and M Solutions ! The yellow ABS warning lamp is lit while the engine is running. A warning tone also sounds. EBD is malfunctioning. Therefore, ABS, BAS, COLLISION PREVENTION ASSIST, COLLISION PREVENTION ASSIST PLUS, ESP ® , the HOLD function and hill start assist, for example, are not available either.
Problem Possible causes/consequences and M Solutions ÷ The yellow ESP ® warning lamp flashes while the vehicle is in motion. ESP ® or traction control has intervened because there is a risk of skidding or at least one wheel has started to spin. Cruise control or DISTRONIC PLUS is deactivated.
Problem Possible causes/consequences and M Solutions ÷å The yellow ESP ® and ESP ® OFF warning lamps are lit while the engine is running. ESP ® , BAS, COLLISION PREVENTION ASSIST, COLLISION PREVENTION ASSIST PLUS, the HOLD function and hill start assist are not available due to a malfunction.
Problem Possible causes/consequences and M Solutions F (USA only) ! (Canada only) The red indicator lamp for the electric parking brake flashes or lights up and/or the yellow warning lamp for the electric parking brake lights up. X Observe the additional display messages in the multifunction display.
Engine Problem Possible causes/consequences and M Solutions ; The yellow Check Engine warning lamp lights up while the engine is running. There may be a malfunction, for example: R in the engine manag.
Problem Possible causes/consequences and M Solutions ? The red coolant warning lamp comes on while the engine is running. The coolant level is too low. If the coolant level is correct, the airflow to the engine radiator may be blocked or the electric engine radiator fan may be malfunctioning.
Problem Possible causes/consequences and M Solutions X Leave the vehicle and keep a safe distance from the vehicle until the engine has cooled down. X Check the coolant level and add coolant ( Y page 283). Observe the warning notes. X If you need to add coolant more often than usual, have the engine coolant system checked.
Tires Problem Possible ca uses/consequences and M Solutions h The yellow tire pressure monitor warning lamp (pressure loss/ malfunction) is lit. The tire pressure monitor has detected a loss of pressure in at leas to ne of the tires.
252.
Useful information ............................ 254 Loading guidelines ............................ 254 Stowage areas .................................
Useful information i This Operator's Manual describes all models and all standard and optional equipment of your vehicle available at the time of publication of the Operator's Manual. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described.
R Always store objects so tha tt hey cannot be flung around in these or in similar situations. R Always make sure that objects do not protrude from stowage compartments, parcel nets or stowage nets. R Close lockable stowage compartments while driving.
Stowage compartment in front of the armrest (vehicles with automatic transmission) X To open: press the marking on cover : . i You can remove the non-slip mat and the insert for cleaning. When removing the insert you will have to overcome some slight resistance.
X To open: pull down the top of stowage compartment : by the edge of the handle. i Depending on the vehicle's equi pment, there may be an open stowage spa ce above the stowage compartment.
cupholder are folded in. They may otherwise be damaged. Observe the loading guidelines ( Y page 254). Folding the rear seat backrest forwards and back Folding the rear seat backrest forward The left-hand and right-hand rea rs eat backrests can be folded forwards separately to increase the trunk capacity.
R Do not route tie-downs acr oss sharp edges or corners. R Pad sharp edges for protecti on. : Cargo tie-down rings Stowage well under the trunk floor Under the trunk floor you can find a bra cket for TIREFIT and the vehicle tool kit, etc. X To open: pull handle : up.
Depending on the vehicle equi pment, ensure that when the roof carrier is installed you can: R open the panorama roo fw ith power tilt/ sliding panel fully R open the trunk lid fully The maximum roof load is 165 lbs((75 kg). An incorrectly secured roof carrier or roof load may become detached fro mt he vehicle.
X To remove: carefull y pull in uppe rs ections of cup holder : on the driver's and front- passenger sides until they release. X Lift the cup holder upwards ; until it can be removed. X To install: insert the cup holder into lateral curved sections ; in the stowage compartment .
Vanity mirror in the sun visor Mirror light : only functions if the sun visor is clipped into bracket ; and mirror cover A has been folded up. Glare from the side X Fold down su nv isor : . X Pull sun visor : out of retainer ; . X Swing sun visor : to the side.
