Manuale d’uso / di manutenzione del prodotto 840116 del fabbricante Kawasaki
Vai alla pagina of 16
8" BENCH DRILL PRESS INSTRUCTION MANUAL FOR CUSTOMER SERVICE POUR LE SERVICE APRÉS VENTE OU DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1-800-590-3723 Printed in China 87-1904-60957 KAW ASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™ MOTORS CORP .
SECTION FOUR MAINTENANCE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-26 SPECIFICA TIONS . . . . . . . . . . . . . . . .
GENERAL SAFETY RULES – FOR ALL ELECTRIC POWER TOOLS RE AD AN D UND ER ST AND ALL INS TRUC TIO NS . Fa il ur e to fol lo w all ins tru ct io ns li st ed bel ow ma y re sult in ele ct ri c sh ock, fi re and /o r se rio us per so na l in jury . KEEP GUARDS IN PLACE AND IN WORKING ORDER.
This drill press is equipped with a grounded 3-wire power cord with a 3-prong plug. If the power cord will not fit into the wall plug, an approved adapter can be used as long as it is connected to the center screw in the wall plate. See Figure 1 and the steps below to use an AC grounding adapter: 1.
USE ONL Y DRILL BITS, SANDING DRUMS, AND OTHER ACCESSORIES that are designed for the various speeds of this drill press. The drill bits, sanding drums and other accessories should have a shank size 1/2" OR SMALLER. Unsuitable drill bits can break without warning throwing fragments outward at high speeds possibly causing severe injuries.
SECURE THE ELECTRICAL POWER CORD when the drill press is not in use to prevent unauthorized use of the tool and/or to prevent children from acciden- tally turning it on. ADDITIONAL INFORMA TION about the proper use of bench-mounted drill presses is available from the Power T ool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www .
FUNCTIONAL DESCRIPTION CONTROLS AND COMPONENTS: 1. Drill Bit 2. Column Assembly 3. Feed Handles 4. Chuck Key 5. Drill Chuck 5. Head Assembly 6. Knob (and mtg Hardware) 7. Work T able ASSEMBL Y Do not begin assembly of Bench-mounted Drill Press if the AC power cord is plugged into an AC power receptacle.
Ensure the spindle taper (Q) and the tapered hole in the drill chuck (R) are clean and free of any grease, lacquer , or rust preventative coatings. These compounds can cause the drill chuck (R ) to seize when installed on the spindle shaft (Q). INST ALLING THE DRILL CHUCK 1.
LASER GUIDE Use of controls or procedures, or performance of proce- dures other then those specified herein may result in hazardous radiation exposure. LASER SAFETY NEVER LOOK INTO THE LASER BEAM. Any contact with the eyes by the beam could cause injury .
17 18 STORE OUT OF REACH OF CHILDREN. Equipment should be in a high location or locked up to keep out of reach of children. It is not a toy . DO NOT T AMPER WITH THE LASER OUTPUT . Changing the performance of the laser to increase its output is prohibited.
Ensure that the switch toggle, when removed, is kept in a secure place. Once removed, the drill press will not start without it. ADJUSTING THE WORK T ABLE 1. The worktable (1) can be raised or low- ered on the drill press column (2) by loosening the table clamp (3).
1. Lift up the pulley cover (1). 2. Release the belt tension by loosen- ing the tension lock knob (2) located on the side of the drill press head. Loosen the tension lock knob (2) by turning it counterclockwise. 3. Pivot the motor (3) towards the front of the drill press.
3. T urn the spring housing (5) counter- clockwise to increase the spring ten- sion or clockwise to decrease the spring tension. 4. T urn nut (4 - inside) until it contacts the spring housing (5). Back nut (4) out 1/4 turn and tighten it against nut (3 - outside) to hold the spring housing in place.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets. I f t h e d r il l p r es s mu s t b e us e d o u ts id e , u s e a n ex t en si o n c o rd l a be l e d “ W - A ” o r “W .
Warranty Performance By pur chasing the product, purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replace.
ALL TRADE AND/OR ITS REPRESENT A TIVE(S), OR THE PURCHASER, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANT ABILITY AND THE W AR RA NTY OF FI TN ES S FOR A P AR TI CU LA R PUR POS E, AR E HER EB Y EXP RESS L Y EXCLUDED AND DISCLAIMED BY ALL TRADE AND/OR ITS REPRESENT A TIVES.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Kawasaki 840116 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Kawasaki 840116 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Kawasaki 840116 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Kawasaki 840116 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Kawasaki 840116, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Kawasaki 840116.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Kawasaki 840116. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Kawasaki 840116 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
