Manuale d’uso / di manutenzione del prodotto CONTROL NOW AW del fabbricante JBL
Vai alla pagina of 29
JBL CONTROL NOW ™ JBL CONTROL NOW ™ AW JBL ® CONTROL ® SERIES OWNER’S GUIDE ® JBLP2605_CN_CNAW_PM-OM 4/23/08 12:57 PM Page 1.
2 T ABLE OF CONTENTS UNP ACKING THE SPEAKERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 W ALL SURFACE-MOUNTING . . . . . . . . . . . .
3 PLACEMENT JBL Control NOW speakers are perhaps the most flexible and versatile loud- speakers ever developed. There are numerous mounting options. The JBL Control NOW speaker can be wall-mounted or corner -mounted, sit on a shelf or be used with floor stands.
4 W ALL SURF ACE-MOUNTING When deciding upon a location for the JBL Control NOW speaker , take care NOT to install the mounting bracket closer than 3" (horizontal) and 8-1/2" (vertical) to the ceiling.
5 4. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting-bracket cap with two screws through the bottom of the mounting bracket. Rest the JBL Control NOW speaker’ s rear flange in the mounting bracket, as shown.
6 W ALL CORNER-MOUNTING CA UTION The customer is responsible for proper selection and use of mounting hardware (available through hardware stores), to properly and safely wall-mount the speakers. The JBL Control NOW speaker was designed to be easily installed.
7 4. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting-bracket cap with two screws through the bottom of the mounting bracket. Rest the JBL Control NOW speaker’ s rear flange in the mounting bracket, as shown.
8 3. Connect the wires to the JBL Control NOW speaker . IMPORT ANT : Make sure all equipment is turned off before making any connections. For speaker connections, use a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i.
9 4. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting-bracket cap with two screws through the side of the mounting bracket. Rest the JBL Control NOW speaker’ s flange in the mounting bracket, as shown.
10 HALF-ROUND W ALL-MOUNTING (HORIZONT AL OR VERTICAL) NOTE: Decide whether you will connect the speakers as a single channel or two separate channels, and follow the appropriate instructions on the following pages.
11 5. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting-bracket cap with two screws through the bottom of the mounting bracket.
12 CONNECT AS TWO CHANNELS CA UTION The customer is responsible for proper selection and use of mounting hardware (available through hardware stores), to properly and safely wall-mount the speakers. The JBL Control NOW speaker was designed to be easily installed.
13 4. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting bracket cap with two screws through the bottom of the mounting bracket. This will support the weight of the speaker . Now slide the mounting-bracket cap over the assembly .
3/4-ROUND W ALL-MOUNTING CA UTION The customer is responsible for proper selection and use of mounting hardware (available through hardware stores), to properly and safely wall-mount the speakers. The JBL Control NOW speaker was designed to be easily installed.
15 4. Connect the small end of the multiunit wiring adapter to the rear of speaker 1, as shown. 5. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting-bracket cap with two screws through the bottom of the mounting bracket.
16 9. Place the large end of the multiunit wiring adapter that is already installed in speaker 2 into speaker 3 by sliding a multiunit wiring adapter into the rear of it at a slight angle and rotate clockwise. 10. Connect the terminal assembly to the back of the second multiunit wiring adapter .
17 ST AND-MOUNTING IMPORT ANT SAFETY NOTE: CA UTION The supplied floor stand adapters facilitate installation with a variety of general- purpose floor stands available from many manufacturers.
CA UTION The JBL Control NOW PMB Pole-Mount Bracket facilitates installation of the JBL Control NOW and JBL Control NOW A W loudspeakers with a variety of general-purpose ceiling-fan-pole assemblies available from many manufacturers.
19 2A. Slide the pole-mount bracket up onto the drop tube, aligning the pinholes on the bracket with those on the drop tube. (FOR SMALLER-DIAMETER DROP TUBES) 2B. When using a smaller drop tube, use the pole bushing when running the wiring down through pole-mount-bracket cap.
SPEAKER WIRING 1. Use the cable assembly provided to wire the units for a single channel. Single-channel-wiring diagram. 2. Use the multiunit wiring adapters to wire the units for two channels. NOTE: There are two options for 2-channel wiring: 2A. Even sound distribution – Use this connection for even sound distribution through both channels.
21 SINGLE-CHANNEL WIRING 1. Use the cable assembly provided. Run the cable assembly down the drop tube; run the four sets of paired wires out through the wire access holes, as shown. NOTE: This procedure is applicable for both large- and small-diameter drop tubes.
2-CHANNEL WIRING FOR EVEN SOUND DISTRIBUTION 1. Use the even sound distribution connection for even sound distribution through both channels. Run the sets of paired wires out two wire access holes through the pole-mount bracket, as shown. NOTE: This procedure is applicable for both large- and small-diameter drop tubes.
23 7. Connect the wires to the terminal assembly and place the speaker on the pole-mount bracket. Repeat this process with speaker D. Return to the installation procedures and continue. IMPORT ANT : Make sure all equipment is turned off before making any connections.
2-CHANNEL STEREO WIRING 1. Use the stereo sound-distribution connection for a smaller home theater/stereo environment. Run the sets of paired wires out two opposite wire access holes through the pole-mount bracket, as shown. NOTE: This procedure is applicable for both large- and small-diameter drop tubes.
25 7. Connect the wires to the terminal assembly and place the speaker on the pole-mount bracket. Repeat this process with speaker A. Return to the installation procedures and continue. IMPORT ANT : Make sure all equipment is turned off before making any connections.
26 #10-32 x 2" Screws (4) Drop Tube Pole- Mount-Bracket Cap Pole- Mount Bracket Onl y t wo speakers shown here for clarity. Place the pole-mount-bracket cover over the bottom visible mounting bracket by snapping it into place.
27 MAINTENANCE AND SERVICE The enclosure may be cleaned using a soft cloth to remove fingerprints or to wipe off dust. All wiring connections should be inspected and cleaned or remade periodically .
28 JBL CONTROL NOW ™ JBL CONTROL NOW ™ AW Frequency Response (–6dB) 80Hz – 30kHz Max. Recommended Amplifier Power* 150W Power Handling (Continuous/Peak) 50W/300W Sensitivity (2.
Features, specifications and appearance are subject to change without notice. JBL and Bi-Radial are trademarks of Harman International Industries, Incorporated, registered in the United States and/or other countries. JBL Control NOW , PolyPlas and Pro Sound Comes Home are trademarks of Harman International Industries, Incorporated.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il JBL CONTROL NOW AW è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del JBL CONTROL NOW AW - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso JBL CONTROL NOW AW imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul JBL CONTROL NOW AW ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il JBL CONTROL NOW AW, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del JBL CONTROL NOW AW.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il JBL CONTROL NOW AW. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo JBL CONTROL NOW AW insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