There is a risk of fire and injury. Always hold the cigarette lighter by the knob. Always make sure that the cigarette lighter is out of reach of children. Never leave children unsupervised in the vehicle. Your attention must always be focused on the traffic conditions.
Socket in the rear-compartment center console X Pull cover : out by its top edge. X Lift up the cover of socket ; . Socket in the trunk X Lift up the cover of socket : . mbrace General notes You must have a license agreement to activate the mbrace service.
System self-test After you have switched on the ignition, the system carries out a self-diagnosis. Am alfunction in the system has been detected if one of the following occurs: R The indicator lamp in the SO Sb utton does not come on during the system self-test.
An emergency call can also be initiated manually. As soo na s the emergency call has been initiated, the indicator lamp in the SOS button flashes. The multifunction display shows the Connecting Call message. The audio output is muted. Once the connection has been made, the Call Connected message appears in the multifunction display.
X Press Roadside Assistance button : . This initiates a call to the Mercedes-Benz Customer Assistance Center. The indicator lamp in Roadside Assistance button : flashes while the call is active. The multifunction display shows the Connecting Call message.
If a mobile phone network and GPS reception are available, the system transfers data to the Mercedes-Benz Customer Assistance Center, for example: R Current location of the vehicle R Vehicle identification number i The audio system or COMAND display indicates that a call is active.
i The destination download function is available if the relevant mobile phone network is available and data transfer is possible. i The destination download function can only be used if the vehicle is equipped with a navigation system. Route Assistance This service is part of the mbrace PLUS Package and cannot be purchased separately.
Vehicle remote opening You can use the vehicle remote opening if you have unintentionally locked your vehicle and a replacement SmartKey is not available. The vehicle can be opened by the Mercedes- Benz Customer Assistance Center. The vehicle can be immediately opened remotely within fou rd ays of the ignition being turned off.
However, only the law enforce ment agency is informed of the location of the vehicle. i If the anti-theft alarm system is activated for longer than 30 second s, the Mercedes- Benz Customer Assistance Center is automatically informed.
Downloading routes Downloading routes allows you to transfer and save predefined routes in the navigation system. To do this, an SD memory card must be inserted into the COMAND system. If no SD memory card is inserted, you mus ti nsert the card into the card slot on the COMAND system before saving.
Garage door opener Important safety notes G WARNING When you operate or progra mt he garage door with the integrated garage door opener, persons in the range of movement of the garage door can become trapped or struck by the garage door. There is ar isk of injury.
X Press and hold one of buttons ; to ? on the integrated garage door opener. After a short time, indicator lamp : lights up yellow. i Indicator lamp : lights up yellow as soon as button ; , = or ? is programmed for the first time.
X Press and hold one of buttons ; to ? on the integrated garage door opener. After a short time, indicator lamp : lights up yellow. X Release the button. Indicator lamp : flashes yellow. X Press button B of garage door remote control A for two seconds, then release it for two seconds.
i Make sure that you clear the memory of the integrated garage door opener before selling the vehicle. Compass Calling up the compass The compass displays in which compass direction the vehicle is currently traveling: N , NE , E , SE , S , SW , W or NW .
seconds, until symbol C is shown in compass display ; ( Y page 276). X Drive your vehicle in a full circle at approximately 3 mph (5 km/h) to 6 mph (10 km/h). When the calibration has successfully been completed, the current direction is shown in compass display ; ( Y page 276).
278.
Useful information ............................ 280 Engine compartment ........................ 280 Maintenance ...................................... 284 Care .
Useful information i This Operator's Manual describes all models and all standard and optional equipment of your vehicle available at the time of publication of the Operator's Manual. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described.
! Make sure that the windshiel dw ipers are not folded away fro mt he windshield. You could otherwise damage the windshield wipers or the hood. X Make sure that the windshield wipers are switched off. X Pull release lever : on the hood. The hood is released.
