Manuale d’uso / di manutenzione del prodotto 5016N8 del fabbricante Makita
Vai alla pagina of 22
Chain Saw MODEL 501 4NB 501 6N8 340 mm (13-3/8") MODEL 5014NB 375 mm (14-3/4") MODEL 5016NB Overall Net Chain speed Length of Saw chain Pitch Gauge length weight IFPM) guide bar 1,300 6 kg 340 mm 9.5 mm 1.27 mm 760 mm (1 3.318") 1318") (0.
IMPORTANT SAFETY INSTRUCTIONS WARNING: WHEN USING AN ELECTRIC CHAIN SAW, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO PERSONS, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5.
9. Use Safety Glasses Also use safety footwear; snug fitting clothing; protective gloves; hearing and head protection. Carry the chain saw by the front handle with the saw stopped, finger off the switch, the guide bar and saw chain to the rear. Inspect chain saw cords periodically and if damaged, have repaired by authorized service facility.
(1) Grip saw firmly. Hold the chain saw firmly with both hands when the motor is running. Use a firm grip with thumbs and fingers encircling the chain saw handles.
Use Of Extension Cord If the extension cord is intended to be used outdoors, the cord shall be marked with the suffix W-A following the cord type designation, for example - SJTW- A, to indicate it is acceptable for outdoor use. Use an extension cord heavy enough to carry the current the tool will draw.
Chain Saw Nomenclature LEFT SIDE Front handle v RIGHT Rear handle / Trigger switch SIDE Oil cap Guide bar nose I Guide bar mounting pad Sprocket Bar Tip Guard - An attachment that may be provided on the end of the guide bar to prevent the chain at the end of the guide bar from contacting the wood.
Front Handle Guard - A structural barrier between the front handle of a chain saw and the guide bar, typically located close to the hand position on the front handle and sometimes employed as an activating lever for a chain brake. Guide Bar - A solid railed structure that supports and guides the saw chain.
Installing saw chain and guide bar CAUTION : Always be sure that the tool is switched off and unplugged before installing saw chain and guide bar Use the socket wrench to loosen the hex bolt holding the chain cover. Remove the chain cover. 1 Fig. 2 Fit one end of the chain over the sprocket and the other over the end of the guide bar.
Adjusting saw chain tension CAUTION : Always be sure that the tool is switched off and unplugged before adjusting chain tension. Grasp the chain in the middle of the guide bar and lift up. The gap between the side link of the chain and the guide bar should be about 3 mm to 4 mm (1/8" - 5/32").
Lubrication This tool is equipped with an automatic lubrication system, so the chain is lubricated automatically when the motor is running. I Gear housing cover I Window To replenish the oil, take off the cap on the tank and fill with the oil supply.
Hook When using an extension cord, secure it to the tool’s cord with the hook provided. Attach the hook about 100-200 mm (4”- 8”) from the extension cord connector. This will help prevent unintentional dis- connection. Power cord Extension cord Fig.
To release the chain brake, reset the pro- tector to the exact original position after turning the tool off. Fig. 14 WARNING: 0 Under normal circumstances, it should never be necessary to intentionally release the chain brake while the tool is running.
Using the chain saw Always be sure of your footing and hold the chain saw firmly with both hands while the motor is running. Felling a tree When bucking and felling operations are being performed by t.
Felling back cut Limbing a tree Limbing is removing the branches from a fallen tree. When limbing, leave larger lower limbs to support the log off the ground. Remove the small limbs in one cut as shown in Fig. 18. Branches under tension should be cut from the bottom up to avoid binding the chain saw.
Bucking a log Bucking is cutting a log into lengths. It is important to make sure your footing is firm and your weight is evenly distributed on both feet. When possible, the log should be raised and supported by the use of limbs, logs or chocks. Follow the simple directions for easy cutting.
When bucking on a slope, always stand on the uphill side of the log, as shown in Fig. 22. When ”cutting through”, to maintain complete control, release the cutting pres- sure near the end of the cut without re- laxing your grip on the chain saw handles.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Filling saw chain To get the most in cutting performance from your tool, you must keep the cutter sharp and filed properly as shown below.
Removing chip buildup Chips and sawdust will build up in the guide bar groove and oil hole, clogging them and impairing oil flow. Remove the guide bar and clean them out. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark.
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
Aq-25438 US CHAIN SAW 340 mm (13-318") Model 5014NB 375 mm (14-3/47 Model 5016NB Note: The switch, noise suppressor and other part configurations may differ from country to country.
MODEL 5014NB 5016NB $:D DESCRIPTION 54 55 56 57 58 59 60 61 62 63 Aug - 25-'88 US $tD DESCRIPTION 1 6 1 I 1 2 1 2 1 1 lo 1 11 1 :: 1 ; 14 1 15 16 17 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 3.
MAKllA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Makita 5016N8 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Makita 5016N8 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Makita 5016N8 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Makita 5016N8 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Makita 5016N8, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Makita 5016N8.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Makita 5016N8. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Makita 5016N8 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
