Manuale d’uso / di manutenzione del prodotto 625.3483400 del fabbricante Kenmore
Vai alla pagina of 36
PRINTED IN U.S.A. SA VE THIS MANUAL Use plastic bag and tie provided, to hang manuals nearby the softener for future reference. W ater Softeners ◆ W arranty ◆ Start Up / Setting T imer ◆ How It .
W ARRANTY 2 SEARS RESIDENTIAL W A TER SOFTENER FULL ONE YEAR W ARRANTY ON W A TER SOFTENER For one year from the date of purchase, when this water softener is installed and maintained in accordance with our instructions, Sears will repair , free of charge, defects in material or workmanship in this water softener .
T ABLE OF CONTENTS 3 P AGE NO. SECTION 1 SOFTENER ST ART UP A. SAFETY GUIDES 4 B. CHECK LIST OF STEP-BY -STEP GUIDES T O INST ALL 5 C. PROGRAM THE TIMER 6 D. SANITIZING THE W A TER SOFTENER 7 E. FILL THE STORAGE T ANK WITH SAL T 8 SECTION 2 HOW YOUR W A TER SOFTENER WORKS A.
W A TER SOFTENER ST ART -UP SECTION 1 4 1A. SAFETY GUIDES ▲ Read all steps, guides and rules carefully be- fore installing and using your new water softener . Follow all steps exactly to correctly install. Fail- ure to follow them could cause personal injury or property damage.
W A TER SOFTENER ST ART -UP SECTION 1 5 1B. CHECK LIST OF ALL STEP-BY -STEP GUIDES TO INST ALL Refer to the Installation Manual, part no. 7141417, for stepĆbyĆstep guides. T o be sure you have done all the steps to install the softener , r ead the following list.
W A TER SOFTENER ST ART -UP SECTION 1 6 1C. PROGRAM THE TIMER FIG. 1 ON / OFF V ACATION RECHARGE NOW Solid State Water Softener display buttons Standard Capacity HOLD PRESENT TIME AND DA Y RECHARGE TIME RECHARGE DA Y SET / CLEAR 1.
W A TER SOFTENER ST ART -UP SECTION 1 7 1D. SANITIZING THE W A TER SOFTENER Care is taken at the factory to keep your water softener clean and sanitary. Materials used to make the softener will not infect or contaminate your water supply, and will not cause bacteria to form or grow.
W A TER SOFTENER ST ART -UP SECTION 1 8 1E. FILL THE STORAGE T ANK WITH SAL T Brine (salt dissolved in water) is needed for each and every regeneration. The water for making brine is metered into the salt storage tank by the softener . However , you must keep the tank filled with salt.
HOW YOUR W A TER SOFTENER WORKS SECTION 2 9 2A. F ACE PLA TE TIMER FEA TURES RECHARGE NOW — If you have guests visiting, or other times when you use more water than usual, you could begin to run out of soft water . If the softener is not scheduled to regenerate for another day or 2, you would get hard water until then.
HOW YOUR W A TER SOFTENER WORKS SECTION 2 10 2A. F ACE PLA TE TIMER FEA TURES TIMER “POWER-OUT AGE MEMOR Y” — If electrical power to the timer goes of f, the memory" built into timer circuitry keeps all settings for 6 hours (minimum) or more.
HOW YOUR W A TER SOFTENER WORKS SECTION 2 11 2B. SOFT W A TER SERVICE AND REGENERA TION SERVICE When the softener is giving you soft water , it is called Service". During service, hard water comes from the house main water pipe into the softener .
HOW YOUR W A TER SOFTENER WORKS SECTION 2 12 2B. SOFT W A TER SERVICE AND REGENERA TION BRINING: During brining, the brine is moved from the salt storage area, into the resin tank. Inside the resin tank, brine cleans hardness minerals from the resin beads and they are discharged out the drain.
HOW YOUR W A TER SOFTENER WORKS SECTION 2 13 2B. SOFT W A TER SERVICE AND REGENERA TION AUTOMA TIC BYP ASS During the brining, brine rinse and backwash cycles of regeneration, HARD water goes through the softener valve and to the house pipes. If a faucet is opened, hard water is there for your needs.
CARE OF YOUR SOFTENER SECTION 3 14 3A. SAL T … REFILLING STORAGE T ANK/BREAKING A SAL T BRIDGE WHEN TO REFILL WITH SALT: Check the salt level a few weeks after you install the softener and every week after that. Refill when the storage tank is about 1/3 full.
CARE OF YOUR SOFTENER SECTION 3 15 3B. KEEPING THE W A TER SOFTENER CLEAN COVERS T o keep your new Sears water softener looking nice, apply a coat of paste wax and repeat once a year . When dusty, wipe it with a damp cloth to keep it sparkling. NOTE: Never use cleaners having ammonia or abrasives.
CARE OF YOUR SOFTENER SECTION 3 16 3C. KEEP THE SOFTENER FROM FREEZING If the softener is installed where it could freeze (summer cabin, lake home, etc.), you must drain all water from it to stop possible freeze damage. T o drain the softener Ċ 1. Close the shutĆoff valve on the house main water pipe, near the water meter or pressure tank.
CARE OF YOUR SOFTENER SECTION 3 17 3D. HELPFUL HINTS CHECKLIST ... TO HELP YOU SA VE MONEY NOTE: Read ERROR CODE", page 9. If your water softener fails to work, make the following easy checks. Often, you will find what's wrong yourself and you won't have to call and wait for service.