Checking the oil level using the oil dipstick Example X Pull oil dipstick : out of the dipstick guide tube. X Wipe off oil dipstick : . X Slowly slide oil dipstick : into the guide tube to the stop, and take it out again. If the level is between MIN mark = and MAX mark ; , the oil level is correct.
Checking and adding other service products Checking coolan tl evel G WARNING The engine cooling system is pressurized, particularly when the engine is warm. When opening the cap, you could be scalded by hot coolant spraying out .T here is a risk of injury.
The washer fluid reservoir is used for both the windshield washer system and the headlamp cleaning system. If the washer fluid level drops below the recommended minimum of 1l iter, a message appears in the multifunction display prompting you to refill the washer fluid ( Y page 239).
Special service requirements The specified maintenance interval takes only the normal operation of the vehicle into account. Under arduous operating conditions or increased load on the vehicle, mainte.
! Make sure that the automatic transmission is in position N when washing your vehicle in a tow-through car wash. The vehicle could be damaged if the transmission is in another position. ! Make sure that: R the side windows and the sliding sunroof are fully closed.
Cleaning the wheels ! Do no tu se acidic wheel cleaning products to remove brake dust. This could damage wheel bolts and brake components. ! Do not park the vehicle for an extended period straight after cleaning it, particularly after having cleaned the wheels with wheel cleaner.
These notes also apply to light alloy wheels with a clear matte finish. i The vehicle should preferably be washed by hand using a soft sponge, car shampoo and plenty of water. i Use only insect remover and car shampoo from the range of recommended and approved Mercedes-Benz care products.
Cleaning the mirror turn signals ! Only use cleaning agents or cleaning cloths that are suitable for plastic lenses. Unsuitable cleaning agents or cleaning cloths could scrat ch or damage the plastic lenses of the mirror tur ns ignals.
their silky black shine. Rub the screen using a lightly oiled cloth after every car wash. Commercially available engine oils, WD 40 or Ballistol are suitable oi ls.
Cleaning the seat covers General notes ! Do no tu se microfiber cloths to clean genuine leather, artificial leather or Alcantara® covers. If used often, these can damage the cover. i Note that regula rc are is essential to ensure that the appearance and comfort of the covers is retained ove rt ime.
292.
Useful information ............................ 294 Where will I find...? ........................... 294 Flat tire .............................................. 295 Batter y( vehicle) ................................ 299 Jump-starting ..............
Useful information i This Operator's Manual describes all models and all standard and optional equipment of your vehicle available at the time of publication of the Operator's Manual. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described.
The tire-change tool kit contains: R Jack R Lug wrench R One pair of gloves R Folding wheel chock Flat tire Preparing the vehicle Your vehicle may be equipped with: R MOExtended tires (tires with run-flat properties) ( Y page 295) Vehicle preparation is not necessary on vehicles with MOExtended tires.
conditions/maneuvers, or it can be incre ased through a moderate style of driving. The maximum permissible distance which can be driven in run-flat mode is counted from the moment the tire pressure loss warning appears in the multifunction di splay. You mus tn ot exceed a maximum speed of 50 mph (80 km/h).
R Immediately change out of clothing which has come into contact with tire sealant. R If an allergic reaction occurs, seek medical attention immediately. Using the TIREFI Tk it TIREFIT is a tire sealant. You can use TIREFIT to seal punctures of up to 0.
i First, tire sealant is pumped into the tire. The pressure can briefly rise to approximately 500 kPa (5 bar/73 psi). Do no ts witch off the tire inflation compressor during this phase. X Let the tire inflation compressor run for a maximum of te nm inutes.
X Stop after driving for approximately ten minutes and check the tire pressure with the tire inflation compressor. The tire pressure mus tn ow be at least 130 kPa (1.3 bar/19 psi). G WARNING If the required tire pressure is not reached after driving for a short period, the tire is too badly damaged.
