Manuale d’uso / di manutenzione del prodotto AF501 del fabbricante Makita
Vai alla pagina of 15
SPECIFICATIONS 4 - 7 kgf/cm2G 160 - 100 PSIG) L MODEL AF501 246 mm x 57 mm x 225 mm 1.26 kg 19-11/16'' x 2-114" x 8-718") 12 78 Ibs! 100 pcs. 6.5 25 mm, 30 mm, 35 mm. 40 mm. 45 mm, 50 mm (l", 1-3/16", 1-318". 1-9/16", 1-314".
IMPORTANT SAFETY INSTRUCTIONS WARNING: WHEN USING THIS TOOL, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF PERSONAL INJURY, INCLUDING THE FOLLOWING: f? READ ALL INSTRUCTIONS. For personal safety and proper operation and main- tenance of the tool, read this instruction manual carefully before using the tool.
General Tool Handling Guidelines: 1. Always assume that the tool contains fasteners. 2.Do not point the tool toward yourself or anyone whether it contains fasteners or not. 3. Never depress the operating control unless the nosepiece of the tool is directed toward the workpiece.
There may be local regulations concerning noise which must be complied with by keeping noise levels within prescribed limits. In certain cases, shutters should be used to contain noise. Do not tamper with the tool or attempt to use it for other than nailing.
Always check the tool for its overall condition and loose screws before operation. Tighten as required. Make sure the safety mechanism is in working order before operation.
Use only nails specified in this manual. The use of any other nails may cause malfunction of the tool. Do not permit those uninstructed to. use the tool. Make sure no one is nearby before nailing. Never attempt to nail from both the inside and outside at the same time.
On rooftops and other high locations, nail as you move forward. It is easy to lose your footing if you nail while inching backward. When nailing against perpendicular surface, nail from the top to the bottom. You can perform nailing operations with less fatigue by doing so.
*When the air hose is connected, do not carry the tool with your finger on the trigger or hand it to someone in this condition. Accidental firing can be extremely dangerous. Handle the tool carefully as there is high pressure inside the tool that can be dangerous if a crack is caused by rough handling (dropping or striking).
z" Perform cleaning and maintenance right after finish- ing the job. Keep the tool in tip-top condition. Lubricate moving parts to prevent rusting and minimize friction related wear. Wipe off all dust from the parts. When not operating the tool, always lock the trigger by turning the lock knob (lock pin).
TOOL INSTALLATION INSTRUCTIONS AND USE Lubrication To insure maximum performance, install an air set (oiler, regulator, air filter) as close as possible to the tool.
Load nails into the magazine so that the nail points will be set into the groove at the bottom of the maga- zine. Move the nails into the ejection slot as far as they will go. CAUTION : Always load the same type and size of nail into the magazine. If you load the tool with different types and/or sizes at the same time, a malfunction may result.
3. Loosen the three screws which secure the driver guide a half turn. 4. Turn the adjusting bolt until the desired depth of nailing can be obtained. The adjusting bolt moves 0.7 mm (1 /32") per turn. 5. Tighten the three screws while holding the driver guide so that the projection of the center plate contacts the adjusting bolt.
I I .i Connecting air hose Lock the trigger. Slip the air socket of the air hose onto the air fitting on the nailer. Be sure that the air socket locks firmly into position when installed onto the air fitting.
Hook The hook is convenient for hanging the tool tempo- rarily. This hook can be installed on either side of the tool. CAUTION : .Always lock the trigger and disconnect the hose when hanging the tool using the hook. Never hang the tool on a waist belt or the like.
I Check regularly to see if there is sufficient pneumatic oil in the oiler of the air set. Failure to maintain suffi- cient lubrication will cause O-ring to wear quickly. Keep the air hose away from heat (over 60°C, over 140” F), away from chemicals (thinner, strong acids or alkalis).
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Makita AF501 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Makita AF501 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Makita AF501 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Makita AF501 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Makita AF501, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Makita AF501.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Makita AF501. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Makita AF501 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
