Manuale d’uso / di manutenzione del prodotto 14592RB del fabbricante McCulloch
Vai alla pagina of 84
12592RB 14592RB Instruction manual Please read these instructions carefully and make sure you understand them before using this machine. Anleitungshandbuch Bitte lesen Sie diese Anleitungen sorgfältig durch und vergewissern Sie sich, daß Sie diese verstehen, bevor Sie die Maschine in Betrieb nehmen.
2 1 2 3 4 5 6 7 8 3 18 36 44 47 58 78 81 Safety rules. Reglas de seguridad. Sicherheitsvorschriften. Norme antinfortunistiche. Règles de sécurité. Ve iligheidsregels. Assembly. Montaje. Zusammenbau. Montaggio. Montage. Montering. Functional description.
3 1. Safety Rules Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I .
4 IV. Maintenance and Storage • Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition. • Never store the equipment with petrol in the tank inside a building where fumes may reach an open flame or spark. • Allow the engine to cool before storing in any enclo- sure.
5 • Bei Maschinen mit mehreren Mähmessern ist Vorsicht geboten, da beim Drehen eines Mähmessers die anderen Mähmesser sich womöglich mit drehen. III. Betrieb • Maschine nicht in einem geschlossenen Bereich betreiben, in dem die gefährlichen Kohlenmoxydgase sich sammeln können.
6 • Alle Anbaugeräte-Antriebe ausschalten, den Motor abstellen und das (die) Zündkerzenkabel abziehen bzw. den Zündschlüssel abziehen: - vor dem Entfernen von Verstopfungen aus dem Mähwerk oder dem Auswurf; - vor dem Prüfen, Reinigen oder Reparieren des Rasenmähers; - nachdem auf ein Fremdkörper gestoßen wurde.
7 III. Utilisation • Ne démarrez jamais le moteur à l'intérieur d'un bâtiment où des vapeurs dangereuses de monoxyde de carbone pourraient s'être accumulées. • Tondez uniquement à la lumiére du jour ou avec une bonne lumière artificielle.
8 • Débrayez les lames, arrêtez le moteur, et débranchez le (s) fil (s) de la bougie d'allumage ou enlevez la clef de contact: - avant de retirer l'insert broyeur ou avant de retirer la goulotte d'éjection pour la nettoyer.
9 1. Reglas De Seguridad Prácticas de Operación Seguras para las Segadoras Conducibles IMPORTANTE: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE.
10 • Desenganche la transmisión a los accesorios, pare el motor, y desconecte el (los) cable (s) de la bujía o remueva la llave de ignición - antes de limpiar bloqueos o desatrancar del conducto; - antes de inspeccionar, limpiar o trabajar sobre la segadora; - después de golpear un objeto extraño.
11 I . Addestramento All 'Uso • Studiare attentamente le istruzioni. Acquisire dimestichezza con i comandi e conoscere a fondo l’uso corretto dell’equipaggiamento. • Non consentire mai l’uso dei trattorini tosaerba ai bambini né agli adulti che non abbiano dimestichezza con le istruzioni sull’uso.
12 • Disinnestare la trasmissione del moto agli accessori, spegnere il motore e scollegare i fili delle candele oppure togliere la chiavetta di accensione: - prima di pulire eventuali intasamenti e .
13 I . Training • Lees de instructies aandachtig. Zorg dat u vertrouwd bent met de bedieningselementen en het juiste gebruik van de machine. • Laat kinderen of mensen die niet bekend zijn met de instructies, de maaimachine niet gebruiken. Het is mogelijk dat plaatselijke voorschriften een beperking stellen aan de leeftijd van de bestuurder.
14 • Schakel de aandrijving naar de hulpstukken uit, stop de motor en maak de bougiekabel(s) los of verwijder het contactsleuteltje, - voordat u opgehoopt materiaal weghaalt of een verstopte afvoer leeg maakt; - voordat u de maaimachine controleert, schoonmaakt of eraan werkt; - nadat u een ongewenst voorwerp heeft geraakt.
