Manuale d’uso / di manutenzione del prodotto TK-270G del fabbricante Kenwood
Vai alla pagina of 35
INSTRUCTION MANUAL MODE D’EMPLOI MANUAL DE INSTRUCCIONES BEDIENUNGSANLEITUNG MANUAL DI ISTRUZIONI GEBRUIKSAANWIJZING A 3 2 1 B 6 5 4 C 9 8 7 D 0 KENWOOD CORPORA TION © B62-1294-30 (E,NE,NT) 09 08 0.
TK-270G/ TK-370G VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER INSTRUCTION MANUAL ENGLISH.
i W ARNING: EXPLOSIVE A TMOSPHERES (GASES, DUST , FUMES, etc.) T urn off your transceiver while taking on fuel, or while parked in gasoline service stations. ◆ GOVERNMENT LAW PROHIBITS THE OPERA TION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE TERRITORIES UNDER GOVERNMENT CONTROL.
ii PRECAUTIONS Observe the following precautions to prevent fire, personal injury , and transceiver damage. • Do not modify this transceiver for any reason. • Do not expose the transceiver to long periods of direct sunlight, nor place it close to heating appliances.
iii CONTENTS UNP ACKING AND CHECKING EQUIPMENT ................... 1 Supplied Accessories ...................................... 1 PREP ARATION .................................................. 3 Charging the Optional NiCd Battery Pack ..............
iv Storing DTMF Numbers .................................... 1 6 Confirming Stored DTMF Numbers ..................... 16 Dialling Stored DTMF Numbers ......................... 17 Clearing Stored DTMF Numbers .......................... 1 7 Redialling .
1 UNP ACKING AND CHECKING EQUIPMENT Note: The following unpacking instructions are for use by your KENWOOD dealer , an authorized KENWOOD service facility , or the factory . Carefully unpack the transceiver . We recommend that you identify the items listed in the following table before discarding the packing material.
2 Belt clip Speaker/ microphone jacks cap Screw set Speaker/ microphone locking bracket Antenna (TK-270G) Antenna (TK-370G).
3 PREP ARA TION ■ Charging the Optional NiCd Battery Pack The optional battery pack is not charged at the factory; charge it before use (refer to the battery pack instruction manual). ◆ DO NOT RECHARGE THE BA TTER Y P ACK IF IT IS ALREADY FULL Y CHARGED.
4 1 Match the four grooves of the battery pack with the corresponding guides on the back of the transceiver . 2 Slide the battery pack along the back of the transceiver until the release latch on the base of the transceiver locks. 3 To remove the battery pack, pull back on the release latch and slide the pack away from the transceiver .
5 ■ Installing the Belt Clip If necessary , attach the belt clip using the two supplied 3 x 8 mm screws. Note: If the belt clip is not installed, its mounting location may get hot during continuous transmission or when left sitting in a hot environment.
6 A 3 2 1 B 6 5 4 C 9 8 7 D 0 GETTING ACQUAINTED q q q q q e e e e e r r r r r t t t t t y y y y y u u u u u i i i i i o o o o o !0 !0 !0 !0 !0 w w w w w Antenna Microphone Speaker The transceiver is shown with the optional KNB-14 battery pack.
7 e e e e e Power switch/ V olume control T urn clockwise to switch ON the transceiver . Rotate to adjust the volume. T o switch OFF the transceiver , turn counterclockwise fully . r r r r r PTT (Push-to-T alk) switch Press this switch, then speak into the microphone to call a station.
8 n o c I n o i t p i r c s e D . r e v i e c s n a r t s i h t n o d e s u t o N s i l e n n a h c d e t c e l e s e h t n e h w s r a e p p A . y s u b , e n o T - 2 , F M T D , T Q D , T Q n e h w s r a e p p A y b ( d e t a v i t c a e d s i g n i d o c e d e n o T - 5 r o e h t g n i s s e r p r o t i n o M .
9 PROGRAMMABLE AUXILIAR Y FUNCTIONS Side 1 , Side 2 , O , ● , t t t t t , and s s s s s can be programmed with the auxiliary functions listed below .
10 OPERA TING BASICS ■ Switching Power ON/OFF T urn the Power switch/ V olume control clockwise to switch the transceiver ON. T urn the Power switch/ V olume control counter- clockwise to switch the transceiver OFF . If the Radio Password function is programmed, “P ASSWORD” will appear on the display when the power is turned ON.
11 ■ Adjusting the Squelch Level Squelch is used to silence the speaker when no signals are present. When squelch is turned OFF , you will hear background noise from the speaker . When it is ON, you will not hear background noise. The squelch level you select determines when squelch will turn OFF and ON.
