Manuale d’uso / di manutenzione del prodotto OPTIX-10OPTIX-10 del fabbricante Lanzar Car Audio
Vai alla pagina of 18
www .lanzar .com 10-Channel Active Electronic Crossover Network with Subwoofer Level Control user’s manual OptiX -1 0 OptiX -1 0.
Congratulations on your purchase of a new Lanzar Opti signal processor . Opti mobile electronics are some of the most advanced car audio products available. These quality audio products are designed and engineered to afford you years of uncompromising musical service.
general features precautions features and specifications system wiring mounting and installation noise check and system adjustment troubleshooting 2 3 4-6 7-11 12-13 14 15 table of contents.
10 Crossover Channels Blue Light Illumination 4 Channel Inputs Signal Pass-through for Additional Processors Remote Bass Level Control High Channels: Separate Front and Rear Frequency and Gain Control.
3 Precautions T o prevent short circuits, be sure to disconnect the negative battery ground lead before wiring the system up. When you finish the installation, be sure to make one more check to be sure everything is done correctly . Reinstate all car parts that were removed.
4 featur es and specifications.
5 featur es and specifications 1. F/R INPUT SWITCH 2. FRONT & REAR CHANNEL MID CUT Q SELECTORS 3. FRONT & REAR CHANNEL MID CUT CONTROLS 4. Front & Rear Channel High-P ass Phase Inverters 5. Front Frequency & Gain Controls 6. Rear Frequency & Gain Controls 7.
6 featur es and specifications Crossover Frequencies -Front High-Pass -Front Mid High-Pass -Front Mid Low-Pass -Rear High-Pass -Rear Mid High-Pass -Rear Mid Low-Pass Crossover Slope Rate Subwoofer Boost Boost Frequency Mid Cut Mid Cut Q: Distortion Frequency Response Signal-to-Noise Ratio (A) Separation Power Source Dimensions 1.
7 System wiring 2-CHANNEL 3 WA Y SYSTEM REAR CHANNEL Speakers FRONT CHANNEL Speakers Head unit (Stereo, DVD Player , T ape Deck, etc.) TO REAR OUTPUT TO SUB OUTPUT to REMOTE OUTPUT from HEAD UNIT BA T.
8 System wiring 2-CHANNEL MUL TIPLE CROSSOVER SYSTEM TO REAR MID OUT TO SUB OUTPUT Head unit (Stereo, DVD Player , T ape Deck, etc.) SUBWOOFER Speakers REAR MID-WOOFER Speakers TO FRONT MID OUT TO REA.
9 TO SUB OUTPUT TWEETER Speakers SUBWOOFER Speakers TO FRONT MID OUT TO REAR HIGH OUT TO FRONT HIGH OUT GROUND BA TTERY MID-WOOFER Speakers WOOFER Speakers UPPER MIDRANGE Speakers (to REMOTE OUTPUT fr.
10 System wiring BA TTERY TO FRONT HIGH OUT 4 CHANNEL 4 WA Y SYSTEM TO REAR MID OUT TO SUB OUTPUT to REMOTE OUTPUT from HEAD UNIT GROUND SUBWOOFER Speakers FRONT TWEETER Speakers REAR MID-WOOFER Speak.
11 System wiring 6-CHANNEL 5-WA Y SYSTEM FRONT TWEETER Speakers TO REAR MID OUT TO SUB OUTPUT Head unit (Stereo, DVD Player , T ape Deck, etc.) to REMOTE OUTPUT from HEAD UNIT SUBWOOFER Speakers FRONT.
12 Mounting and installation Y our new Opti Series crossover comes complete with all required mounting hardware. Please read the Installation Precautions section below before installing your Lanzar Op.
13 Mounting and installation • Solder -less connectors or soldering gun with heat shrink tubing 1. Find a suitable location in the vehicle to mount the processor . The X-10 is a trunk mount unit and it should be installed in close proximity to your amplifier system on the amp rack.
NOISE CHECK Check the entire audio system for noise before permanently securing the CROSSOVER mounting 1. Start the engine. 2. T urn the audio system on. 3. Rev the engine and vary the VOLUME of the audio system to determine if there is any unwanted noise.
1. There is an audible distortion at a low volume level. PROBLEM POSSIBLE CAUSE • Output levels NOT set correctly . • Crossover frequencies NOT set correctly . • Check for shorts on the speaker leads. 2. A whining sound can be heard through the speakers when the audio system is at low volume with the engine running.
All Lanzar Signal Processors are carefully constructed and thoroughly tested before shipment. Units purchased in the USA are warranted to be free of defects in material and workmanship for three (3) years from the date of purchase. This warranty is limited to the original retail purchaser of the Signal Processor .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Lanzar Car Audio OPTIX-10OPTIX-10 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Lanzar Car Audio OPTIX-10OPTIX-10 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Lanzar Car Audio OPTIX-10OPTIX-10 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Lanzar Car Audio OPTIX-10OPTIX-10 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Lanzar Car Audio OPTIX-10OPTIX-10, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Lanzar Car Audio OPTIX-10OPTIX-10.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Lanzar Car Audio OPTIX-10OPTIX-10. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Lanzar Car Audio OPTIX-10OPTIX-10 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
