Manuale d’uso / di manutenzione del prodotto NX-16 del fabbricante MaxTech
Vai alla pagina of 14
User's Guide NX-16 Series High Performance Software Configurable 16-bit ISA NE-2000 compatible Ethernet Adapters Part #MAN005 Rev. 1.1.
Please take a moment to note the following infor- mation. Include this form in the unlikly event that you need to return the product for warranty service. Refer to Section Eight for complete Warranty information and procedures on returning your product.
1 Contents Section One - Introduction ......................... 1 Section Two - Installation ........................... 2 Section Three - Driver Installation .............. 7 Section Four - Troubleshooting .................. 7 Section Five - Cable Information .
2 Minimum hardware requirements are an IBM PC/XT (or better) fully compatible PC with 512K RAM running DOS 3.3 or higher. The network operating system you use may have higher requirements. Section Two - Installation This section will provide step by step in- structions on how to install your new Maxtech network adapter.
3 2.2 Hardware Installation Installation of this adapter card requires opening and manipulating your PC. Exercise cau- tion at all times when working with AC powered and static-sensitive equipment. Turn off and un- plug your PC before installation. Discharge any static electricity from your body by touching any metal surface.
4 6. Carefully install the adapter by firmly press- ing the card into the slot you have chosen, applying even pressure until the adapter is completely seated in the slot. 7. Fasten the retaining bracket with the screw from the slot cover. Make sure the adapter is properly aligned.
5 Running the SETUP program 1. Insert the installation diskette into your drive, log on to that drive, and run the SETUP program in the DIAG subdirectory. Assuming that your have inserted the dis- kette in drive A, you would type the follow- ing at the DOS C: drive prompt: A: [ENTER] DIAGSETUP [ENTER] 2.
6 2.4 Testing The Adapter The SETUP program provides an option in its main menu for adapter diagnostics. One or more PCs on the network can run the test simulta- neously. The Test Adapter option runs several tests and the results are indicated by either PASS or FAIL.
7 sure that the notch on the ROM matches that on the socket (refer to Figure 2). 2. Configure the adapter using the SETUP program to enable the Boot ROM function by selecting the appropriate address from the Boot ROM Base Address option. Refer to Section 2.
8 README.TXT file describing the driver. Refer to the RELEASE.TXT file on the installation diskette for more information on the available drivers. Section Four - Troubleshooting This section describes some of the com- mon problems you may encounter while using your network adapter.
9 4.2 Cable Problems A) Observe the green Link Status LED if you are using a 10Base-T network. Turn on the computer. Connect the network cable and observe the green LINK LED. If the LED is ON, then the system is connected. Otherwise check for a proper RJ-45 connection.
10 must use solid copper conductors and UL codes CM, CMR, and CMP are required. The computer on the network is connected via a star topology (i.e. each node is connected to a HUB, not to each other). Maximum cable length is 300' (100 m). 10Base-2 networks uses a single conduc- tor coaxial cable and BNC connectors.
11 Section Seven - Technical Support In the unlikely event you experience difficulty in the use of the product, or if it does not operate as described, we suggest you: (1) consult the Troubleshooting section of this guide and (2) consult with your dealer.
12 (also enclose a check for out-of-warranty repair). En- close your check or Postal Money Order for $7.50 to cover the cost of return shipping/handling. Please do not send cash or stamps. 4. After wrapping the package securely for shipping, print your name, return address and the RMA # clearly on the outside of your package.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il MaxTech NX-16 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del MaxTech NX-16 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso MaxTech NX-16 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul MaxTech NX-16 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il MaxTech NX-16, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del MaxTech NX-16.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il MaxTech NX-16. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo MaxTech NX-16 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
