Manuale d’uso / di manutenzione del prodotto J-S del fabbricante Linear
Vai alla pagina of 26
I N S T A L L A T I O N A N D OWNER’S MANUA L As of date of manufacture, meets all ANSI/UL 325 Safety Requirements for V e h i c u l a r d o o r o p e r a t o r s J-S & H-S J & H SERIES WITH.
REA D THESE STA TEMENTS CAREFUL LY AND FOLLOW T HE INSTRUCT IONS CLOSELY. The Warning and Caution boxes throughout this manual are there to protect you and your equipment. Pay close attention to these boxes as you follow the ma nual. WARNING Indicates a MEC HANICAL hazard of INJUR Y OR DEATH.
The purpose of this booklet is to prov ide assem bly, installation and operat ion inf ormation concerning Mo del J -S & H-S Comm ercial Vehicular Garage Door Operators and related Accessor y Products. NOTICE IT IS IMPORTA NT TH AT THIS INSTRU CTION MANUA L BE READ AND UN DERSTOOD COMPLETE LY BEFORE INSTA LL AT ION OR OPERA TION IS ATTE MPTED.
Before starting the installatio n of the operator , the door must be in good working condition and p roper ly counterbalanced. Inspec t the door and trac k for loose or missing hardware. T est the door manually for balance and ea se of oper ation. Lubricate door hinges and rollers.
COMPONENT IDENTIF IC A TION LISTIN G ITEM PART # DESCRIPTION QTY ITEM PART # DESCRIPTION QTY 1 Per M odel Operator Power Head 1 8 009 149 Release Chain AR 2 005031 3 Button St ation 1 9 100315 #3 Hand.
SPRINGS, PULLEYS, CA BLES AND MOUNTING H ARDWARE USED TO BALANCE YOUR GARA GE DOOR ARE UNDER EXTREME TENSION A T ALL TIMES AND CAN CAUSE SEVERE INJURY OR DEA TH IF DISTURBED. DO NOT ATTEMPT ADJUSTMENT. F igure 6, page 8 illu strates several positions suitable for mounting the operator ; right hand or left hand, either wall mo unt or ceiling mount.
CHAIN HOIST AND F LOOR DISCONNECT INSTALLATION If the operator is furnished with a chain hoist (Mo del H -S), pass t he hand chain over the chain wheel and through the c hain guides on the operator clutch shaft ( opposite end from the lar ge pulley).
Figure 6 100719 Right Side Mount Ceiling Mount Left Side Mount Ceiling Mount Center Mount Direct Couple W all Mount W all Mount 8 FIGURE 4 - OPE R A TOR MOUNT ING POSITIONS.
107841 Figure 7 - Dimensions Model H-S Figure 7A - Dimensions Model J-S 108203 9 FIGURE 5 - OPE RA TOR DIMENSIONS - MODEL J-S & H-S.
4) Depress the limit nut retaini ng Plate (D) so it disengages from the slots in the limit nut s. Turn the OPEN limit nut (E) on the shaft until it engage s the Open Limit S witch (A). You will need to listen for an audib le click. Release t he retaining plate and be sure that it engage s in slots of bo th limit nuts.
RISK OF ENT R APMENT THAT MAY RESULT IN SERIOUS PERS ONAL INJUR Y OR DEATH. DISC ONNECT PO WER TO THE OPENER BE FORE AND DUR ING INSTA LLATION OF AN ACCESSORY REVERS ING DOOR EDGE OR PHOTOELE CTRIC DEVICE. DO NOT RECONNE CT POWER T O OPENER U NT IL IN ST RU CT ED T O D O S O.
9. See Figure 16 for connecting the photoelectric device to the operator . See Page 15 for prop er setting of the selector switches. These switches must be proper ly set and an approved p hotoelectric device o r approved door edge device connected to the oper ator to obtain B2 Mode of Operation, Mo mentary Contact to Close.
