Manuale d’uso / di manutenzione del prodotto CV-A1 del fabbricante JAI
Vai alla pagina of 24
Compact Monochrome Megapixel Progressive Scan Camera CV -A1 Operation Manual Camera: Revision B Manual: V ersion 1.2 A1manB12oct08.doc JPT 08 -10-03.
CV-A1 Table of Contents 1. General......................................................................................................... 2 2. Standard Compositi on ....................................................................................
CV-A1 1. Gener al The CV-A1 is a monochrome progressive scan 1/ 2” CCD c amera with 1.4 Megapixel resolution . It is designed for automated inspection, featuring a small hou sing and a wide range of unique functions.
CV-A1 4. Locations and F unctions Fig. 1. Locations. 1. 12 pin Hirose connector for frame grabber interfacing and power (12V DC). 2. BNC connector for video output. VS 1.0 Vpp 75 Ohm. 3. 6 pin Hirose connector for trigger input and RS-232C control interface.
CV-A1 5. Pin Assignment 5.1. 12-pin Multi-connector (DC- IN/VIDEO OUT, EXT.HD/VD IN) Type: HR10A-10R-12PB-01 (Hirose) male Seen from re ar P in configuration is compat ible with EIAJ standard Fig. 2. 12-pin connector. Plugs for cable: HR10A-10P-12S 5.
CV-A1 5.3. Input and Output Circuits In the following schematic diagrams the input and outpu t circuits for video and timing sig nals are shown. For alternat ive connections refer to “7.4. Intern al Switch and Jumper Se ttings.” Jumper settings are shown as for factory defaul t.
CV-A1 5.4. CV-A1 Block Diagram Fig. 8. Block diagram. 6. F unctions and Oper ations 6.1. Basic functions Some of the primary camera functions need a general introduction before the ope ration modes are described. The list below sh ows the primary functions fr om the command list.
CV-A1 Binning mode BI is a fun ction where the signal charge from 2 or m ore adjacent pixels are adde d together and read out as one pixel. A resulting full frame with lower resolution can be read out with a higher rate. By adding 2 pixels together, the sensitivity is doubled.
CV-A1 6.2. Input-output of HD/VD Signals In the default setting the camera will accept external HD/VD signals on pin 6 and 7 of the 12 pin Hirose connector. If external HD/VD is applied, th e camera will synchronize to it. If no external sync signals are applied, the camera will oper ate with its in ternal x-tal controlled sync.
CV-A1 6.3. Continuous Operation (Non triggered) Trigger Mode Normal. TR=0. It is for applications where the camera is continuous ru nning without external trigger.
CV-A1 6.4. External Trigger Modes This camera has 6 external asynchr onous trigger modes, wh ich can be set by RS-232C comman ds. 1. Edge Pre-select Mode.TR=1 Pre-selected exposure. (SM=0, SM=1) 2. Pulse Width Control Mode. TR=2 Pulse width controlled exposure.
CV-A1 6.5. Edge Pre-select Mode The exposure starts at the first HD pulse after t he trigger leading edge. It stops and is read out after the duration of the shutter time selected. It can be t he first 9 step in normal or 10 23 steps in programmable shutter.
CV-A1 6.6. Pulse Width Control Mode In this mode the exposure starts from the leading edge of the trigger pulse. It stops at the trailing edge of the trigger pulse, and the resul ting video is read out. The accumul ation can be either H synchronous or H asynchronous.
CV-A1 6.7. Frame-delay read out Mode In this mode the exposure starts from the leading edge of the trigger pulse. It stops at the trailing edge of the trigger pulse.
CV-A1 6.8. Long Time Exposure Mode The exposure time is the interval between 2 ex ternal VD pulses sent to the VD inp ut. The exposure starts after the input of a VD, and it ends after the next VD input, which again starts a new exposure. The interval between the external VD pulses (exposure time) can be from V to ∞ .
CV-A1 6.9. Start/Stop Mode The exposure is controlled by the interval between the external trigge r pulse and an external VD pulse. The exposure start at the first HD pulse af ter the trigger leading edge, and it stops after the rising edge of the VD.
CV-A1 6.10. Smearless Mode This mode will reduce the unwant ed smear signal from a highlighted scene when a short exposure time is used. The trigger mode is like edge pre-se lect, but a dummy readout is performed before the active accumulation is started.
CV-A1 6.11. Other Functions. Gain and analogue settings. !! Do not adjust these s ettings unless you have knowl edge to video adju stments !! The video gain can be set to AGC or manual . In AGC mode the video level is kept constant by the automatic gain control circuit within a 1 2 dB range.
CV-A1 7.2. CV-A1 RS-232C command list. Command Name Format Parameter Remarks A – General settings and useful co mmands EB Echo Back EB= [ Param. ] <CR><LF> 0=Echo off 1=Echo on Off at po.
CV-A1 7.3. Camera Control Tool for CV-A1 From www.jai.com CV-A1 Camera Control Tool for Windows 98/NT/200 0 can be downloaded. The control tool contents a camera control program and too ls for making your own program. Below the different windows are sh own.
CV-A1 7.4. Internal Switch and Jumper Settings For VD and HD input/ou tput and termination refer to “6.2. I nput-output of HD/VD Signals.” For alternative connections of pin #10 and #11 on 12-pin connector, ju mper JP1, JP2, JP3, JP4 and JP5 can be used.
CV-A1 9. Specifications Specifications CV-A1 Scanning system Progressive 1068 lines 16.037 frames/sec. Pixel clock 28.63636 MHz Line frequency 17.127 kHz (1672 pixel clock/line) Frame rate for full frame 16.037 frames/sec. (1068 lines/frame) CCD sensor 1/2” progressive monochrome IT CCD.
CV-A1 10. Appendix 10.1. Precautions Personnel not trained in dealing with similar elec tronic devices should not service this camera. The camera contains components sensitive to el ectrostatic discharge. The handling of these devices should follow the requirements of electrostatic se nsitive components.
CV-A1 11. Users Record Camera type: CV-A1 Revision: (Revision B) Serial No. …………….. Users Mode Settings Users Modifications DECLARA TION OF CONFORMITY AS DEFINED BY THE COUNCIL DIRECTIVE 89/336/EE C EMC (ELECTROMAGNETIC COMPAB ILITY) WE HEREWITH DECLARE THAT THIS PRODUCT COMPLIES WITH THE FOLOWING PROV ISIONS APPLYING TO IT.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il JAI CV-A1 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del JAI CV-A1 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso JAI CV-A1 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul JAI CV-A1 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il JAI CV-A1, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del JAI CV-A1.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il JAI CV-A1. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo JAI CV-A1 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