G WARNING Work carried out incorrectly on the battery can lead, for example, to a short circuit and thus damage the vehicle electronics. This can lead to function restrictions applying to safety-relevant systems, e.g. the lighting system, ABS (anti-lock braking system) or ESP ® (Electronic Stability Program).
special collection point for used batteries. ! Have the battery checked regularly at a qualified specialist workshop. Observe the service intervals in the Maintenance Booklet or contact a qualified specialist workshop for more information. ! You should have all work involving the battery carried out at aq ualified specialist workshop.
consumers .T he vehicle will then use very little energy, thus conserving battery power. i If the power supply has been interrupted, e.g. if you reconnect the battery, you will have to: R set the clock (audio system/COMAND, see the separate operating instructions).
Jump-starting For the jump-starting procedure, use only the jump-starting connection point, consisting of a positive terminal and an earth point, in the engine compartment. G WARNING Battery acid is caustic. There is a risk of injury. Avoid contact with the skin, eyes or clothing.
Do not start the vehicl eu sing a rapid charging device. If your vehicle's battery is discharged, the engine can be jump-started from another vehicle or from a second battery using jumper cables. Observe the following points: R The battery is not accessible in all vehicles.
Position number B identifies the charged battery of the other vehicle or an equivalent jump- starting device. X Press together cover : of positive clamp ; and slide it back. X Connec tp ositive terminal ; on your vehicle to positive terminal = of donor battery B using the jumper cable, beginning with your own battery.
! If DISTRONIC PLUS or the HOLD function is activated, the vehicle brakes automatically in certain situations. To prevent damage to the vehicle, deactivate DISTRONIC PLUS and the HOLD function in the following or other simila rs ituations: R when towing the vehicle R in the car wash ! Only secure the tow rope or tow bar at the towing eyes.
Towing the vehicle with the front axle raised Only vehicles without 4MATIC can be towed with the front axle raised. ! Vehicles with 4MATIC must not be towed with either the front or the rea ra xle raised, as doing so will damage the transmission.
Notes on 4MATIC vehicles ! Vehicles with 4MATIC must not be towed with eithe rt he front or the rear axle raised, as doing so will damage the transmission. Vehicles with 4MATIC may only either be towed away with both axles on the ground or be loaded up and transported.
! Make sure that no moisture can enter the fuse box when the cover is open. ! When closing the cover, make sure that it is lying correctly on the fuse box. Moisture seeping in or dirt could otherwise impair the operation of the fuses. X Open the hood.
310.
Useful information ............................ 312 Important safety notes .................... 312 Operation ........................................... 312 Winter operation ............................... 314 Tire pressure ..........................
Useful information i This Operator's Manual describes all models and all standard and optional equipment of your vehicle available at the time of publication of the Operator's Manual. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described.
the unusual handling characteristics .I fy ou find no signs of damage, have the wheels and tires checked at a qualified specialist workshop. R When parking your vehicle, make sure that the tires do not get deformed by the curb or other obstacles.
Bar indicator : for tread wear is integrated into the tire tread. Treadwear indicators (TWI) are required by law. Six indicators are positioned on the tire tread. They are visible once the tread depth is approximately á in (1.6 mm). If this is the case, the tire is so wo rn that it mus tb e replaced.
safety systems such as ABS and ESP ® to function optimally in winter. These tires have been developed specifically for driving in snow. Use M+S tires of the same make and tread on all wheels to maintain safe handling characteristics. Always observe the maximum permissible speed specified for the M+S tires you have mounted.
Tire pressure Tire pressure specifications G WARNING Underinflated or overinflated tires pose the following risks: R the tires may burst, especially as the load and vehicle speed increase. R the tires may wear excessively and/or unevenly, which may greatly impai rt ire traction.
Example: tire pressure table wi th tire dimensions Some tire pressure tables sho wo nly the rim diameters instead of the full tire size, e.g. R18 .R im diameter is part of the tire size and can be found on the tire sidewall ( Y page 330).
checking the pressure of warm tires. Only correct the tire pressure if it is too low for the current operating conditions .I fy ou check the tire pressure when the tires are warm, the resulting value will be higher than if the tires were cold. This is normal.
Information on air pressure for the tires on you rv ehicle can be found: R on the vehicle's Tire and Loading Information placard on the B-pillar R on the tire pressure label on the fuel filler fl.
