Manuale d’uso / di manutenzione del prodotto KCA-R42FM del fabbricante Kenwood
Vai alla pagina of 17
©PRINTED IN JAPAN B64-1930-00 (K/M) '01/12 11 10 9 8 7 6 5 4 3 2 1 '00/12 11 10 CONTROLLER FOR DISC AUTO CHANGER / FM MODULATOR SYSTEM INSTR UCTION MANU AL CONTROLEUR POUR CHANGEUR AUTOMATI.
— 2 — English Contents Before use Safety Precautions ........................................................................3 Buttons Display Unit ..................................................................................5 Remote Control .
— 3 — CD MD AUTO CHANGER CONTROLLER REP RDM 3 - + 4¢ PWR M.RDM D.REP TRACK DI SC 8 / D.SCN MHz DISC TRACK FREQ LEVEL Reset button Take the following precautions to prevent fire and avoid personal injury: • When extending the ignition wire, battery wire, or ground wire, use 0.
— 4 — English Safety Precautions Do not set the remote on hot places such as above the dashboard. Loading and Replacing the Batteries: Use two "AAA" batteries.
— 5 — CD MD AUTO CHANGER CONTROLLER REP RDM 3 - + 4¢ PWR M.RDM D.REP TRACK DI SC 8 / D.SCN MHz DISC TRACK FREQ LEVEL Playing CDs/MDs : Press the PWR button. The power goes ON and the CD/MD play start. When the unit receives any signal from the remote controller, the mark lights up.
— 6 — English Using the remote control, make direct input of the track number that you want to listen to. Using the number buttons on the remote control, enter the number of the track that you want to listen to. The selected track number blinks in the display for 10 seconds.
— 7 — Using the remote control, make direct input of the disc number that you want to listen to. Using the number buttons on the remote control, enter the number of the disc that you want to listen to. The selected disc number blinks in the display for 10 seconds.
— 8 — English Play the tracks on all the discs in the disc changer in random order. Press the M.RDM button to switch the magazine random play function on and off. The M.RDM indicator lights up when the magazine random play function is turned on. The display of the disc and track numbers change continuously as the next track is being selected.
— 9 — To set the frequency change mode Hold down the REP button for more than three seconds. The FREQ indicator will light up and the currently set frequency will be displayed. • The initial value is 88.3MHz. • If this function is on, the functions other than power on / off, reset, and modulation level / dynamic control, cannot be operated.
— 10 — English Dynamic control The unit comes with the prevention of distortion function to reduce sound distortion. If the sound is distorted severely, press the + button on the display unit and then set the function to "2" (ON). If the prevention of distortion function is set to "2" (ON), the sound extension is reduced.
— 11 — Accessories External view ......... Number of items .........1 2 .........2 1 The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above.
— 12 — English CD MD AUTO CHANGER CONTROLLER REP RDM 3 - + 4¢ PWR M.RDM D.REP TRACK DISC 8 / D.SCN MHz DISC TRACK FREQ LEVEL To prevent fire when the ignition wire (Red) or battery wire (Yellow) is short-circuited by coming into contact with the vehicle chassis (ground), only connect the power supply after making the fuse box connections.
— 13 — Installation Installation of Display unit ■ • Installation without using the trim mount plate 3 Attach one velcro to the slanted-line of the the display units as shown above, and attach the other velcro to the parts where you wish to attach the display units.
— 14 — English Troubleshooting guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. SOLUTION POSSIBLE CAUSE PROBLEM Power button is not turned ON.
— 15 — SOLUTION POSSIBLE CAUSE PROBLEM Nothing appears on the display. Sound distortion. The disc is dirty or damaged. If sound skips at the same part, the disc is faulty. Check and, if possible, clean the disc. The unit is mounted at a slant. Mount the unit so that is level.
— 16 — English Specifications subject to change without notice. Specifications Modulating Frequency (200KHz STEP) ............ 87.7, 87.9, 88.1, 88.3, 88.5, 88.7, 88.9, 89.1, 89.3, 89.5, 89.7, 89.9 , MHz General Operating Voltage .................
KCA-R42FM_U.S(K/En) 02.12.16 9:13 AM Page 17.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Kenwood KCA-R42FM è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Kenwood KCA-R42FM - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Kenwood KCA-R42FM imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Kenwood KCA-R42FM ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Kenwood KCA-R42FM, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Kenwood KCA-R42FM.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Kenwood KCA-R42FM. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Kenwood KCA-R42FM insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
