Manuale d’uso / di manutenzione del prodotto LE-370/LE-370Z del fabbricante Intel
Vai alla pagina of 45
LE-370/LE-370Z 3.5 Inc hes Embedded Miniboar d User ’ s Manual Edition: 1.0 2005/6/13.
LE-370 User ’ s Manual Copyright Copyright 2004 - 2005. All rights reserved. This docume nt is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains propri etary information and protected by copyright.
LE-370 User ’ s Manual Packing List: Please check the packa ge before you starting setup the syste m Hardware: LE-370/LE-370Z motherboard x 1 Cable Kit: 44-pin 40-pin 44-pin 44-pin A T A33 IDE Cable.
LE-370 User ’ s Manual 4 Inde x Chapter 1 <Introduction > .................................................................................. 7 1.1 <Product Overview> .......................................................................
LE-370 User ’ s Manual 2.13 <Switch & Indicator> ......................................................................... 31 Chapter 3 <Sy stem Setup> ............................................................................. 33 3.
LE-370 User ’ s Manual 6 (This Page is Lef t For Blank).
LE-370 User ’ s Manual Introduction Chapter 1 <Introduction> 1.1 <Product Overview> LE-370/LE-370Z are the 3.5 inches embedded mini b oards based on Intel 852GME/GM of platform, with Intel Pentium M/Celeron M processors supported, onboard VGA, LAN, Audio, USB2.
LE-370 User ’ s Manual Introduction 1.2 <Product Specification> General Specification LE-370 LE-370Z Form Factor 3.5 inches Embedded Miniboard CPU Intel Pentium M/Celeron M Package: FC-PGA478 .
LE-370 User ’ s Manual Introduction Ethernet Interface Controller Intel 82562ET PHY Type 10Base-T / 100Base-TX auto-switching Fast Ethernet Full duplex, IEEE802.
LE-370 User ’ s Manual Introduction 1.3 <Mechanical Drawing> Mechanical Drawing 10.
LE-370 User ’ s Manual Introduction 1.4 <Block Diagram> Intel Pentium M processor with FC-P GA2/FC-BGA2 1 x 184-pin DDR DIMM up to 1GB CRT/LCD Monitor LV D S 852GME/GM 2 x USB2.
LE-370 User ’ s Manual 12 (This Page is Lef t for Blank).
LE-370 User ’ s Manual Ha rdware Setup Chapter 2 <Hardware Setup> 2.1 <Connector Location> CN_COM2 AUDIO C O M 1 CDIN C R T CN_INV RJ45 PS2 DC_IN CN_IR IDE1 J F R N T FDD CN_USB CN_AUDIO.
LE-370 User ’ s Manual Ha rdware Setup 2.2 <Jumper Location & Reference> Jumper Function JRTC CMOS Operating/Clear Setting JVLCD LCD panel voltage setting JVLCD JRTC Jumper Locat ion &.
LE-370 User ’ s Manual Ha rdware Setup 2.3 <Connector Reference> 2.3.1 <Internal Connector> Connector Function Remark DIMM 184-pin DDR SDRAM DIMM S tandard IDE1 44-pin primary IDE connec.
LE-370 User ’ s Manual Ha rdware Setup 2.4 <CPU & Memory Setup> 2.4.1 <CPU> LE-370 supports onboard socket47 9 for Intel Pentium M/Celeron M processors with FC-PGA478 package, 400/533MHz of front side bus; LE-370Z integrates onboar d Intel Celeron M 600MHz processor with 400MHz of front side bus.
LE-370 User ’ s Manual Ha rdware Setup 2.4.2 <Memory> LE-370 supports DDR2 66/333 up to 1GB with ECC; LE-370Z supports DDR200/26 6 up to 1GB with unbuffered, non-ECC memory module. DIMM 104-pin 80-pin Please check the pin nu mber to match the socket side w ell before installing memory module.