15 BATTERY BATTERIE BATTERIE ACCU BATERÍA BATTERIA CAUTION VORSICHT DANGER OPGELET PRECAUCIÓN ATTENZIONE BEWARE OF THROWN OBJECTS VORSICHT, HOCHGESCHLEUDERT GEGENSTÄNDE ATTENTION AUX PROJECTILES LE.
16 Eng F Esp NL These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut.
17 GEFAHR AUGEN SCHÜTZEN EXPLOSIVE GASE KÖNNEN ERBLINDUNG UND KÖRPERVERLETZUNGEN VERURSAC-HEN. GEVAAR OGEN BESCHERMEN EXPLOSIEVE GASSEN KUNNEN BLINDHEID OF LETSEL VEROORZAKEN. PELIGRO PROTEJE SUS OJOS GASES EXPLOSIVOS PUEDEN CAUSAR CEGUE-DAD O LESIONES.
18 2. Assembly . 2. Zusammenbau. 2. Montage. 2. Montaje 2. Montaggio. 2. Montering. 1 STEERING WHEEL • Mount extension shaft (1). Tighten securely. • Mount the main shaft cover. Make sure that the guide tabs in the cover fit the cover in respective holes.
19 1 F NL Esp VOLANT DE DIRECTION • Monter la rallonge d'arbre de direction sur les orifices souhaités puis installer la vis hexagonale et l'écrou frein, bien serrer le tout, • Positionner le cache sur la colonne de direction.
20 Seat Remove the hardware securing seat to the cardboard pack- ing and set the hardware aside for assembly of seat to tractor. Pivot seat upward and remove from cardboard packing. Remove the cardboard packing and discard. Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan (1).
21 NL Esp Install battery NOTE: If battery is put into service after month and year indicated on label, charge battery for minimum of one hour at 6-10 amps. WARNING: Before installing battery remove metal brace- lets, wrist watch bands, rings, etc. from your person.
22 F NL Eng Esp WARNING: Positive terminal must be connected first to prevent sparks from accidental grounding. Remove terminal caps and discard. Connect the red cable to + and then the black earth cable to -. Screw tight the cables. Grease the battery poles with vaseline to prevent corrosion.
23 Eng TO ADJUST GAUGE WHEELS Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain con- ditions.
24 To install bagger components to tractor 1 2 1. Discharge Chute 2. 3/8 Nut 3. Flat Washer 3 1 2 1. 3/8 Lock nut 2. Flat Washer 3. Support Tube 3 5 3 1 4 2 1. Support Bracket 2. 3/8 Carriage Bolt 3. 3/8 Lock Nut 4. 3/8 x 63,5mm Hex Bolt 5 . 10,3mm (13/32") flat washer 1 .
25 To Assemble Bagger NOTE: For ease of assembly, you may wish to obtain the assistance of another person when putting the bagger to- gether. • Holes in front bagger tube are at an angle. Place front bagger tube against lower bagger tube and check for proper hole alignment before assembling bolts.
26 Installation der Aufhängung der Grasfangbox des Traktors 1 2 1 3 2 1. Kontermutter 2. Flache Unterlegscheibe 3. Halterungder Grasfangbox 3 5 3 1 4 2 1. Strebe 2. Tragbolzen 3/8 3. Kontermutter 3/8 4. Sechskantbolzen 3/8 x 63,5mm 5. Flache Unterlegscheibe 10,3mm (13/32) 1 .
27 1. Vorderer Rahmen der Grasfangbox 2 . Unterer Rahmen der Grasfangbox 3. Tragbolzen 1/4 x 50,8mm 4. Kontermutter 1/4 1 . Ausgleichende Oberfläche 2 . Höhenjustierung 3. Seitenjustierung 5 6 2 7 1 4 3 1 6MM (1/4") - 9MM (3/8") 2 85˚ 2 4 1 3 3 1.
