Manuale d’uso / di manutenzione del prodotto C/A210 del fabbricante Logitek Standard Elec. Cable Manufacturing
Vai alla pagina of 18
INST ALLA TION AND OPERA TION MANUAL W ARNINGS • Hot! Do not touch! The glass and surfaces of this appliance will be hot during operation and will retain heat for a while after shutting off the appliance. Severe burns may result. • Carefully supervise children in the same room as appliance.
2 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. C ontents t esting i nforma tion .........................................................................3 g eneral s afety P reCautions .........................................................
3 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. t esting i nforma tion This manual describes the installation and operation of the Performer™ C/A210 non-catalytic wood heaters. These heaters meet the U.S. Environmental Protection Agency’ s emissions limits for wood heaters sold on or after July 1, 1990.
4 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. D rafting Y our wood stove is dependent upon a properly functioning chimney for optimum per formance. It is a high efficiency appliance that loses much less heat up the chimney than older applian ces and firep laces.
5 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Please be patient with the heat output of your stove for the first few weeks. The steel will go throu gh a curing process that eliminates moisture, which is deep in the steel and firebrick. This moisture will reduce initial heat output of your stove and may make it difficult to start.
6 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. B riCk i nst alla tion P erformer ™ C/a210 B riCk i nst allation CAUTION: Wear gloves during brick installation in case of sharp edges behind the stove.
7 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Model F (1) G H J(2) M C/A210 18” 45 0m m 12-1/4” 31 1m m 19 ” 48 3m m 4-1/2” 1 14m m 42 -1 /8 ” 10 70 m m C/A210 w/ mantel and/or sid.
8 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. C himney r equirements The Performer™ C/A210 inserts are approved for use in masonry fireplaces built to UBC Chapter 37 or equivalent with a minimum 22” (559mm) opening at the front of the fireplace.
9 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. i nst alla tion P roCeDure - f aCtor y -B uil t Z ero C learanCe f irePlaCes Fireplace and Chimney Requirements The Performer™ C/A210 insert m.
10 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Chimney Liner Installation Remove the existing chimney cap and install a stainless steel liner into the chimney (if a special section has been used or drilled to attach to the insert, it must be the bottom piece).
11 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. o Pera ting h ints 1. Burn only dr y , well-seasoned wood for maxi- mum heat output. In some states it is illegal to burn wet wood or anything other than clean, dry wood products.
12 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. s t arting anD m aint aining a f ire Be sure to clean the Nickel or Gold Plated door with Win- dex brand cleaner and a ver y soft cloth to remove any fingerprints and residues prior to the first fire.
13 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Keeping freshly loaded wood away from the window will also help. Load fresh logs in the rear of the firebox. Build-up tends to occur first on the right side of the window . This is caused by the swirling motion of the exhaust gases similar to water running down a drain.
14 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 4. Operate your stove as much as possible in the low to medium burn ranges. 5. Do not lower the draft setting so low as to compl etely extinguish the flames in the firebox. Check for at least some small flames 20 minutes after setting the draft control.
15 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Exp eri men t with diff ere nt loa din g config ura tio ns to achi eve longer burns. T r y loading the wood from side to side and nesting it in the ashes to prevent airflow under and around the wood.
16 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. t rouBleshooting Problem Solution POOR DRAFT : Extend chimney in length or have the chimney realigned to the proper size flue. Oversized chimneys normally have poor drafts. Remember , the stoves’ draft depend solely on the natural draft of the chimney (See Drafting section on page 4).
17 D o ’ s anD D on ’ ts DO NOT : Install or operate this stove before reading this manual. DO NOT : Close the draft beyond the point at which the flames are completely extinguished. DO NOT : Open the stove door without fully opening the draft first.
The manufacturer reser ves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. 1110 West T aft Avenue • Orange, CA 92865 Printed in U.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Logitek Standard Elec. Cable Manufacturing C/A210 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Logitek Standard Elec. Cable Manufacturing C/A210 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Logitek Standard Elec. Cable Manufacturing C/A210 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Logitek Standard Elec. Cable Manufacturing C/A210 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Logitek Standard Elec. Cable Manufacturing C/A210, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Logitek Standard Elec. Cable Manufacturing C/A210.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Logitek Standard Elec. Cable Manufacturing C/A210. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Logitek Standard Elec. Cable Manufacturing C/A210 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