LE-370 User ’ s Manual Ha rdware Setup CPU & Memory Setup 18 2.4.3 <CPU Cooler Installation> The LE-370 provides one C PU cooler; please follow the instruction belo w to finish the installation. The LE-370Z comes with a heat sink on embedded processor , no fan is required.
LE-370 User ’ s Manual Ha rdware Setup 2.5 <CMOS Setup> The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS setting s, here is how to proceed to clear (reset) the CMOS to it s default values.
LE-370 User ’ s Manual Ha rdware Setup 2.6 <Enhanced IDE & CF interface> The board supports one UltraDMA1 33 IDE interface, and one CompactFlash T ype 1 socket with secondary IDE m ode, the 44-pin IDE1 connector can sup port up to 2 A T API devices through IDE cable.
LE-370 User ’ s Manual Ha rdware Setup 2.7 <Floppy Port> The board provides a slim t ype floppy port; please use the 26-pin ribbon cable in the package to connect the floppy device. FDD 1. Lift up the brown plastic bar 2. Slot the cable in (Blue paste for brown bar side) 3.
LE-370 User ’ s Manual Ha rdware Setup 2.8 <Ethernet Interface> The board integrates Ethernet controller with Intel 82562E T PHY , full compliance with IEEE 802.3u 100Base-T specificatio ns and I EEE 802.3x Full Duplex Flow Control, the board supports Wake-Up-On- LAN b y BIOS configurab le.
LE-370 User ’ s Manual Ha rdware Setup 2.9 <Onboard Display Interface> Based on Intel 852GME/GM chipset with built-in Intel Extreme Graphics, the board provides onboard VGA display interface, and one 18/24-bit L VDS LCD interface, supports up to 1600 x 1200 of resol ution for LE-370 (with 8 52GME) and 1400 x 1050 for LE-370Z (with 852GM).
LE-370 User ’ s Manual Ha rdware Setup 2.9.2 <Digit al Display Interface> The onboard digital display interface comes with a 40-p in header connector to provide 18/24-bit L VDS LCD interface, and one backlig ht invert er connector for powering and enable/disable control, the ju mper JVLCD is to set the panel voltage.
LE-370 User ’ s Manual Ha rdware Setup Connector: CN_INV C o n n e c t o r : JVLCD Type: 5-pin LVDS Power Header Type: 3-pin Power select Header Pin Description Pin Description 1 +12V 1 VCC 2 GND 2 LCDVCC 3 GND 3 VCC3 4 GND 5 ENABKL Connector: CN_LVDS Type: onboard 40-pin connect or for LVDS connector Connector model: HIROSE DF13-40DP-1.
LE-370 User ’ s Manual Ha rdware Setup To setup the LCD, you need the comp onent below: 1. A panel with LVDS interfaces. 2. An inverter for panel’s backlight po wer.
LE-370 User ’ s Manual Ha rdware Setup After setup the devices well, you need to select the LCD panel type in the BIOS. The panel type mapping is list belo w: BIOS panel type se lection form For 18-bit color For 24 -bit color NO.
LE-370 User ’ s Manual Ha rdware Setup 2.10 <Onboard Audio Interface> The board integrates o nboard AC97 au dio with REAL TEK ALC201A, supports 18-bit ADC and DAC resolution, and Line -out, Line-in and MIC-in input/output interfaces. Connector: CN_AUDIO Type: 10-pin (2 x 5) 1.
LE-370 User ’ s Manual Ha rdware Setup 2.11 <GPIO Interface> The board offers 8-bit digital I/O to customize its configuration to y our control needs. For example, you may configure t he digit al I/O to control the o pening and closing of the cas h drawer or to sense the warning signal from a tripped UPS.
LE-370 User ’ s Manual Ha rdware Setup 2.12 <Power Supply & Fan> 2.12.1 <Power Input> The board requires DC 12V input with onboard DC jack or 4-pin 12V DC connector. Connector: CN_12V Type: 4-pin standard AT X2.0 +12V power connector Pin Description Pin Description 1 Ground 2 Ground 3 +12V 4 +12V 2.