28 Assemblage des composants du collecteur 1 2 1. Manche de décharge 2. 3/8 Écrou 3. Rondelle Plate 1 3 2 1. Contre Écrou 2. Rondelle plate 3. Tube de support 1. Console de support 2. Boulon de support 3/8 3. Contre-ècrou 3/8 4. Boulon à tête hèxagonale 3/8 x 63,5 5.
29 Pour assembler le collecteur REMARQUE: Pour faciliter l'assemblage, vous pouvez obtenir l'aide d'une autre personne en remontant le ramasse- herbe.
30 Para montar los componentes del contenedor para costales al tractor 1 2 1. Descarga de adaptarse 2. Tuercas de 3/8 3. Arandelas planas 1. Contratuercas de 3/8 2. Arandelas planas de 13/32 3. Tubo de soporte 1. Consola portadora 2. tornillo portadora 3/8 3.
31 Para montar el contenedor NOTA: Para facilitar el ensamblaje de la recolectora dehierba,se aconseja efectuar las operaciones con de la ayuda de otra persona.
32 Per montare i componenti del cesto di raccolta 1 2 1. Convogliatore di scarico 2. Dadi 3/8 3. Rondella Piatta 1 . Dadi 2. Rondella Piatta 3. Telaio di supporto 1. Staffa di supporto 2. Bullone di supporto (3/8) 3. Dadi 3/8 4. Bullone a testa esagonale (3/8 x 63,5mm) 5.
33 Per montare il cesto di raccolta: NOTA : per facilitare l’assemblaggio, nell’installare il sacco può essere utile farsi aiutare da un’altra persona.
34 Hetmonteren van componenten van de grascontainer op de trekker 1 2 1. Afvoertrechter 2. 3/8 borgmoer 3. Vlakke sluitring 1. Borgmoer 3/8 2. Vlakke sluitring 3. Steun 1. Stennijzer 2. 3/8 Slotbout 3. 3/8 borgmoer 4. 3/8 Zeskantbout 5. Vlakke sluitring 10,3 mm (13.
35 De grascontainer monteren N.B.: Indien gewenst kunt u de grascontainer samen met iemand anders in elkaar zetten om het assembleren makkelijker te maken.
36 3. Functional description. 3. Funktionsbeschreibung. 3. Description du fonctionnement. 3. Descripción del funcionamiento. 3. Funzionamento. 3. Beschrijving van functies Positioning of controls 1. Light Switch Position. 2. Throttle Control. 3. Brake and clutch pedal.
37 Emplacement des commandes 1. Interrupteur des phares. 2. Commande de gaz. 3. Pédale de frein et d'embrayage. 4. Levier de changement de vitesse. 5. Embrayage et débrayage de groupe de coupe. 6. Abaissement et relevage du plate au de coupe. 7.
38 Eng Esp F NL 2. Throttle control The throttle control regulates the engine revs and thus the rotation speed of the blades. = Full speed = Idling speed 2. Gashebel Mit dem Gashebel wird die Drehzahl des Motors und damit die Drehgeschwindigkeit des Mähaggregats geregelt.
39 3. Brake and clutch pedal When the pedal is pushed down the brake is applied and the motor is disengaged. 3. Brems- und Kupplungspedal Beim Vorwärtsdrücken des Pedals wird das Fahrzeug abge- bremst. Gleichzeitig wird der Motor ausgekuppelt und das Fahrzeug rollt aus.
40 4. Gear shift lever The gear box has positions forward, neutral and reverse. Gear changing can take place from neutral to top gear without stopping in each gear position. Disengage the motor at each gear position! Start can take place irrespective of the gear lever position.
41 6. Quick lifting/lowering of the cutting unit Pull the lever backwards to quickly lift the cutting unit when passing over irregularities in the lawn, etc. During transpor- tation the cutting unit shall be in the highest position. Pull the lever back until it locks.
