Manuale d’uso / di manutenzione del prodotto PSUS4 del fabbricante Linksys
Vai alla pagina of 58
A Division of Cisco Systems, Inc . ® Model No . WIRED with 4-Port Switch PrintServ er for USB PSUS4 User Guide.
PrintServer for USB with 4-P ort Switch Copyright and T rademarks Specifications are subject to change without notice . L inksys is a registered tradema rk or trademark of Cisco Systems, Inc . and/or its affiliates in the U.S . and certain other countries.
PrintServer for USB with 4-P ort Switch Table of Contents Chapter 1: Introduction 1 Welcome 1 What’s in this Guide? 1 Chapter 2: Getting to Know the USB PrintServer 4 The Back Panel 4 The Front Pane.
PrintServer for USB with 4-P ort Switch Common Problems and Solutions 37 Appendix B: About Bi-Directional Printing 39 Appendix C: Upgrading Firmware 40 Appendix D: Windows Help 41 Appendix E: Glossary.
PrintServer for USB with 4-P ort Switch List of Figures Figure 2-1: USB PrintServer’s Back Panel 4 Figure 2-2: The USB PrintServer’s Front Panel 5 Figure 2-3: The USB PrintServer’s Side Panel 5 .
PrintServer for USB with 4-P ort Switch Figure 5-2: Driver’s Welcome 12 Figure 5-3: Choose Destination Location 12 Figure 5-4: Select Program Folder 13 Figure 5-5: Copy Folder 13 Figure 5-6: Setup C.
PrintServer for USB with 4-P ort Switch Figure 8-6: Connected Protocol 29 Figure 8-7: Searching for Device 29 Figure 8-8: Setup Complete 29 Figure 8-9: Bi-Admin Management Utility 30 Figure 8-10: Devi.
1 Chapter 1: Introductio n Welcome PrintServer for USB with 4-P ort Switch Chapter 1: Introduction We l c o m e Thank you for choosing the Linksys PrintSer ver for USB with 4-Port Switch (PrintServer). The PrintServe r will allow you to network your printers.
2 Chapter 1: Introductio n What’s in this Guide? PrintServer for USB with 4-P ort Switch • Chapter 4: Installing the PrintSer ver using the Setup Wizard This chapter instructs you on how to use t he Setup Wizard to install your PrintSer ver .
3 Chapter 1: Introductio n What’s in this Guide? PrintServer for USB with 4-P ort Switch • Appendix I: Regulatory Infor mation This appendix supplies the regulator y information regarding the PrintServer .
4 Chapter 2: Getting to Know the USB PrintServer The Back Panel PrintServer for USB with 4-P ort Switch Chapter 2: Getting to Know the USB PrintSer ver The Back P anel The USB PrintServer's ports, where the cables are connecte d, are located on the back panel.
5 Chapter 2: Getting to Know the USB PrintServer The Front Panel PrintServer for USB with 4-P ort Switch The Front P anel The PrintServer's LEDs, where informa tion about network activity is displayed, are located on the front panel. Status Green.
6 Chapter 3: Connecting the PrintServer Overview PrintServer for USB with 4-P ort Switch Chapter 3: Connecting the PrintSer ver Overview Before starting the physical installation, make a note of the PrintServer’s Default Name that is located on the bottom of the PrintServer .
7 Chapter 4: Installing the PrintServer u sing the Setup Wizard Installation PrintServer for USB with 4-P ort Switch Chapter 4: Installing the PrintSer ver using the Setup Wizard Installation 1. T o begin installation of the PrintSer ver , you will use the Setup CD-ROM to run the Setup Wizard.
8 Chapter 4: Installing the PrintServer u sing the Setup Wizard Installation PrintServer for USB with 4-P ort Switch 6. The Password screen, Figure 4-4, will appear next. Enter the default password ad min in the field. Click Enter . 7. The Basic Settings screen, shown in Figure 4-5, will appear .