MOTOR CONTROL BOARD Figure 9 OPEN TB1 STOP CLOSE OPEN COM CLOSE STOP NO REV NC REV PHOTO COM SINGLE ILOCK 24 VAC COM SAFE FINISH PHOTOBEAM 3-WIRE PHOTOBEAM Door Edge and Photoelectric Wiring After properly connecting a n appro ved Entrapment Protection Device (see above and Page 3 ) to the operator, see Page 15 for setting of the selector switches.
NOTE: It is now necessary to turn on the pow er in order to change the Operating Mo de (if applicable), progra m any changes des ired to the operator’s ot her settings, c heck for pr oper performanc.
AVOID ELECTROCUTION: DO NOT ROUTE LOW VOLTAGE WIRES IN SAME CONDUIT AS HIGH VOLTAGE WIRES. FOLLOW ALL LOCAL ELECTRICAL CODES OR THE NAT IONAL ELECTRICAL CODE. WARNING FAILURE TO TEST REVERSING SYSTEM COULD RESULT IN DEATH OR SERIOUS INJURY. TEST THIS SYSTEM ONCE A MONTH.
Changing the S witch Selectable Opera tion Modes The following modes are selected b y setting the on -board dip switches, Figure 14 at right sho ws where the switches are located on the o perator control b oard. For each Oper ational Mode, the switches are set to either ON or OFF ac cording to the table at right belo w.
Mid -Stop : Activation stops an op ening door; momentary con tact of open button at mid stop will restart d oor to full open position; if door is moving open, constant pressure on open button will bypass mid -stop. Auto Close Timer : N/ A TS Operation Open Button : Momentary activation; op en override of closi ng door.
The solenoid operated brake may require occasiona l adjustment. Adj ustment is necessary i f door tends to drift downward after reaching the op en limit. Follo w the instructions belo w and use Figure 15 as a guide. (1) Loosen shoe adj usting screw and bottom bracket ar m of solenoid.
CLUTCH A DJU STMENT The clutch serves to pr otect the do or, the electric operato r and other equipment from undue s tress or damage caused by starting forces and/or an obstructio n to the door. It should be set no tighter than is necessar y to smoothly and consiste ntly move the door throughout its full ra nge of travel.
OPERA TI ON & ADJUSTME NT INSTRUCTI ONS 20.
Following installation, the op erator MUST be tested and respond correc tly to all controls as specified on the wiri ng diagram. KEEP per sonnel and equip ment clear of the area beneath the door when performing the tests.
WIRING DI AGRA M/S CHEM A TIC - SIN GLE PHASE 22 575 VOL TS, 3 PHASE SINGLE VOL T AGE MOTOR BL/BLK BL/BLK TO REVE RSE MOTOR, SWITCH LEADS 1 & 3 L1 4 L2 YELLOW WHITE BLACK ORANGE BLUE RED Wire Nut Conn ection 3 BLUE (T ,J,H) YELLOW BLUE RED BLACK A.
575 VOL TS, 3 PHASE SINGLE VOL T AGE MOTOR BL/BLK BL/BLK TO REVE RSE MOTOR, SWITCH LEADS 1 & 3 L1 4 L2 YELLOW WHITE BLACK ORANGE BLUE RED Wire Nut Conn ection 3 BLUE (T ,J,H) YELLOW BLUE RED BLACK A.
24 NOTES.
Ref P art# Description Assemblies A 105933 Fram e Asse mbly w/Shafts. J 109318 Frame Asse mbly w/Shafts, H C 106501 Drive Shaft As sembly, J/H D 105930 Disconnect Sha ft Assembly, J 105206 Intermediat.
26 SPECIFICATIONS MODEL : J_ _ _ _S HP:_____ VOLTS : _____ PHASE : _____ * UL AND CANADIAN UL LISTED * HIGH STARTING TORQUE, CONTINUOUS DUTY MOTOR * MOTOR OVERLOAD PROTECTIO N * CLASS 2 (24 VOLT) CONT.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Linear J-S è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Linear J-S - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Linear J-S imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Linear J-S ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Linear J-S, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Linear J-S.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Linear J-S. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Linear J-S insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