OTHER THINGS TO KNOW SECTION 4 18 4A. HOW TO “FINE-TUNE” YOUR SOFTENER It is not hard to fineĆtune your softener , but it does take a few minutes of your time to do it right. Y ou may save up to 500 pounds or more of salt each year with proper tuning.
OTHER THINGS TO KNOW SECTION 4 19 4A. HOW TO “FINE-TUNE” YOUR SOFTENER c . Press the RECHARGE DA Y button and SUnday begins to flash. –– If you regenerations on Sunday (from regeneration table), press the SET/CLEAR button to display ON .
OTHER THINGS TO KNOW SECTION 4 20 4A. HOW TO “FINE-TUNE” YOUR SOFTENER REGENERA TION T ABLE W A TER HARDNESS – GRAINS PER GALLON Up to 5 6 to 10 11 t o 15 16 to 20 21 to 25 26 to 30 31 to 35 36 .
OTHER THINGS TO KNOW SECTION 4 21 4B. DIMENSIONS/SPECIFICA TIONS FIG. 16 BYP ASS V AL VES INCHES CM A Salt T ank Height 40-1/4 102.2 B Resin T ank Diameter(nominal) 8 20.3 C Resin T ank Height (nominal) 40 101.6 D Inlet-Outlet Height 41-1/2 105.4 E Overall height 46 1 16.
SERVICER’S TECH. INFORMA TION SECTION 5 22 5A. ELECTRICAL CONNECTIONS IMPORT ANT : ! # $! # .
SERVICER’S TECH. INFORMA TION SECTION 5 23 5B. REGENERA TION CYCLE TIMES See regeneration table on page 20, and specifications, page 21. CYCLE FLOW RA TES (GALLONS PER MINUTE) FILL (flow to salt storage tank) 0.1 (1.1 liters) BRINING .16 (.6 liters) BRINE RINSE (flow to drain) .
SERVICER’S TECH. INFORMA TION SECTION 5 24 5C. TROUBLESHOOTING AUTOMA TIC ELECTRONIC DIAGNOSTICS The face plate has a selfĆdiagnostic function for the electrical system (except input power). The face plate monitors the electronic components and circuits for correct operation.
SERVICER’S TECH. INFORMA TION SECTION 5 25 5C. TROUBLESHOOTING a . If it move into fill, valve motor is inoperaĆ tive. Check all wiring and connections. b . If water enter tank, see QuickĆCheck T roubleshooting," page 26.
SERVICER’S TECH. INFORMA TION SECTION 5 26 5C. TROUBLESHOOTING *NOTE: Proper draw indicated.Be sure to check for a salt bridge. As a positive check for brine draw into the resin tank, keep softener in brining for 20 minutes or more. Then, make a taste test for salt at the drain water .
SERVICER’S TECH. INFORMA TION SECTION 5 27 5D. ROT AR Y V AL VE SERVICE Before working on the valve, turn of f the water supply and disconnect from electrical power . TO RELIEVE PRESSURE: -- 3 V AL VE BYP ASS: Close the inlet valve and open a soft water faucet.
SERVICER’S TECH. INFORMA TION SECTION 5 28 5E. W A TER FLOW THROUGH THE SOFTENER V AL VE SERVICE CYCLE .
SERVICER’S TECH. INFORMA TION SECTION 5 29 5E. W A TER FLOW THROUGH THE SOFTENER V AL VE BRINING AND BRINE RINSE CYCLES After fill, timer/switch action allows the motor to turn the rotor and disc into BRINING position. W ater flow is directed to the nozzle.
SERVICER’S TECH. INFORMA TION SECTION 5 30 5E. W A TER FLOW THROUGH THE SOFTENER V AL VE F AST RINSE CYCLE .
SERVICER’S TECH. INFORMA TION SECTION 5 31 NOTES.
REP AIR P ARTS SECTION 6 32 SEARS W A TER SOFTENERS MODEL NOS. 625.3483400 AND 625.3483500 KEY NO. P ART NUMBER DESCRIPTION 1 7137604 Cover (main) 2 7137612 Salt Hole Cover 3 71 18333 Wire Harness (switch) 4 7084330 Power Cord (transformer) 5 7144978 T imer Repl.
REP AIR P ARTS SECTION 6 33 28 29 SEARS W A TER SOFTENERS MODEL NOS. 625.3483400 AND 625.3483500 KEY NO. P ART NUMBER DESCRIPTION 30 0505957 Lead W asher 31 0513860 Float Stop 32 7092317 Float 33 0516.
REP AIR P ARTS SECTION 6 34 SEARS W A TER SOFTENERS MODEL NOS. 625.3483400 AND 625.3483500 49.
REP AIR P ARTS SECTION 6 35 SEARS W A TER SOFTENERS MODEL NOS. 625.3483400 AND 625.3483500 P ARTS LIST KEY NO. P ART NUMBER DESCRIPTION 50 7131755 Screw , #6-20 x 7/8 (2 req.) 51 7133008 Motor (incl. 2 ea. of Key No. 50) 52 0900857 Screw , #6-20 x 3/8 (2 req.
7147803 ( R. 7/95 ) W A TER SOFTENER The model number of your water softener is found on the rating decal. This decal is on the rim, under the salt hole cover . All repair parts are available for immediate pur- chase or special order when you visit your near- est Sears Service Center , or the Service Depart- ment at most Sears Stores.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Kenmore 625.3483400 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Kenmore 625.3483400 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Kenmore 625.3483400 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Kenmore 625.3483400 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Kenmore 625.3483400, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Kenmore 625.3483400.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Kenmore 625.3483400. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Kenmore 625.3483400 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