9 Chapter 4: Installing the PrintServer u sing the Setup Wizard Installation PrintServer for USB with 4-P ort Switch 8. The IP Settings screen, Figure 4-6, appears next. If your network uses a router wi th a DHCP Internet Protocol setting that automatically assigns an IP address, select Automatically obtain an IP address (DHCP) .
10 Chapter 4: Installing the PrintServer u sing the Setup Wizard Installation PrintServer for USB with 4-P ort Switch 10. The Confirmation screen appears next. See Figure 4-8. Y our old and new settings will be displayed. If you want to make a change , click No and you will exit the Setup Wizard; Y ou will have to start the Setup Wizard again.
11 Chapter 5: Windows Driver Installation Overview PrintServer for USB with 4-P ort Switch Chapter 5: Windows Driver Installation Overview This section installs the PrintSer ver’s softw are on your Windows 98, Me , 2000, or XP computers to give them PrintServer printing abilities.
12 Chapter 5: Windows Driver Installation Installation PrintServer for USB with 4-P ort Switch 3. The Welcome screen of the driver installation progra m, Figure 5-2, will appear first. Y ou will need to close any other programs you have open before you continue .
13 Chapter 5: Windows Driver Installation Installation PrintServer for USB with 4-P ort Switch 5. The next screen to appear is Select Program Folder , shown in Figure 5-4. An icon will be added to the program folder listed. Y ou may chan ge the name for the program folder , if you wish.
14 Chapter 5: Windows Driver Installation Installation PrintServer for USB with 4-P ort Switch 8. The Information screen appears next. See Figure 5-7. Read the info rmation, then click OK . 9. The Printer Port Setup screen will appear , as shown in Figure 5-8, and list the PrintServer and the connected printers.
15 Chapter 5: Windows Driver Installation Installation PrintServer for USB with 4-P ort Switch 11. The Configure Printer Port screen will appear , as sh own in Figure 5-10. Y our installed printer will appear in the field. Click the Connect button to connect the printer for conf iguration.
16 Chapter 6: Configuring the PrintServe r Overview PrintServer for USB with 4-P ort Switch Chapter 6: Configuring the PrintSer ver Overview The PrintServer has been designed to be fun ctional right out of the box with the default settings in the Setup Wizard.
17 Chapter 6: Configuring the PrintServe r The Protocol Tab - TCP/IP PrintServer for USB with 4-P ort Switch The Protocol T ab - TCP/IP Click the TCP/IP tab to view or change the TC P/IP values of the PrintSer ver . (See Figure 6-2.) IP Address . If you are using DHCP to assign IP addresses, select Obtain an IP Address Automatically .
18 Chapter 6: Configuring the PrintServe r The Protocol Tab - TCP/IP PrintServer for USB with 4-P ort Switch The Protocol T ab - NetBEUI NetBEUI connection settings of the PrintSer ver are available on this tab . (See Figure 6-4.) Domain Name . Enter the name of the domain that you want the PrintSer ver associated with in the Domain Na me field.
19 Chapter 6: Configuring the PrintServe r The Printer Tab - Internet Printin g PrintServer for USB with 4-P ort Switch The Printer T ab - Internet Printing Internet Printing allows you to automatically print any e-mails that are sent to a sp ecific e-mail account on your network.
20 Chapter 6: Configuring the PrintServe r The Printer Tab - Internet Printin g PrintServer for USB with 4-P ort Switch The Printer T ab - Logical P ort The Logical Printers tab contains the logical printer settings of the PrintServer . Select from th e following fields for each Logical Printer .
21 Chapter 6: Configuring the PrintServe r The Printer Tab - Internet Printin g PrintServer for USB with 4-P ort Switch The Status T ab - Device The Device tab allows you to view information abou t the PrintSer ver . No values can be changed on this screen.