X Before restarting, make sure that the tire pressures are set properly on all fou rt ires for the respective operating conditions. The recommended tire pressures can be found on the Tire and Loading Information placard on the B-pillar on the driver's side or the tire pressure table on the fuel filler flap.
tires are significantly underinflated. Accordingly, when the low tire pressure telltale illuminates, you shoul ds top and check your tires as soo na s possible, and inflate them to the proper pressure. Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure.
The tire pressure values indicated by the on- board computer may differ from those measured at a gas station with a pressure gauge. The tire pressures shown by the on- board computer refer to those measured at sea level. At high altitudes, the tire pressure values indicated by a pressure gauge are higher than those shown by the on-board computer .
X Set the tire pressure to the value recommended for the corresponding driving situation on the Tire and Loading Information placard on the dri ver's side B-pillar ( Y page 316). Additional tire pressure values for different loads can also be found on the tire pressure table on the inside of the fuel fille rf lap ( Y page 316).
The maximum gross axle weight rating is the maximum weight that can be carried by one axle (front or rear axle). Never exceed the maximum load or the maximum gross axle weight rating for the front or rear axle.
X Step 4: The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the "XXX" amount equals 1400 lbs and there are five occupants in the vehicle each with a weight of 150 lbs, the amount of available cargo and luggage load capacity is 650 lbs (1400 Ò 750 (5 x 150) = 650 lbs).
Example: steps 1 to 3 The following table shows examples on how to calculate total and cargo load capacities with varying seating configurations and number and size of occupants. The following examples use a maximum load of 1500 lbs (68 0k g) . This is fo ri llustration purposes only.
Example 1 Example 2 Example 3 Step 3 Permissible load and trailer load/ noseweight (maximum permissible load rating from the Tire and Loading Information placard minus the gross weight of all occupant.
Uniform Tire Quality Grading Standards Overview of Tire Quality Grading Standards Uniform Tire Quality Grading Standards are U.S. government specifications. Their purpose is to provide drivers with uniform reliable information on tire performance data.
not covered with ice or snow. Take appropriate care when driving. ! Avoid wheelspin. This can lead to damage to the drive train. Temperature G WARNING The temperature grade for this tire is established for a tire tha ti s properly inflated and not overloaded .
Tire size designation ,l oad-bearing capacity and speed rating : Tire width ; Nominal aspec tr atio in % = Tire code ? Rim diameter A Load bearing index B Speed rating i Tire data is vehicle-specific and may deviate from the data in the example.
adapt your driving style to the traffic conditions. Summer tires Index Speed rating Q up to 100mph (160 km/h) R up to 106mph (170 km/h) S up to 112mph (180 km/h) T up to 118mph (190 km/h) H up to 130mph (210 km/h) V up to 149mph (240 km/h) W up to 168mph (270 km/h) Y up to 186mph (300 km/h) ZR.
Load index In addition to the load bearing index, load index : may be imprinted after the letters that identify speed index B ( Y page 330) on the sidewall of the tire.
Tire characteristics This informatio nd escribes the tire cord and the number of layers in sidewall : and under tire tread ; . i Tire data is vehicle-specific and may deviate from the data in the example.
GAWR (Gross Axle Weight Rating) The GAWR is the maximu mg ross axle weight rating. The actual load on an axle must never exceed the gross axle weight rating. The gross axle weight rating can be found on the vehicle identification plate on the B-pillar on the driver's side.
Aspect ratio Relationship between tire height and tire width in percent. Tire pressure This is pressure inside the tire applying an outward force to each square inch of the tire's surface. The tire pressure is specified in pounds per square inch (psi), in kilopascal (kPa) or in bar.
Changing aw heel Flat tire You can find information on wha tt o do in the event of a flat tire in the "Flat tire" section ( Y page 295). Information on driving with MOExtended tires in the event of a flat tire can be found under "MOExtended tires (tires with run-flat characteristics" ( Y page 295).
X Bring the front wheels into the straight- ahead position. X Move the DIRECT SELECT lever to position P . X Switch off the engine. X Remove the SmartKey from the ignition lock. X If included in the vehicle equipment, remove the tire-change tool kit from the vehicle.