LE-370 User ’ s Manual Ha rdware Setup 2.13 <Switch & Indicator> The JFRNT provides front control p anel of the board, such as p ower button, reset and beeper , etc. Please check well before you connecting the cables on the chassis. Connector: JFRNT Type: onboard 14-pin (2 x 7) 2 .
LE-370 User ’ s Manual 32 (This Page is Lef t for Blank).
LE-370 User ’ s Manual S ystem Setup Chapter 3 <System Setup> 3.1 <Display Configuration> The board provides onb oard V GA with DB15 analog displa y interface, and L VDS LCD interface for digital display , when connecting t wo display devices, you can enable dual display function with clone mode or e xtended desktop mode.
LE-370 User ’ s Manual S ystem Setup Please select Devices for advance d device setting. Single Display Device Setting Dual Display Device Setting When you set dual disp la y clone mode, you’ll see the sam e screen d isplay on two devices.
LE-370 User ’ s Manual BIOS Setup Chapter 4 <BIOS Setup> The single boa rd computer uses the Award BIOS for the system configur ation. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers.
LE-370 User ’ s Manual 36 (This Page is Lef t for Blank).
LE-370 User ’ s Manual I/O Port Pin Assignment Appendix A <I/O Port Pin Assignment> A.1 <IDE Port> 2 44 Connector: IDE1 Type: 44-pin (22 x 2) box header 1 43 Pin Description Pin Descript.
LE-370 User ’ s Manual I/O Port Pin Assignment A.2 <Floppy Port> Connector: FDD Type: 26-pin connector Pin Description Pin Description 1 VCC 2 INDEX 3 VCC 4 DRV0 5 VCC 6 DSKCHG 7 DRV1 8 N/C 9 .
LE-370 User ’ s Manual I/O Port Pin Assignment A.5 <Serial Port> 1 2 3 4 5 6 7 8 9 Connector: COM1 Type: 9-pin D-sub male conn ector on brack et Pin Description Pin Description 1 DCD 6 DSR 2 RXD 7 RTS 3 TXD 8 CTS 4 DTR 9 -XR 5 Ground 12 C o n n e c t o r : CN_COM2 10 9 Type: 10-pin (2 x 5) 1.
LE-370 User ’ s Manual I/O Port Pin Assignment A.8 < LPT Port > 14 26 Connector: CN_LPT 1 13 Type: 26-pin (13 x 2) header for LPT Ports Pin Description Pin Description 1 PSTB- 2 PRO0 3 PRO1 4 .
LE-370 User ’ s Manual I/O Port Pin Assignment (This Page is Lef t for Blank) Serial Port 41.
LE-370 User ’ s Manual Flash BIOS 42 Appendix B <Flash BIOS> B.1 BIOS Auto Flash T ool The board is based on A ward BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool onlin e at the addr ess below: http://www.
LE-370 User ’ s Manual Flash BIOS (This Page is Lef t for Blank) Flash BIOS 43.
LE-370 User ’ s Manual H ardware T est Appendix C <Hardware Test> C.1 <Power Consumption Test> Hardware Board LE-370Z CPU Intel® Celer on® M 600MHz Memory Infineo n DDR333 512MB x1 HDD.
LE-370 User ’ s Manual Contact Information Contact Information Any advice or comment about our products and service, or anything we can help you please don’t hesitate to cont act with us. We will do our best to support y ou for your project and business.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Intel LE-370/LE-370Z è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Intel LE-370/LE-370Z - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Intel LE-370/LE-370Z imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Intel LE-370/LE-370Z ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Intel LE-370/LE-370Z, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Intel LE-370/LE-370Z.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Intel LE-370/LE-370Z. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Intel LE-370/LE-370Z insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
