Manuale d’uso / di manutenzione del prodotto DC-1100G del fabbricante Jet Tools
Vai alla pagina of 20
Operating Instructions and Parts Manual Dust Collector Model: DC-1100A/C/RC DC-1100A/RC DC-1100C/RC WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No.
2 This manual has been prepared fo r the owner and operators of JET DC-11 00 Series Dust Collectors. Its purpose, aside from machine operatio n, is to prom ote safety using accepted operatin g and maintenance procedures.
3 Table of Contents Warranty and Service ........................................................................................................... ................................ 2 Table of Contents .................................................
4 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Read and un derstand the warnings posted on the machi ne and in this manual. Failure to co mply with all of these warnings may cause serious inju ry.
5 blahblahblah 20. Make your workshop child proof with padlocks , master switc hes or by removing starter keys. 21. Give your work undivided attention. Loo king arou nd, carrying on a conversation a nd “horse-play” are careless acts that can result in seriou s injury.
6 Introduction This manual is provided by JET covering the safe operation and maintenan ce procedures for model DC-1100 Series Dust Collectors. This manual contains instructions on inst allation, safety precaution s, general operating procedures, maintenance in structions and par ts breakdown.
7 Unpacking DC-1100A/RC Dust Collector 1. Remove all contents fr om the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembl ed and is running properly.
8 Unpacking DC-1100C/RC Dust Collector 1. Remove all contents fr om the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembl ed and is running properly.
9 Assembly Base 1. Install four casters to the under side of t he base as pictured in Fig. 2. 2. Thread the hex nut (B, Fig. 1) onto the caster shaft. Then slide the lock washer (A, Fig. 1) over the caster shaft. Thread the caster shaft into the threaded hole on the undersi de of the base, turn until snug.
10 Connector Housing 5. Attach three support brac kets (A, Fig. 4) to the base using six M8 x 16 hex cap bolts and six M8 flat washers (B, Fig. 4). Hand-tighten only at this time. 6. Install the housing (A, Fig. 5) to two support brackets (B, Fig. 5) using four M8 x 16 hex cap bolts, eight M8 flat washers, and four M8 hex nuts (C, Fig.
11 Filter Bag Installation – DC-1100A/RC Referring to Figure 7: 1. Place the hanger (A) on the hanger bracket (B). 2. Slide the filter bag loop (C) over the hanger hook. 3. Thread the re tainer strap (D) through the loops on the filter bag (E) and fasten to the collector housing (F).
12 Collector Bag Installation – DC-1100C/RC 1. Place the rin g over the top of the plastic bag an d fold over the bag approximately three inche s, Figure 9. 2. Insert the snap ring (A, Fig. 10) of the collector bag into the bottom of the housing at an angle.
13 Electrical Connections All electrical connections must be done by a qualified electrician. All adjustments or repairs must be done with the dust collector disco nnected from the power source, unplugged. Failu re to comply may result in serious injury! The DC-1100A/RC and DC-110 0C/RC dust collectors are rated at 115/230V, Prewired 115V .
14 Maintenance Never perform maintenance on this machine before turning s witch off and removing plug from power source. Failure to comply may cause serious injury! Cleaning the Filter Bag – DC-1100A/RC Wearing a particle mask or respirator for protection against fine dust particles during cleaning is highly recommended.
15 Parts List – DC -1100A/RC Dust Collector Index No. Part No. Description Size Qty 1 ............... 411035W ................. Impe ller Hous ing ....................................................................... ..............................
16 Parts Breakdown – DC -1100A/RC Dust Collector.
17 Filter Assembly for DC-1100C/RC Models Index No. Part No. Description Size Qty 1 ............... 331050..................... Handle ....................................................................................................................
18 Remote Control Breakdown for DC-1100RC Index No. Part No. Description Size Qty ................. DC1100RC-100 ....... Receiver Assembly (Ite ms 1-12) ............................................................. ............... 1 1 ............... DCRC-101 .
19 Wiring Diagram – DC-1100A/C.
20 Wiring Diagram – DC-1100RC.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Jet Tools DC-1100G è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Jet Tools DC-1100G - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Jet Tools DC-1100G imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Jet Tools DC-1100G ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Jet Tools DC-1100G, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Jet Tools DC-1100G.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Jet Tools DC-1100G. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Jet Tools DC-1100G insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
