Manuale d’uso / di manutenzione del prodotto LYNX L-210 L-210 del fabbricante Lynx
Vai alla pagina of 33
Web Interface User’s Guide ADSL Ethernet & USB Combo Router.
2 1. Intr oduction ................................................................................................................ .............. 3 1.1 Fea tures ........................................................................................
3 1. Introduction The Lynx L- 210 is the perf ect high- speed WAN bridge/rout er. This full-feature d product is specific ally designed to c onnect t o the Internet and direct ly connect to your local area net work vi a high speed 10/1 00 Mbps Etherne t.
4 Management Support • Web Based HTT P mana gement GUI • TFTP/FTP Support fo r Firmware Upgrade • Web Based F i rm ware Upgr ade (Local ) • Soft Factory Res et Button v ia Web GUI • Diagnost.
5 2. Your gateway at a glance The Lynx L-210 may have diff erent port s and LEDs . Let’s take a lo ok at the different opt ions. Depending u po n yo u r mod el, it may have some or all of t he features list ed below 2.
6 3. Installing your Lynx L-210 1 . Locate an optimum loc ation f or t he Lynx L-210. 2. For conn ec tions t o t he Ethe r net and DS L interfac es , please refer t o the easy s tart guide. 3. Connect the AC Power A dapter. Depe n ding upon t he type of net work, you may wa nt to put the power supply on a n uninterr uptibl e s upply.
7 4. Setting up your Lynx L-210 This section will guide you through your Lynx L-210’s configuration. The Lynx L-210 is shipped with a standar d PPP configurat ion. 4.1 Log into your Lynx L-210 To configu re your L ynx L-210, open y our web b rowser.
8 Figure 2 (Qui ck Start pag e ) 4.3 Setup (for advance user) From this s creen th e user can s etup th e Lynx L- 210 (config ure the LAN and WA N connect ion(s), configur e the advanced co nfiguratio.
9 4.3.1 Wide Area Network conne ct ion On the othe r side of t he Lynx L-21 0 is where you r Wide Area Net work (WAN) c onnecti on; also referred t o as a bro adband con nection. This WAN c onnection is diff erent for ever y WAN supplier. Most of the confi guration you will perform w ill be in this area.
10 To configu re the Lynx L-210 as a brid ge, click on Setup and then c lick on New Conne ction . The default PPP oE connecti on setup is displa yed. At the Type f ield selec t Bridge and the Bridge connect ion setup pa ge is displayed (s ee Figure 4).
11 service provider or your ISP will supply these; in this case the DSL servic e provider is using 0,100 . Also select the quality of service (QO S); leave the default v alue if you are u nsure or t he ISP did not provide t his inf ormation. Following is a des cription of the different opt ions: a.
12 To complete the connection you mu st now click the appl y button. The apply button will temporarily save this connection. To make the c hange perma nent you need to click on Save Setting (at the side of t he pa ge). At the s ystem commands pa ge, click on Save All .
13 Figure 6 (PPPOE Co nnection Setup) To complete the connection you mu st now click the appl y button. The apply button will temporarily save this connection. To make the c hange perma nent you need to click on Save Setting (at the side of t he pa ge ).
14 Figure 7 (DH CP Connec t ion Setup ) To complete the connection you mu st now click the appl y button. The apply button will temporarily save this connec tion. To make t he change permanent you need t o click on Save Settings (at the side of t he pa ge ).
15 Figure 8 (Static IP Connectio n Setup) To complete the connection you mu st now click the appl y button. The apply button will temporarily save this connec tion. To make t he change permanent you need t o click on Save Settings (at the side of t he pa ge ).
16 Figure 9 (CLI P Connect ion Setup) To complete the connection you mu st now click the appl y button. The apply button will temporarily save this connec tion. To make t he change permanent you need t o click on Save Settings (at the side of t he pa ge ).
17 second DHC P server into t he network, you will experience net work errors and the network will not functi on no rm ally. 4.5.1 Enable/Disable DHCP To enable or d isable DHCP, Click setu p. Under LAN Setup , select DHCP Configu ration. This will bring up the s creen s ho wn in F igure 10.
18 Figure 11 (Example of a DHCP Relay c onfiguration) By turning of f the DHCP serv er and relay the net w ork adminis trator must c arefully configure the IP address , Subnet M ask an d DNS set tings of every c omputer o n your n etwork.