42 8. Parking brake Connect the parking brake in the following way: 1. Press down the brake pedal to bottom position. 2. Move the parking brake lever upwards and hold in this position. 3. Release the brake pedal. To release the parking brake all that is necessary is to push down the brake pedal.
43 F Esp NL 8. Frein de parking Pour enclencher le frein de parking : 1. Enfoncer à fond la pédale de frein/embrayage. 2. En même temps, relever vers le haut le levier du frein de parking et le maintenir dans cette position. 3. Relâcher la pédale de frein.
44 4. Before starting. 4. Maßnahmen vor dem Anlassen. 4. Avant de démarr er . 4. Antes del arranque. 4. Prima dell’avviamento. 4. Maatregelen vóór het starten. Filling up The engine should be run of pure (not oil mixed) unleaded petrol. Do not fill beyond the lower edge of the filling hole.
45 ADD FULL CAUTION - DO Oil level The combined oil refilling cap and the oil stick is accessible when the bonnet is lifted forwards. The oil level in the engine should be checked before each run. Make sure that the tractor is horizontal. Unscrew the oil stick and wipe clean.
46 Tire air pressure Check the tire pressure regularly. The pressure in the front tires should be 1 bar (14 PSI) and 0.8 bar (12 PSI) in the back tires. Reifendruck Den Luftdruck in den Reifen regelmäßig prüfen. Der Druck in den Vorderreifen soll 1 bar betragen, in den Hinterreifen 0,8 bar.
47 5. Driving. 5. Betrieb. 5. Conduite. 5. Conducción. 5. Guida. 5. Rijden. Démarrage du moteur S’assurer que le carte de coupe est en position de transport (en position supérieure) et que le levier pour l’embrayage/ débrayage du carte de coupe est en position de débrayage.
48 Pull out the choke control (if engine is cold). Den Kaltstarthebel herausziehen (nur bei kaltem Motor). Tirer le starter (si le moteur est froid). Extraer el estrangulador (únicamente si el motor está frío). Estrarre il comando dello choke (in caso di partenza a freddo).
49 Turn the ignition key to “START position”. NOTE! Do not run the start motor more than 5 seconds at once. If the engine will not start, wait about 10 seconds before the next try. Zündschlüssel auf “START” drehen. HINWEIS! Den Anlasser nicht jeweils länger als ca.
50 NOTA! La máquina tiene un interruptor de seguridad que corta la corriente al motor si el conductor sale del asiento con el motor en marcha y con la palanca de acoplamiento/ desacoplamiento en la posición de acoplamiento.
51 Cutting tips • Clear the lawn from stones and other objects which can be thrown away by the blades. • Localize and mark stones and other fixed objects to avoid collision. • Begin with a high cutting height and reduce until the required cutting result is obtained.
52 Consigli per il taglio dell’erba • Pulire il prato da pietre e altri corpi estranei. • Individuare ostacoli fissi. • Cominciare con un’altezza di taglio elevata e scendere progressivamente. • I migliori risultati si ottengono con un elevato regime del motore (lame che girano veloci) e marcia bassa (la macchina si muive lentamente).
53 To Dump Bagger Your tractor is equipped with a Dump Bag Alarm. To turn off the alarm disengage the attachment clutch switch. • Position tractor in location you wish to dump bagger. • Place motion control lever in Neutral position and set parking brake.
54 To convert mower (Converting to mulching or rear discharging will require the purchase of these accessories.) To mulching • Place deck into the high cut position. • Remove bagger or optional rear discharge deflector. • Unhook the two (2) straps and remove discharge chute.
55 Para cambiar el ajuste de la segadora (Un cambio de ajuste para no recoger la hierba o usarla tipo mulching requiere la compra de los mecanismosdispositivos siguientes) Para cortar tipo mulching .
