Manuale d’uso / di manutenzione del prodotto HT200 del fabbricante Knoll Systems
Vai alla pagina of 30
HT200 Users Manual v1.0 Complies with part 15 of the FCC rules. Operation is subject to: 1. This device may not cause harmful interference 2. This device must accept any interference received including interference that may cause undesired operation.
IMPORTANT SAFEGUARDS These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them carefully and heed all warnings.
Table of Contents 2 IMPORTANT SAFETY INFORMATION 3 Table of contents 4 Basic information 5 Features 5 Remote control 6 Terminal connections 7 Projector part identification 8 Projector positioning 9 Co.
Basic HT200 Information Congratulations On Your Purchase of the HT200 Projector! The HT200 is one of the very best Projectors available today. The HT200 enables you to project precise images up to 300.
Remote Control Inserting the batteries 1) Press firmly and slide the battery cover off. 2) Insert the supplied two batteries (size AA/R6). Ensure that the polarities (+ and -_) of the batteries are aligned correctly. Always replace batteries with fresh alkaline type.
Terminal Connection Panel Projector Part Identification 6.
Installation The distance from the projector lens to the screen determines to the size of the projected image, therefore, you need to consider the place where you set up the projector and screen before making connections. You also need to consider the screen size and height of the unit and screen as other important factors.
Use the following information to position the projector. Horizontally the projector needs to be positions with the lens-centered left to right Projection Distance 4:3 Video Screen Distance to Screen 47" 83" 122" 165" 210" 415" 485" Screen Diag.
Connecting Video Equipment You can connect a document camera, VCR, laser disc player, and DVD player, etc. Connecting to the VIDEO IN VIDEO/S-VIDEO JACKS You can connect up to two pieces of video equipment to the VIDEO IN jacks following the illustration below.
Connecting Component Video Equipment withYCbCr output jacks to the RGB IN connector You can also connect the video component to the RGB IN connector, if the video component has the component video (YCbCr) signal jacks. This connection may provide a better picture quality than the connections on page 9.
Connecting a PC or Macintosh Connecting a PC or Macint osh to the Projector enables com puter images for im pressive presentati ons. • The following display standards are supported: VGA 640x480 for .
Modifying the DIP switch (for Macintosh) setting Modify the DIP switch setting on the MAC cable as shown below. Macintosh adapter cable DIP switch setting (o=ON) MONITOR RESOLUTION 1 2 3 4 5 6 Multipl.
Connecting the remote mouse receiver to an IBM PC/AT computer Connect the IBM/Mac connector on the remote mouse receiver and PC's mouse port with the supplied serial cable. Connecting the remote mouse receiver to an IBM PS/2 or Macintosh computer Connect the supplied serial cable to the IBM/ Mac connector on the remote mouse receiver.
2) Press the POWER ON button on the remote control or the POWER button on top of the unit to turn on the unit. The POWER indicator on top of the unit turns to green and start blinking. It will take one minute for the projector to be ready to use . Wait until the indicator stops blinking and lights steadily in green.
7) Change the unit setting to suit to the pr ojecting method and selected source as described in step 4. • Select the type of projection If the projected image is horizontally reversed or upside down, change the projection type.
Changing computer's video resolutions Depending on your computer's graphic capability, you may be able to select one of several resolutions. Generally a computer- either a PC or Macintosh- with 1 MB VRAM will run: 640 x 480 at 16.7 million colors (24 bit True color) 800 x 600 at 65,000 colors.
Adjusting the volume of the projector speaker Press VOLUME + to increase the volume or - to decrease. The volume can also be adjusted with the menu operation (see page 24). Using the laser pointer You can highlight the desired point on the screen with the beamed red light.
Menu operation- Selecting the input source with the remote 1) Press MENU. The button lights in red and the main me nu appears on the screen. If you don't proceed to step 2 within ten seconds, the button goes off. Note: The menu will not be displayed if the picture is enlarged even slightly.
of the selected menu item. value of the selected menu item. Selecting the projection type; Floor, Ceiling, Rear and Front This reorients your image for your type of projection. 1. Press MENU to display the main menu. 2. Press the cursor up or down key to select "SETTING MENU.
Setting "INPUT MODE" to "YCbCr" or Component Video When you have connected the component vide o (YCbCr) signal output jacks of the video component to the RGB IN connector on the unit (see page 10), set "IMAGE MODE" to "YCbCr" to obtain better picture quality.
Timing Chart Signal Resolution H. Sync. (kHz) V. Sync. (Hz) Dot Clock (MHz) 1 NTSC 640 x 480 15.734 59.94 - 2 PAL 768 x 576 15.625 50 - 3 SECAM 768 x 576 15.625 50 - 4 VESA 640 x 350 37.86 85.08 31.5 5 Mac 640 x 400 35 66 30.24 6 IBM 640 X 400 31.47 70 25.
Adjusting the clock frequency (PICTURE ADJ) and clock phase (FINE PICTURE) manually When "AUTO PICTURE" is set to "ON," the cl ock frequency and clock phase will be adjusted automatically.
Storing the most recent “PICTURE ADJ,” “FINE PICTURE,” “H POSITION,” AND “V POSITION” settings You can store the above present settings in the memory. CUSTOM 1 to 5. 1. Select the input source RGB (see page 13). 2. Press MENU to display the main menu.
Adjusting the picture elements The picture elements such as brightness, contr ast, white balance, and so on can be adjusted individually for each input source. The adjustab le items vary depending on the input source and “INPUT MODE” setting (see page 20).
The following three types of gamma modes can be selected according to your preferences: • NORMAL, • NATURAL 1, or • NATURAL 2. 8. Press L-CLICK. 9. Press the cursor up or down key to select “INP UT MODE,” then press the cursor +/- key to select the input mode.
Turning the projector off with on screen functions With the remote control: Press the POWER OFF button a for 2 seconds (the projector will turn off regardless of the “POWER OFF” setting) With the projector keypad: (When “DISPLAY” is set to “ON”) Press the POWER button.
Specifications Optical DMD TM Single Chip Digital Micro Device (DMD TM), 800x600 dots Lens Manual zoom, manual focus F3.0 f =27.5 to 35.75m m Lamp Metal halide lamp 280W Image Size 610 to 7620mm (24 to 300 inches) diagonal Projection Distance 1.2 to 12.
Troubleshooting This section helps you resolve problems while setting up or using your projector. Common Problems & Solutions Problem Check These Items Does not turn on Check that the cord is plugged in and that the power switch on the back panel is on.
When the STATUS indicator on the projector keypad lights or blinks Status Light Message Condition Status OFF Normal On Continually The projector lamp has exceeded 1000 hours of operation and should be replaced. Blinking Very Rapidly (On and off in a cycle of 1 sec.
Lamp housing replacement procedure 1. Switch off the m ain power and unplug the power cord. 2. Wait at least one hour for the lam p to cool. 3. Turn the unit upside down carefully . 4. Loosen the lamp cover securing screw. 5. Slide the lamp cover in the direction of the arrow and remove it.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Knoll Systems HT200 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Knoll Systems HT200 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Knoll Systems HT200 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Knoll Systems HT200 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Knoll Systems HT200, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Knoll Systems HT200.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Knoll Systems HT200. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Knoll Systems HT200 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