19 Figure 12 (M anageme nt IP address ) The apply button will temporar ily save this connectio n. To make th e change permanen t you need to click on Save Settings (at the si de of the page).
20 Figure 13 (M an a gement IP ad dress) The apply button will temporar ily save this connectio n. To make th e change permanen t you need to click on Save Settings (at the si de of the page).
21 Figure 13 (P o r t Forwardin g : Netmeet ing) The apply button will temporar ily save this connectio n. To make th e change permanen t you need to click on Save Settings (at the si de of the page). At the s ys tem commands pag e, click on Save All .
22 The apply button will temporar ily save this connectio n. To make th e change permanen t you need to click on Save Settings (at the si de of the page).
23 through t he bridge based o n source MA C address , destinat ion MAC addr ess and/ or frame t ype. When bridge filtering is enabled, each frame is examined against the de fined filter rules sequenti ally, and when a matched is d etermined, the a ppropriat e filtering ac tion (determi ned by th e access ty pe selecte d .
24 ARP frames t hrough th e system. The second r ule allows all IPv4 fram es with th e destinat ion MAC address of the bri dge to go t hrough. T he third r ule allo ws all IPv4 fram es with t he sourc e MAC address of the bridge t o go throug h. Note: On a wind o ws based mac hine, to find a MAC addres s , at a dos prompt t ype ipconfig /all .
25 4.6.8 Static Routing If the Ly nx L-210 is connec ted to more t han one ne twork, you may need t o set up a static ro ute betwee n them . A stat ic rout e is a pr e-def ined pat hway t hat netwo rk inform ation must trav el to r each a specific host or net work.
26 will only send out RIP informat ion. Selecting both means that the Lynx L-210 w ill incorporate received RIP inform ation and send o ut upd at ed RIP informat io n. The prot ocol is depe ndent upon t he entire n etwork. Most networ ks support Rip v1.
27 4.7.2 User Management You can change your Lynx L-210’s username and passw ord by clicking on User Manage ment. From here yo u can cha nge the login name and pas sword. You can also c hange th e idle timeo ut; you will need to log back onto t he Ly nx L-210 once the t imeout expires.
28 default D HCP conf igurati on, you sh ould b e able to Ping th e network address 1 92.168. 1.1. If your ISP has prov ided their ser ver addres s you can try t o ping the a ddress . If the pings f or both th e WAN and the LA N side compl ete, and you have the pr oper prot ocols conf igured, you s hould be able to surf th e Inte rnet.
29 4.8.3 DHCP Clients Select to view t he list of DHCP c lients. 4.8.4 Modem Status Select t o vi ew t he Stat us and S tatist i cs of your broadb a nd ( DSL) connec tion. 4.8.5 Product Information You can d isplay the Lynx L-210’s driver and run -time information b y going under Statu s title and click on Product Inform ation.
30 5. Appendix A: Troubleshooting Below is a list of commonly asked quest ions. Before calling tec hnical support, please look thro ugh these iss ues to see if they help t o solve your probl em. 5.1 The Lynx L-210 is not functional 1. Chec k to see t hat the po wer LED is green a nd than the network c ables ar e installed correctly .
31 5.4 The DSL Link LED is always off 1. Make sure you hav e DSL servic e. You should get s ome kind of informat ion from your I SP that stat es that DSL s ervice is inst alled. You can us ually tell if t he service is inst alled by listening to th e phone line; you will hear s ome high-pitc hed noise.
32 6. Lynx L-210 terms What is a firewall? A firewall is p rotect ion betwe en the Int ernet and you r local net work. It acts similarly to t he firewall i n your car, prot ecting t he int erior of the car from t he engine.
33 One of t he c onf igur at ion pa ram et ers t ra ns mit t ed t o ea c h net work d ev ic e is its de f ault g at ewa y . T his address is configu red by t he net work administ rators and it informs.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Lynx LYNX L-210 L-210 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Lynx LYNX L-210 L-210 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Lynx LYNX L-210 L-210 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Lynx LYNX L-210 L-210 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Lynx LYNX L-210 L-210, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Lynx LYNX L-210 L-210.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Lynx LYNX L-210 L-210. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Lynx LYNX L-210 L-210 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