22 Chapter 6: Configuring the PrintServe r The Printer Tab - Internet Printin g PrintServer for USB with 4-P ort Switch The Exit T ab This tab is used exclusively for exiting the Web-based Utility . (See Figure 6-9.) Select the Exit tab and the scr ee n in Figure 6-9 will appear .
23 Chapter 7: Internet Printing Prot ocol Overview PrintServer for USB with 4-P ort Switch Chapter 7: Internet Printing Protocol Overview Internet Printing Protocol (IPP) is a new standards-based system to allow remote printing from a PC to any accessible printer .
24 Chapter 7: Internet Printing Prot ocol Windows IPP Client Setup PrintServer for USB with 4-P ort Switch 2. If Internet access from your location is via a Proxy Ser ver , check Access IPP Server via P roxy Server , and enter details of your Proxy Ser ver .
25 Chapter 7: Internet Printing Prot ocol Windows IPP Client Setup PrintServer for USB with 4-P ort Switch • Retr y Interval sets the time inter val (in seconds) between connection attempts. Increase this number if you have a poor connection, or the remote ser ver is ver y busy .
26 Chapter 7: Internet Printing Prot ocol Windows IPP Client Setup PrintServer for USB with 4-P ort Switch • It is powered off . • A printer problem has caused the IPP Ser ver to cease responding, and a restart (reboot) is required. • The Ser ver’s IP Address has c hanged.
27 PrintServer for USB with 4-P ort Switch Chapter 8: Bi-Admin Man agement Overview Chapter 8: Bi-Admin Manag ement Overview The PrintServer is managed by a utility program called Bi-Adm in on the PrintSer ver’s Setup CD .
28 PrintServer for USB with 4-P ort Switch Chapter 8: Bi-Admin Man agement Bi-Admin Installation 4. The next screen to appear is Choose Destination Location, as shown in Figure 8-3. Y ou will be requested to choose the location of where the Bi-Admin folder will be installed.
29 PrintServer for USB with 4-P ort Switch Chapter 8: Bi-Admin Man agement Starting the Bi-Admin Manag ement Utility Starting the Bi-Admin Management Utility 1. T o start the Bi-Admin program, click on Start , Progr ams , Print Server Utility , and then Bi-Admin Management Utilit y , as shown in Figure 8-6.
30 PrintServer for USB with 4-P ort Switch Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility The Bi-Admin Management Utility The Bi-Admin Management Utility screen will appear n ext. Any hardware found on the network will appear on the left-hand side of the screen, a s shown in Figure 8-9.
31 PrintServer for USB with 4-P ort Switch Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility • Printer Status . This op tion allows you to view the printer status, and set port and printer parameters. If you click this option, a Verify Passwor d screen will appe ar , as shown in Figure 8-11.
32 PrintServer for USB with 4-P ort Switch Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility • Configuration . Y o u may configure the PrintServer with this opt ion. If you click this option, a Verify Password screen will appear , as shown in Figure 8-14.
33 PrintServer for USB with 4-P ort Switch Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility TCP/IP If you are using DHCP to assign IP addresses, select Dynamic IP Address (DHCP) . (See Figure 8-16.) By default, Dynamic IP Address (DHCP) is enabled.
34 PrintServer for USB with 4-P ort Switch Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility Apple T alk (Figure 8-18) AppleT alk is a network communications protocol that allows computers to talk to each other using Eth ernet.
35 PrintServer for USB with 4-P ort Switch Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility Interne t Printin g (Figure 8-20) Enter the address of your mail ser ver in the Mail Ser ver IP Address fields. (This value must be a fixed IP address.
36 PrintServer for USB with 4-P ort Switch Chapter 8: Bi-Admin Man agement The Bi-Admin Managem ent Utility If you click Attached Remote , the screen in Figure 8-22 appears. T o add a cross segment print ser ver , enter the IP address in the fields, and click the Set button.