56 ATTENTION! • Ne pas conduire sur un terrain incliné de plus de 10º. Le risque de se renverser est très important. • Ne jamais conduire le tracteur parallèlement à la pente à cause du risque de se renverser. Toujours conduire le tracteur perpendiculairement à la pente, pour monter comme pour descendre.
57 Switching off the engine Move the gas control to “ ”. Disconnect the cutting unit by moving the connect/disconnect lever downwards. Lift up the cutting unit and turn the ignition key to “OFF” position. Allow the engine to idle for 1-2 minutes to cool down before switching off after a hard work.
58 6. Maintenance, adjustment. 6. W ar tung (Instandhaltung), Einstellung. 6. Entretien, réglages. 6. Mantenimiento, ajuste. 6. Manutenzione. 6. Onderhoud, afstelling. WARNING! Before servicing the engine or cutting unit the following shall be carried out: • Press down the clutch/brake pedal and engage the parking brake lever.
59 1 2 (1) Capot (2 ) Connexion des phares (1) Cubierta (2 ) Conector de cables de los faros delanteros (1) Cofano (2 ) Connettore cavo luci (1) Motorkap (2) Aansluitkabel koplampen F Esp NL Esp NL Capot moteur • Soulever le capot.
60 Mantenimiento NOTA : El mantenimiento periódico ha de hacerse con regularidad a fin de mantener el tractor en buen estado. ADVERTENCIA : Antes de efectuar cualquier reparación, inspección o maintenimiento, desconectar el cable de la bujía a fin de evitar accidentes.
61 To service engine See engine manual. Oil drain valve • Remove cap and install drain tube. • To open valve, push in slightly, turn counterclockwise and pull out. • To close valve, push in and turn clockwise . • Remove drain tube and install cap.
62 SERVICE RECORD Fill in dates as you complete regular service Change engine oil ............................................................................ • Lubricate pivot points .................................................................
63 COMPE-RENDU D'ENTRETIEN Indiquer les dates après chaque mesure d'entretien Vidange d'huile moteur ..................................................................... • Graissage des articulations ................................
64 DATI DI SERVIZIO Compilare ogni qualvolta si esegue un regolare servizio Necessità Ogni Ogni Ogni . Ogni Ogni 8 ore 25 ore 50 ore 100 ore 200 ore Cambio dell'olio ...............................................................................
65 Blades The blades should be sharp to achieve best cutting results. Sharpening can be carried out with a file or grinding disc. NOTE! It is very important that both blades are sharpened equally to avoid imbalance. Messerbalken Für ein gutes Mähergebnis müssen die messcrbalken scharf sein.
66 5 Star pattern blade The center of this blade has a five (5) star pattern. The bolt that attaches this blade has normal Right Hand threads that loosens by turning ( ) counter-clockwise and tightens by turning ( ) clockwise. Messerbalkenbohrung mit fünfeckige Aussparung Die Bohrung des Messerbalkens hat eine fünfeckige Aussparung.
67 Cuchilla de orificio-estrella de cinco puntas El centro de esta cuchilla se parece a una estrella de cinco (5) puntas. El tornillo que liga esta cuchilla es dextrogiro normal y se desentornilla en direcciûn opuesta a la vuelta de la aguja del reloj y se emperna dandole vueltas en la direcciûn de la aguja del reloj.
68 For best results mower blades must be kept sharp. Replace bent or damaged blades. BLADE REMOVAL • Raise mower to highest position to allow access to blades. • Remove hex bolt, lock washer and flat washer securing blade. • Install new or resharpened blade with trailing edge up towards deck as shown.
69 WARNING! Do not forget to tighten the lock nut after complet- ing adjustment. WARNUNG! Nicht vergessen, die Sicherungsmutter nach durchgeführter Einstellung anzuziehen. ATTENTION! Ne pas oublier de serrer l’écrou de verrouillage après le réglage.
