Manuale d’uso / di manutenzione del prodotto CV-M300 del fabbricante JAI
Vai alla pagina of 24
Opera tion Manual Industrial Monochrome CCD Camera (Rev.E) CV -M300.
CV -M300 DECL ARA TION OF CONFORMIT Y AS D EFINE D B Y THE C O UN CI L D IREC T I VE 89/336/EEC E MC (E LECTR OMAG N E TIC C OMP A TI B ILITY ) WE HE R E WITH DECLAR E THA T TH IS PRODUCT C OM PLI E S WITH THE FOLL OWI NG PR OVISIONS APPL YI NG T O IT .
- 2 - CV -M300 T able of Contents T able of Contents .............................................................................................................. ......................... 2 1 . General ...............................................
- 3 - CV -M300 1. General The CV -M300 is a monochrome 2/3" CCD camer a designed for automated imaging applications featuring high performance and unique functions within a uniform and compact housing.
- 4 - CV -M300 4. Locations and F unctions 1 2/3" interline transfer CCD sensor. 2 Lens mount of C-mount type. *1) 3 BNC connector for video output. 4 Switch block SW1 for shutter speed and function modes setting. 5 6-pin multi connector for WEN and EEN output external trigger input.
- 5 - CV -M300 5. Pin Assignment 5.1. 12-pin Multi-connector (DC-IN/SYNC.) T ype: HR10A-10R-12PB-01 (Hirose) male Seen from rear. Notes: *1 ) Signals on pin no. 6, 7 and 9 can be changed by jumper setting. See “7.3. Jumper Settings” for more information.
- 6 - CV -M300 6. F unctions and Operations 6.1. Input/Output of HD/VD Signal 6.1.1. Input of External HD/VD Signal As factory setting the camera can be synchronized by external HD/VD signals. The signal level must be 4.0 Vp-p ± 2.0V at the input with the 75 Ohm termination ON.
- 7 - CV -M300 T o use this mode Set: SW1-4 to ON for ext. trigger shutter SW1-5 to OFF for field accumulation SW1-6 to ON for non-interlaced SW1-1, 2 and 3 to shutter speed Input: Ext. trigger to pin 5 on 6 pin multi connector. Ext. HD to pin 6 on 12-pin multi connector.
- 8 - CV -M300 CCIR (Non-interlaced / Field accumulation mode) 6.3.2. Pulse Width Control Mode The pulse width control mode will only work in non-interlaced field accumulation mode. The exposure is controlled by the lo w period of the ext. trigger pulse.
- 9 - CV -M300 Cautions in the Pulse Width Control Mode. 1. Pulse width control mode is effective only in non-interlaced field accumulation mode. 2. The exposure start may be delayed up to 1H max., when the falling edge of ext. trigger pulse is not synchronized with the falling edge of ext.
- 10 - CV -M300 6.3.3. Star t/Stop T rigger Mode The Start /Stop trigger will work in 3 modes: 1. Interlaced with frame accumulation. 2. Interlaced with field accumulation. 3. Non-interlaced with field accumulation. The exposure time is controlled by the interval between the ext.
- 11 - CV -M300 Cautions in the Star t/Stop T rigger Mode. 1. The input of ext. VD signal must be given continuously to synchronize with int. VD signal. It is not possible to input ext. VD signal randomly. 2. The exposure start may delay up to 1H max.
- 12 - CV -M300 6.3.4. Long Time Exposure Mode The Long time exposure will work in 3 modes: 1. Interlaced with field accumulation. 2. Interlaced with frame accumulation. 3. Non-interlaced with field accumulation. The exposure time is the interval between 2 ext.
- 13 - CV -M300 Cautions in the Long Time Exposure Mode. 1. Theoretical exposure time is as follows. EIA: 1/30 sec. to ∞ . CCIR: 1/25 sec. to ∞ . 2. It is recommended not to use exposure > 2 sec. since visible dark-current noise may occur. 3. Ext.
- 14 - CV -M300 7. Mode Setting Cautions on Mode Setting. Before making any mode or jumper setting turn the po wer OF F . 7.1.1. SW1 Switch on the Rear Panel Factory settings for SW1 are with all 8 switches in OFF position. The shutter values are given for a CCIR camera having the factory settings.
- 15 - CV -M300 Cautions on Shutter . The image can flicker when the illumination is AC powered. Highlighted parts of the image will show increasing smear at a shorter shutter time. 7.1.4. Ext. T rigger Shutter Mode When trigger select SW1-4 is ON. The camera is in ext.
- 16 - CV -M300 7.3. Jumper Settings Cautions on Jumper Setting. Before making any mode or jumper setting turn the po wer OF F . Jumpers for mode setting are found on the boards PK8041 & PK8042. The following modes are available with jumper setting: Input/Output Mode of HD/VD signal.
- 17 - CV -M300 7.4. Location of SW2 and Jumpers Jumpers are shorted with a 0 Ohm resistor or b y a soldering between the 2 points. T o remove the solder tin from a jumper position, use a special tin remover such as de-soldering wick. 7.4.1. Board PK8041 Side A 7.
- 18 - CV -M300 8. Adjustment of Video Signal Output Level When an alignment of a video output signal is required, remove the camera housing and adjust potentiometers VR3, VR4 and VR5 on the PK8042 board while measuring their levels at the video output connector.
- 19 - CV -M300 9. External Appearance Unit : mm (inches) T ripod mount plate.
- 20 - CV -M300 10. Specifications Scanning system CCIR 625 lines EIA 525 lines 25 frames/sec. 30 frames/sec. CCD sensor Monochrome 2/3" IT CCD Sensing area 8.8 mm (h) x 6.6 mm (v) Effective pixels 752 (h) x 582 (v) 768 (h) x 494 (v) Elements in video output 737 (h) x 575 (v) 758 (h) x 486 (v) Cell size 11.
- 21 - CV -M300 11. Appendix 11.1. Precautions Personnel not trained in dealing with similar electronic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. The handling of these devices should follow the requirements of electrostatic sensitive components.
- 22 - CV -M300 12. User’s R ecord Camera type: CV -M300 Scanning system: EIA/CCIR Revision: (Revision E) Serial No. ................. Users Mode Settings Users Modifications This manual can be downloaded from: www.
JAI America, Inc., USA Suite 450 23046 Avenida de la Carlota Laguna Hills, CA 92653 USA Phone +1 949 472 5900 Fax +1 949 472 5908 www.jai.com JAI Corporation, Japan German Industry Center 1-18-2 Hakusan, Midori-ku Y okohama, Kanagawa 226-0006, Japan Phone +81 45 933 5400 Fax +81 45 931 6142 www.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il JAI CV-M300 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del JAI CV-M300 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso JAI CV-M300 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul JAI CV-M300 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il JAI CV-M300, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del JAI CV-M300.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il JAI CV-M300. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo JAI CV-M300 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
