Manuale d’uso / di manutenzione del prodotto MU-42PZ44MK del fabbricante LG Electronics
Vai alla pagina of 36
PLASMA MONIT OR OWNER’S MANUAL Please read this owner ’s manual carefully before operating the Monitor . Retain it for future reference. Record model number and serial number of the Monitor . See the label attached on the back of the Monitor and quote this information to your dealer when you require service.
2 Warning W ARNING : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE P ARTS INSIDE. REFER T O QUALIFIED SERVICE PERSONNEL.
3 Safety Instructions Important safeguards for you and your new product Y our product has been manufactured and tested with your safety in mind. However , improper use can result in potential elec- trical shock or fire hazards.
4 Safety Instructions Antenna Lead in Wire Antenna Discharge Unit (NEC Section 810-20) Grounding Conductor (NEC Section 810-21) Ground Clamps Po wer Service Grounding Electrode System (NEC Art 250, Pa.
5 Contents After reading this manual, keep it handy for future reference. W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4 Introduction Controls and Connection Options .
6 Introduction Introduction Introduction What is a Plasma Display Panel (PDP)? If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.
7 Introduction Controls Controls Connection Options Connection Options R ( ) ( ) ( ) ( ) L EXP ANDED INPUT VIDEO INPUT RS-232C INPUT (CONTROL/SERVICE) EXTERNAL SPEAKER YP B P R (MONO) R AUDIO L R AUDIO L S-VIDEO AC INPUT AUDIO INPUT AUDIO INPUT AUDIO INPUT REMOTE CONTROL COMPONENT INPUT DVI INPUT RGB INPUT RGB OUTPUT 1 1.
8 Introduction Remote Control Key Functions Remote Control Key Functions - When using the remote control, aim it at the remote control sensor on the monitor . - Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function.
9 Installation Installation Installation D-sub 15 pin Cable Owner ’ s Manual 1.5V 1.5V Batteries BNC-RCA Adapter Power Cord 123 456 78 0 9 POWER SLEEP INPUT SELECT APC DASP ARC PIP ARC PIP TWIN PICTURE SWAP MENU MUTE OK VOL POWER STOP PLAY FF REC REW P/STILL WIN.
10 Installation W W all Mount: V all Mount: V ertical installation (MU-42PZ44M/44V/90M/90V series models only) ertical installation (MU-42PZ44M/44V/90M/90V series models only) Detailed installation instructions are included in the optional V ertical W all Mounting Bracket Installation and Setup Guide, see your dealer .
11 Installation External Equipment Connections External Equipment Connections NOTE: All cables shown are not included with the plasma display . - T o avoid picture noise (interference), leave an adequate distance between the VCR and Monitor - Use the ISM Method feature to avoid having a fixed image remain on the screen for a long period of time.
12 Installation • Component Input ports T o get better picture quality , connect a DVD player to the compo- nent input ports as shown below . - T o watch digitally broadcast programs, purchase and connect a digital set-top box. - This monitor supports HDCP (High-bandwidth Digital Contents Protection) protocol for DTV (480p,720p,1080i) modes.
13 Installation How to connect 1. T o get the best picture quality , adjust the PC graphics card to 800x600, 60Hz. 2. Use the monitor ’ s RGB INPUT or DVI (Digital Visual Interface) INPUT port for video connections, depending on your PC connector .
14 Installation Resolution 640x350 720x400 640x480 848x480 852x480 Horizontal Frequency(KHz) 31.468 37.861 31.469 37.927 31.469 35.000 37.861 37.500 43.269 31.500 35.00 37.500 31.500 35.000 37.500 70.09 85.08 70.08 85.03 59.94 66.66 72.80 75.00 85.00 60.
15 Operation T urning on the Monitor just after installation T urning on the Monitor (power cord is still connected) 1. Connect power cord correctly . 2. Press the ON/OFF button on the Monitor . At this moment, the Monitor is switched to standby mode.
16 Operation - Each adjustment for the Picture menu options doesn ’ t effect other input sources. Readjust Picture menu options for each of the following sources.
17 Operation 1. Press the DASP button repeatedly to select the appropriate sound setup as shown below . DASP DASP (Digital (Digital Auto Sound Processing) Auto Sound Processing) 1. Press the MENU button and then use D / E button to select the SOUND menu.
18 Operation - T imer functions operate only if current time has been set. - Off-T imer function overrides On-T imer function if they are set to the same time. - The monitor must be in standby mode for the On-T imer to work. On/Of On/Of f f T T imers Setup imers Setup 1.
19 Key Lock Key Lock - The monitor can be set up so that it can only be used with the remote control. - This feature can be used to prevent unauthorized viewing by disabling the front panel controls. - This Monitor is programmed to remember which option it was last set to even if you turn the monitor off.