70 1 2 Dismantling of the cutting unit Work from the right side of the machine. 1. Take off the belt from the engine pulley (1). 2. Remove the two rear retainer springs (2) and knock off the axle taps with a hammer. Demontage des Mähdecks Arbeiten Sie auf der rechten Seite der Maschine.
71 4 3 5 Assembly of the cutting unit • Push in the cutting unit under the machine. • Assemble in the reverse order to dismantling. Einbau des Mähdecks • Mähdecks unter den Traktor schieben. • Der Einbau erfolgt in umgekehrter Reihenfolge. Montage du groupe de coupe • Pousser le groupe de coupe sous la machine.
72 Replacement of drive belt for cutting unit 1. Dismantle the cutting unit as described previously. 2. Work off the belt from the unit's left pulley and then from the other wheels. 3. Pull the belt away from the cutting unit. 4. The new belt is mounted in the reverse order.
73 B A Adjustment of the cutting unit A. In the direction of travel 1. Check that the air pressure is correct in all four tires. 2. Make sure that the machine is on a horizontal surface. 3. Lift up the cutting unit to its highest position. 4. Measure the distances A and B.
74 “A” 2 REGLAGE TRANSVERSAL • Relever le carter de coupe dans sa position la plus haute. • Calculer la distance au sol à partir des milieux des bords extérieurs gauche et droite du carter de coupe. • La distance A doit être la mêne des deux côtés à 6 mm près.
75 Replacement of drive belt 1. Dismantle the cutting unit as described previously. 2. Dismantle the motion restrainer for the clutch (1). 3. Engage the parking brake and work off the belt upwards from the pulley (2), the clutch pulley (3). 4. Work off the belt upwards from the pulley at the rear axle (4).
76 TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows: • Make sure transaxle is in neutral (N).
77 REGOLAZIONE DELLA LEVA DEL MECCANISMO DEL CAMBIO DI VELOCITÀ CON DIFFERENZIALE Il meccanismo del cambio con differenziale deve essere in posizione di folle quando la relativa leva è in posizione di folle (N) (blocco). Tale condizione viene impostata al momento della fabbricazione.
78 7. T r oubleshooting. 7. Störungssuche. Engine will not start 1. No fuel in fuel tank. 2. Plug defective. 3. Plug connection defective. 4. Dirt in carburetor or fuel pipe. Start motor will not turn engine 1. Battery flat. 2. Poor contact between cable and battery pole.
79 Le moteur ne démarre pas 1. Manque d’essence dans le réservoir. 2. Bougie d’allumage défectueuse. 3. Raccord de bougie défectueux. 4. Impuretés dans le carburateur ou la canalisation de carburant Le démarreur n’entraîne pas le moteur 1.
80 NL 7. Ricerca guasti. 7. Het localiseren van fouten. Il motore non parte 1. Manca il carburante. 2. Difetto di candela. 3. Collegamento della candela difettoso. 4. Sporco nel sistema di alimentazione e o nel carburatore. Il motorino di avviamento non fa girare il motore 1.
81 8. Storage. 8. Aufbewahrung. 8. Rangement. 8. Conservación. The following steps should be taken when mowing season is over: • Clean the entire machine, especially underneath the cutting unit cover. • Touch up all chipped paint surfaces in order to avoid corrosion.
82 8. Rismessaggio. 8. Stallen. Aan het einde van elk maaisezoen moeten de volgende maatregelen worden genomen: • Maak de hele machine schoon, in het bijzonder de binnenkant van de kap van de maaikast. • Herstel lakbeschadigingen om roest te voorkomen.
83.
532 18 08-40 Rev. 1 02.14.02 RH Printed in U.S.A..
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il McCulloch 14592RB è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del McCulloch 14592RB - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso McCulloch 14592RB imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul McCulloch 14592RB ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il McCulloch 14592RB, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del McCulloch 14592RB.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il McCulloch 14592RB. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo McCulloch 14592RB insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