37 Appendix A: Common Problems and So lutions PrintServer for USB with 4-P ort Switch Appendix A: T roubleshooting This appendix consists of “Common Problems and Solution s”. Provided are possible solutions to problems th at may occur during the installation and operation of the Print Ser ver .
38 Appendix A: Common Problems and So lutions PrintServer for USB with 4-P ort Switch 6. The Confi guratio n button o n the Printer Status scr een in Bi-Admin is gra yed out, even though my printer is bi-dir ectional. The button is unavailable until the printer has finished its print jobs and sits idle .
39 Appendix B: About Bi- Directional Printing PrintServer for USB with 4-P ort Switch Appendix B: About Bi-Directional Printing Normal printing only sends print signals from a PC to a pr inter .
40 Appendix C: Upgradin g Firmware PrintServer for USB with 4-P ort Switch Appendix C: Upgrading Firmware The PrintServer's firm ware is upgraded through the Bi-Admin Management utility . Follow these instructions: 1. Download the firmware from Linksys's website at www .
41 Appendi x D: Wind ows Hel p PrintServer for USB with 4-P ort Switch Appendix D: Windows Help All wireless products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier .
42 Appendix E: Glossary PrintServer for USB with 4-P ort Switch Appendix E: Glossar y 802.11a - An IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps and an operating frequency of 5GHz.
43 Appendix E: Glossary PrintServer for USB with 4-P ort Switch Buffer - A block of memor y that temporarily holds data to be worked on later when a device is currently too busy to accept the data. Cable Modem - A device that con nects a computer to the cable television network, which in turn connects to the Internet.
44 Appendix E: Glossary PrintServer for USB with 4-P ort Switch Dynamic IP Address - A temporar y IP address assigned by a DHCP server . Encryption - Encoding data to prevent it from being read by unauthorized people . Ethernet - An IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium.
45 Appendix E: Glossary PrintServer for USB with 4-P ort Switch IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device. IPSec (Internet Pro tocol Security) - A VPN protocol used to implem ent secure exchange of packets at the IP layer .
46 Appendix E: Glossary PrintServer for USB with 4-P ort Switch PPP oE (Point to Point Proto col over Ethernet) - A type of broadband connection that provides authentication (username and password) in addition to data transport.
47 Appendix E: Glossary PrintServer for USB with 4-P ort Switch TCP/IP (T ransmission Control Protocol/Inter net Protocol) - A network protocol fo r transmitting data that requires acknowledgement from the recipient of data sent. Te l n e t - A user command and TCP/IP protocol used for accessing remote PCs.
48 Appendix F: Specifications PrintServer for USB with 4-P ort Switch Appendix F: Specifications Standards IEEE 802.3, 802.3u, USB 1.0/1.1 Ports/Buttons 4 10/100 RJ-45 Ports Auto MDI/MDI-X, Reset Cabling T ype Category 5 or better , and USB 1.1 cable with T ype-B female and T ype-A male connectors LEDs Status, USB , 1-4 Dimensions 3.
49 Appendix G: Warranty Information PrintServer for USB with 4-P ort Switch Appendix G: W arranty Information LIMITED WARRANTY Linksys warrants to the original end user purchaser ("Y ou") th.
50 Appendix H: Regulatory Inf ormation PrintServer for USB with 4-P ort Switch Appendix H: Regulator y Information FCC ST A TEMENT This PrintServer for USB with 4-Port Switch has been tested and complies with the specifications for a Class B digital device , pursuant to Part 15 of the FCC Rules.
51 Appendix I: Contact Informa tion PrintServer for USB with 4-P ort Switch Appendix I: Contact Information Need to contact Linksys? Visit us online for information on the latest products and updates to your existing products at: http://www .linksys.com or ftp.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Linksys PSUS4 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Linksys PSUS4 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Linksys PSUS4 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Linksys PSUS4 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Linksys PSUS4, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Linksys PSUS4.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Linksys PSUS4. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Linksys PSUS4 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
