Manuale d’uso / di manutenzione del prodotto 15 del fabbricante Lanzar
Vai alla pagina of 16
www .lanzar .com user’s manual OptiE-15 OptiE-15 15-Band Half/Full Octave Stereo Equalizer.
Congratulations on your purchase of a new Lanzar Opti signal processor . Opti mobile electronics are some of the most advanced car audio products available. These quality audio products are designed and engineered to afford you years of uncompromising musical service.
general features precautions features and specifications system wiring mounting and installation noise check and system adjustment troubleshooting 2 3 4-5 6-9 10-11 12 13 table of contents.
15 Band Equalizer Controls per Channel in 1/2 and Full Octave Steps Blue Light Illumination ± 12 dB Boost/Cut at Each Frequency Setting Front, Rear and Line Outputs Separate Front, Rear and Line Outp.
3 Precautions T o prevent short circuits, be sure to disconnect the negative battery ground lead before wiring the system up. When you finish the installation, be sure to make one more check to be sure everything is done correctly . Reinstate all car parts that were removed.
4 featur es and specifications.
5 featur es and specifications Control Frequencies Half Octave Full Octave Control Range Frequency Response Signal-to-Noise Ratio (A-Wtd) Input Sensitivity Maximum Output Voltage Channel Separation Power Requirement Dimensions, WxDxH, inches (millimeters) 20Hz • 30Hz • 45Hz • 67Hz 100Hz • 150Hz • 200Hz 350Hz • 500Hz • 800Hz 1.
6 System wiring Standard 4-Channel Output For standard 4-channel operation, plug both the left and right RCA outputs from your head unit into the E-15 inputs. The output power can be distributed to either the front or rear speakers by using the fader control.
7 System wiring Dual E-15 2 + 2 Channel Output Using 4 RCA Inputs T wo Model E-15s are required for this configuration. For more exact control, the E-15s can be configured into separate mono units with the outputs summing the signal into stereo.
8 System wiring Dual E-15 2 + 2 Channel Output Using 2 RCA INPUTS T wo Model E-15s are required for this configuration. If your head unit has only one pair of RCA output jacks, you can achieve the same result by using a pair of Y -adapter cables. Utilizing two E-15s permits the users to tailor 4 separate 15 band channels in full stereo.
9 4 Channel Output Using Speaker Level Inputs If your radio does not have RCA outputs, as is the case with most standard OEM radios, you can use the speaker outputs from those head units to supply audio signal to the E-15.
10 Mounting and installation Y our new Opti Series Octave Equalizer comes complete with all required mounting hardware. Please read the Installation Precautions section below before installing your La.
11 Mounting and installation (q y g y pp ) • Solder -less connectors or soldering gun with heat shrink tubing 1. Find a suitable location in the vehicle to mount the processor . The E-15 is a trunk mount unit and it should be installed in close proximity to your amplifier system.
NOISE CHECK Check the entire audio system for noise before permanently securing the EQUALIZER mounting 1. Start the engine. 2. T urn the audio system on. 3. Rev the engine and vary the VOLUME of the audio system to determine if there is any unwanted noise.
1. There is an audible distortion at a low volume level. PROBLEM POSSIBLE CAUSE • Output levels NOT set correctly . • EQUALIZER frequencies NOT set correctly . • Check for shorts on the speaker leads. 2. A whining sound can be heard through the speakers when the audio system is at low volume with the engine running.
All Lanzar Signal Processors are carefully constructed and thoroughly tested before shipment. Units purchased in the USA are warranted to be free of defects in material and workmanship for three (3) years from the date of purchase. This warranty is limited to the original retail purchaser of the Sig nal Processor .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Lanzar 15 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Lanzar 15 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Lanzar 15 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Lanzar 15 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Lanzar 15, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Lanzar 15.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Lanzar 15. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Lanzar 15 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