20 Special Menu Options continued Special Menu Options continued SPECIAL Prev. Language Key lock ISM Method Low power Set ID Caption / T ext Captions OSD Rotate G Normal Rotate SPECIAL MENU 1. Press the MENU button and then use D / E button to select the SPECIAL menu.
21 Operation Auto Auto Adjustment Adjustment - RGB (PC) mode only; This function doesn ’ t work for RGB-DTV mode. - Automatically adjusts picture position and minimizes image shaking. - After adjustment, if the image is still not correct, your Monitor is functioning properly but needs further adjustment.
22 Adjusting Horizontal/ V Adjusting Horizontal/ V ertical Position ertical Position 1. Press the MENU button and then use D / E button to select the SCREEN menu. 2. Press the G button and then use D / E button to select Position . 3. Press the G button and then use D / E / F / G button to adjust the position.
23 Operation Split Zoom Split Zoom - Enlarges the picture in correct proportions. - Split Zoom can be used for all input sources. - In 2-Split Zoom mode, you can only move the image up or down. - If an image is enlarged, a section can be viewed without using Split Zoom.
24 - PIP lets you view 2 different inputs pictures (sources) on your monitor screen at the same time. One source will be large, and the other source will show a smaller inset image. - Y ou can also adjust the PIP features in the PIP/DW menu (Except Swap function).
25 Operation - As the name suggests, this mode splits the screen into 2, allowing 2 picture sources to be shown on the monitor screen at the same time.
26 No. Pin name 1 No connection 2 RXD (Receive data) 3 TXD (T ransmit data) 4 DTR (DTE side ready) 5 GND 6 DSR (DCE side ready) 7 RTS (Ready to send) 8 CTS (Clear to send) 9 No Connection 1 5 6 9 2 3 .
27 External Control Device Setup Set ID Set ID Use this function to specify a monitor ID number . Refer to ‘ Real Data Mapping 1 ’ . See page 28. • Baud rate : 1 15200 bps (UART) • Data length : 8 bits • Parity : None * Use a crossed (reverse) cable.
28 External Control Device Setup 02. Input Select (Command2:b) (Main Picture Input) G T o select input source for the Monitor. Y ou can also select an input source using the INPUT SELECT button on the Monitor's remote control.
29 External Control Device Setup 09. Color (Command2:i) G T o adjust the screen color. Y ou can also adjust color in the Picture menu. T ransmission Data Min : 0 ~ Max : 64 • Refer to ‘ Real data mapping 1 ’ . See page 28. [k][i][ ][Set ID][ ][Data][Cr] Acknowledgement [i][ ][Set ID][ ][OK][Data][x] 10.
30 External Control Device Setup 22. Red Adjustment (Command2:v) G T o adjust red in color temperature. T ransmission Data Min: 0 ~ Max: C8 • Refer to ‘ Real data mapping 3 ’ as shown below . [k][v][ ][Set ID][ ][Data][Cr] Acknowledgement [v][ ][Set ID][ ][OK][Data][x] 23.
31 External Control Device Setup 27. ISM Method (Command2:p) G T o avoid having a fixed image remain on screen. T ransmission Data 0: Normal 1: White wash 2: Orbiter 3: Inversion [j][p][ ][Set ID][ ][Data][Cr] Acknowledgement [p][ ][Set ID][ ][OK][Data][x] 28.
32 G Connect your wired remote control to the Remote Control port on the Monitor . G Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz G Configuration of frame G Repeat code G Le.
33 IR Code 00H 01H 02H 03H 08H C4H C5H 09H 10H 11 H 12H 13H 14H 15H 16H 17H 18H 19H 0BH 98H D5H C6H BFH 5AH D8H 0EH 44H 43H 52H 4DH 60H 61H 63H 64H 6BH 40H 41H 69H 6AH 7BH 79H 76H 77H AFH 99H R/C Butt.
34 T roubleshooting Checklist No output from one of the speakers • Adjust Balance in the SOUND menu. (Refer to p.17) Unusual sound from inside the monitor • A change in ambient humidity or temperature may result in an unusual noise when the plasma display is turned on or of f and does not indicate a fault with the monitor .
35 Maintenance & Specification 1. Here ’ s a great way to keep the dust of f your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it ’ s almost dry , and then use it to wipe the screen.
PLASMA MONIT OR OWNER’S MANUAL Please read this owner ’s manual carefully before operating the Monitor . Retain it for future reference. Record model number and serial number of the Monitor . See the label attached on the back of the Monitor and quote this information to your dealer when you require service.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il LG Electronics MU-42PZ44MK è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del LG Electronics MU-42PZ44MK - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso LG Electronics MU-42PZ44MK imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul LG Electronics MU-42PZ44MK ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il LG Electronics MU-42PZ44MK, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del LG Electronics MU-42PZ44MK.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il LG Electronics MU-42PZ44MK. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo LG Electronics MU-42PZ44MK insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
