Manuale d’uso / di manutenzione del prodotto 663 del fabbricante Life Fitness
Vai alla pagina of 19
1 663 660 SECOND ST ACK OPTION CLASS H PAR T # 7050101 REV . C Revision: 07/31/01 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product.
THERE IS A RISK ASSU MED BY IND IVIDUALS W HO USE T HI S TYPE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THESE RULE S ! 1. Before u sing, read al l the w arnings and in structions on the use of this mach ine. Use only for in tended exercise. DO NOT mo dify the m achine.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody 663 660 Second Stack Option. Please read these instructions thoroughly and keep them for future reference. 3 NOTE: BOL T LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOL T .
STEP 2 FIGURE 2 FIGURE 1 STEP 1 • REMOVE the four 3/8” X 1” BUTTON HEAD CAP SCREWS from the top of the front SHROUD & rear SHROUD. See FIGURE 1.
STEP 3 FIGURE 3 5 • Unscrew the threaded ends of the HEAD PLA TE CABLE from the WEIGHT ST ACK SHAFT & the D-RING and remove HEAD PLA TE CABLE. The HEAD PLA TE CABLE will be used later .
6 PRESS CABLE (67249) STEP 4 • Remove the PRESS CABLE (67249) from the KEYHOLE CLEVIS and ELASTIC CORD. (NOTE: The LA T or LEG EXT CABLE can be moved over one hole on the D-RING so the KEYHOLE CLEVIS are evenly spaced .) FIGURE 4 ELASTIC CORD D-RING KEYHOLE CLEVIS • Discard the KEYHOLE CLEVIS and ELASTIC CORD.
7 STEP 6 FIGURE 6 • Assemble the previously removed 2” PULLEY to the bracket on the TOP BOOM using one 3/8 X 1” BOL T (1 1), one previously remov ed 3/8” W ASHER, and one previously removed 3/8” LOCK NUT . See FIGURE 6. • (NOTE: STEP 6 is only completed if the 100101 LEG PRESS OPTION is installed otherwise proceed to STEP 7.
FIGURE 8 STEP 8 • Discard the two 3/8 X 1/2” SP ACERS. • Remove two 2” PULLEYS to the rear bracket on the T OP BOOM using one 3/8” THREADED SHAFT , two 3/8” W ASHERS, two 3/8” HEX NUTS, and two 3/8” LOCK NUTS as shown in FIGURE 8. FIGURE 9 STEP 9 • Position the elastic cords over the 2” PULLEYS as shown in FIGURE 9.
STEP 10 • Carefully remove and discard the PRESS CABLE as shown in FIGURE 10. PRESS CABLE (67249) FIGURE 10 9 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2.
10 STEP 1 1 • Route the new PRESS-ST ACK CABLE (5) around the pulleys and l-brackets as shown in STEP 11. (Remove pulleys for ease of installation.) 5 5 FIGURE 1 1 FIGURE 12 STEP 12 PRESS-ST ACK CAB.
FIGURE 14 STEP 14 • LOOSEN the bolts holding the TOP BOOM to the UPRIGHTS. Bolts will have to be removed to install GUIDE RODS (1). See FIGURE 14. 11 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 LOOSEN! TOP BOOM LOOSEN! STEP 13 • Snap two WEIGHT PLA TE BUSHINGS (17) each, into the “ top” side of fifteen WEIGHT PLA TES (16) as shown in FIGURE 13.
FIGURE 15 STEP 15 • Insert two GUIDE RODS (1) into the BASE as shown on FIGURE 15. (NOTE: Lubricate GUIDE RODS (1) with silicon or teflon spray available at most hardware stores.) • Slide two WEIGHT ST ACK SP ACERS (3), two 3/4” W ASHERS (15), and two WEIGHT ST ACK CUSHIONS (8) - IN THA T ORDER - down over the GUIDE RODS (1).
STEP 16 FIGURE 16 13 • W ith the GUIDE RODS (1) securely held in the T OP BOOM. Tighten all TOP BOOM connections. (NOTE: Make sur e the LA T CABLE runs over the top of the bolts in the TOP BOOM.) 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 TIGHTEN! ( NOTE: Make sure LA T CABLE runs over top of bolts in TOP BOOM.
14 HEAD PLA TE CABLE (7041801) STEP 17 FIGURE 17 • Screw one of the threaded ends of the previously removed HEAD PLA TE CABLE approximately 1” into the end of the WEIGHT ST ACK SHAFT . See FIGURE 17. WEIGHT ST ACK SHAFT STEP 18 • Screw the other threaded end of the HEAD PLA TE CABLE approximately 1” into the end of the shaft on the D-RING.
STEP 19 FIGURE 19 15 REAR SHROUD • The rear SHROUD opening must be removed. Apply pressure to the bottom of the SHROUD where the “V” groove is and carefuly remove the weight stack opening on the plastic SHROUD as shown in FIGURE 19.
STEP 21 FIGURE 21 FIGURE 20 STEP 20 • SECUREL Y attach the four previously removed 3/8” X 1” BUTTON HEAD CAP SCREWS from the top of the front SHROUD & rear SHROUD.
MAINTENANCE MODEL #________________________ SERIAL #_________________________ DA TE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 17 * W e recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water .
18 NOTES: LIMITED W ARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The W arranty terms apply to IN HOME USE ONL Y . 1. LIMITED W ARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repair ed or replaced by ParaBody .
INTERNA TIONAL OFFICES LifeFitnessAtlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 LifeFitness Japan 8/F , Nippon Brunswick Building 5-27-7 Sendagaya Shibuya-Ku, T okyo 151-0051 Japan Phone: 81 (3) 3359-4309 Fax: 81 (3) 3359-4307 LifeFitness (UK) Ltd.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Life Fitness 663 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Life Fitness 663 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Life Fitness 663 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Life Fitness 663 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Life Fitness 663, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Life Fitness 663.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Life Fitness 663. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Life Fitness 663 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