Observe the following when raising the vehicle: R to raise the vehicle, only use the vehicle- specific jack that has been tested and approved by Mercedes-Benz .I fu sed incorrectly, the jack could tip over with the vehicle raised. R the jack is designed only to raise and hold the vehicle for a short time while a wheel is being changed.
Covers, fron t( example: vehicles with AMG equipment) AMG vehicles and vehicles with AMG equipment: to protec tt he vehicle body, the vehicle has covers next to the jacking points on the outer sills. X AMG vehicles and vehicles with AMG equipment: fold cover ; upwards.
! To prevent damage to the paintwork, hold the wheel securely against the wheel hub while screwing in the first wheel bolt. X Clea nt he wheel and wheel hub contact surfaces. X Place the new wheel on the wheel hub and push it on. X Tighten the wheel bolts until they are finger-tight.
vehicle noise emissions or fuel consumption, may otherwise be adversely affected. In addition, when driving with a load, tire dimension variations coul d cause the tires to come into contact with the bodywork and axle components. This coul d result in damage to the tires or the vehicle.
Tires Summer tires Allo yw heels V1 V2 BA 225/40 R18 92 W XL MOExtended 6, 7, 8 7.5 J x 18 H2 Wheel offset: 2.05 in (52 mm) # — BA 235/40 ZR18 95 YX L 6 8.0 J x 18 H2 Wheel offset: 1.89 in (48 mm) — # BA 235/35 ZR19 91 YX L 6 8.0 J x 19 H2 Wheel offset: 1.
Useful information ............................ 344 Information regarding technical data .................................................... 344 Warranty .............................. .............. 344 Identification plates ........................
Useful information i This Operator's Manual describes all models and all standard and optional equipment of your vehicle available at the time of publication of the Operator's Manual. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described.
Example: vehicle identification plate (Canada only) ; VIN = Paint code i The data shown on the vehicle identificatio np late is used only as an example. This data is differen tf or every vehicle and can deviate from the data shown here. You can find the data applicable to your vehicle on the vehicle identification plate.
Service products include the fol lowing: R Fuels R Lubricants (e.g. engine oil, transmissio no il) R Coolant R Brake fluid R Windshield washer fluid R Climate control system refrigerant Components and service products must be matched .Y ou should therefor eo nly use products tha th ave been tested and approved by Mercedes-Benz.
the fu el system. Even small amounts of the wrong fuel could resul ti nd amage to the fuel system and the engine. Notify a qualified specialist workshop and have th e fuel tan ka nd fuel lines dra ined completely. ! Only refuel using unleaded gasol ine with a minimum octane rating of 91.
Engine oil General notes ! Never use engine oil or an oil filter of a specificatio no the rt han is necessary to fulfill the prescribed service intervals. Do not change the engine oil or oil filter in order to achieve longer replacement intervals than those prescribed.
hard. This would impair braking efficiency. There is a risk of an accident. You should have the brake fluid renewed at the specified intervals. When handling brake fluid, observe the important safety notes on service products ( Y page 345). The brake fluid change intervals can be found in the Maintenance Booklet.
Filling capacities Model Capacity CLA 250 Approx. 8.2 US qt (7.8 l) i Use antifreeze/corrosio ni nhibitor according to MB approval 325.0 or 326.0. Windshiel dw asher system Important safety notes G WARNING Windshield washer concentrate is highly flammable.
Refrigerant instruction label Example: refrigerant instruction label : Warning symbol ; Refrigerant filling capacity = Applicable SAE standards ? PAG oil part number A Type of refrigerant Warning symb.
CLA 45 AMG 4MATIC Vehicle height 55.7 in (1416 mm) Wheelbase 106.3 in (2699 mm) Turning radius 36.2 ft (11.04 m) Maximum roof load 352 Vehicle data Technical data.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Mercedes-Benz CLA (2014) è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Mercedes-Benz CLA (2014) - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Mercedes-Benz CLA (2014) imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Mercedes-Benz CLA (2014) ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Mercedes-Benz CLA (2014), ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Mercedes-Benz CLA (2014).
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Mercedes-Benz CLA (2014). Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Mercedes-Benz CLA (2014) insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