12 ■ Placing a Call 1 Make sure no parties are currently transmitting on your selected channel. 2 Press the PTT switch and speak into the microphone in your normal speaking voice. • For best sound quality at the receiving station, hold the microphone approximately 1.
13 CHANNEL SCAN Scan is useful for monitoring signals on the channels programmed on the transceiver . When scanning, the transceiver checks for a signal on each channel, and only stops on a channel if a signal is present. The transceiver will remain on a busy channel until the signal is no longer present.
14 ■ Priority Scan If your dealer set up a priority channel on your transceiver , the transceiver will continuously monitor that channel while receiving a signal on another channel. When a signal is received on the Priority channel, the transceiver immediately switches to that channel.
15 DTMF CALLS ■ Manual Dialling There are two ways to manually call a number: 1) Press and hold the PTT switch, then enter the desired digits on the keypad. •Y ou can enter the digits 0 ~ 9 , A ~ D , , and # . ( A ~ D may be disabled by your dealer .
16 ■ Storing DTMF Numbers Note: Auto Dialling must first be activated by your dealer . Y ou can store DTMF numbers (16 digits maximum) in each of the 9 Auto Dial memory locations (1 ~ 9). 1 Press the # key . • “D” appears on the display . 2 Enter the desired digits on the keypad.
17 ■ Dialling Stored DTMF Numbers To call a number stored in a memory location: 1 Press the key . • “A” appears on the display . 2 Enter the desired memory location number ( 1 ~ 9 ) . • The stored digits are displayed. 3 Press the PTT switch.
18 CODE SQUELCH Code Squelch is enabled or disabled by your dealer . This function turns the transceiver squelch OFF only when it receives the DTMF code that has been set up in your transceiver . T ransceivers that do not transmit the correct code will not be heard.
19 ■ T ransmitting 1 Press and hold the PTT switch. 2 Enter the code of the transceiver you want to call or enter a Group code on the keypad. • If desired, you can send codes the same way you make DTMF calls {page 15}. Both manual methods can be used or you can store codes in memory , then dial them from a memory location.
20 SELECTIVE CALL Selective Call is enabled or disabled by your dealer . This function is similar to Code Squelch {page 18}. The differences from Code Squelch are: •Y ou can send or receive message codes containing a maximum of 5 digits.
21 ■ Receiving When you receive the correct ID and Intermediate codes, squelch turns OFF and you will hear the call. If a message code is also received, the message appears on the display • “CALL” appears on the display and the LED indicator flashes orange.
22 ■ T ransmitting 1 Press and hold the PTT switch. 2 Enter the code of the transceiver you want to call or enter a Group code on the keypad. • Be sure to enter the ID or Group code, followed by the Intermediate code of the transceiver you want to call.
23 2-TONE SIGNALLING 2-T one Signalling is enabled or disabled by your dealer . This function turns the transceiver optional signalling OFF only when it receives the 2-tone signal that has been set up in your transceiver . T ransceivers that do not transmit the correct tones will not be heard.
24 ■ T ransmitting 1 Press the key programmed as 2-T one Encode . •A 2-T one code appears on the display . 2 Rotate the Rotary encoder to select your desired 2-T one code. 3 Press the PTT switch and 2-T one Encode key to begin transmitting. Release the 2-T one Encode key when transmission has started.
25 5-TONE SIGNALLING 5-T one Signalling is either activated or deactivated by your dealer . 5-T one Signalling only opens the squelch when the transceiver receives five tones corresponding to those set up in your transceiver . When the squelch opens, you will be able to hear the caller without any further action.
26 AUXILIARY FUNCTIONS ■ Selecting an Output Power Each channel is programmed with either high or low output power by your dealer . Y ou can change the output power of only channels programmed as high. When you can reliably communicate with other parties without using high power , select low power by pressing the key programmed as RF Power Lo .
27 ■ Busy Channel Lockout (BCL) The Busy Channel Lockout feature is activated or deactivated by your dealer . When activated, BCL prevents you from interfering with other parties who may be using the same channel that you selected.
28 ■ Battery Voltage Level While transmitting, the transceiver automatically checks the battery voltage level. When the voltage level becomes low , the LED indicator flashes red. When a tone sounds, transmission stops. Recharge or replace the battery pack at this time.
29 ■ Monitor/Squelch Y our dealer can program a key with the Monitor or Squelch function one of four ways: Squelch Momentary: Press and hold the Squelch key to hear background noise. Release the key to return to normal operation. Squelch Off: Momentarily press the Squelch key to hear background noise.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Kenwood TK-270G è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Kenwood TK-270G - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Kenwood TK-270G imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Kenwood TK-270G ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Kenwood TK-270G, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Kenwood TK-270G.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Kenwood TK-270G. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Kenwood TK-270G insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
