Manuale d’uso / di manutenzione del prodotto 831.1597 del fabbricante Image
Vai alla pagina of 18
Model No. 831.159700 Serial No. Write the serial number in the space above for reference. Serial Number Decal (under seat) EQUIPMENT [,_i I JR :a_'gl n i_.
Important Precautions ................................................................... 3 Before You Begin .................................................... 4 Part dent ficat_on Chart ............ . ............ 5 Assembly .......................
beginning this or any exercise program, consult your physician. This iS especially e of 35or persons with pre-existing health problems. Read all • SEARS assumes no responsibility for personal injury.
man .EQr set ,ecmg me vercame IMAGE" e..e. welgl_t b_nch. The IMAGE" 3.8 is aemgned to help you develop every major muscle group of the body. Whether your goal is a shapely figure, dramatic mus- cle size and strength, or a healthier cardiovascular system, the'IMAGE" 3.
T t_\\_ M6 x 38mm Bolt (60)--1 M6 Washer (30)--5 M8 Washer (52)--10 _\ M8 x 70mm Bolt (41)_ M8 x 65mm Carriage Bolt (59)--4 _\1 M8 x 60mm Bolt (39)--2 M8 x 30mm Bolt (38)--2 M8 x 25ram Bolt (53)--2 M8.
• r _" u Before beginning assembly, carefully read the following Information and Instructions: • Assembly requires two people. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing matedals until assembly is completed.
M10 x 65mm Bolts (42), four M10 Washers (6), and two M10 Nylon Locknuts (11). Do not tighten the Nylon Locknuts yet. Slide the Upright (1) and the Brace (2) onto the M10 x 65mm Carriage Bolts (40) and the M8 x 65mm Carriage Bolts (59) in the left Base (7).
While a second person holds a Crossbar (8)in Me position shown, Insert two M10 x 70mm Bolts (46) through the bracket on the Weight Storage Tube (21), the left Brace (2), and the bracket on the Crossbar (8). Thread an M 10 Nylon Locknut (11 ) onto each Bolt.
Insert the Barbell (35) through the locking Bar (34) until the Barbell Is centered in the Locking Bar. 9. Identify the Left Weight Glider (32) by looking at the position of the round tube. Press a 38ram Bushing (29) into each end of the round tube on the Left Weight Glider (32).
Left Safety Spotter is positioned as shown, the handle. will point toward the center of the bench. Place the Left Safety Spotter (24) on the left Base (7) so it is centered over the indicated hole. Have a second person hold the Locking Bar (34) so that the Left Weight Glider (32) rests on top of the Left Safety Spotter (24).
11 i//_r 5 " Attach the Small Stabilizer (25) to the Bench Frame •.. A I 11- - " (5) with two M10 x 65mm Cardage Bolts (40) and two "_A #'-"_.']'!I M10 Nylon Locknuts (11). Note: There is an inden- _ _'1 iI tation around the holes on one side of the Small '4f "--_F_.
and an M10 Nylon Locknut (11). Note: Do not over- tighten the Nylon Locknut; the Backrest Tubes must pivot easily. Tube 6 27 20. Attach theBackrest (15) to the Backrest Tubes (27) with tour M6 x 55ram Bolts (4) and four M8 Washers (3O). 2O 15 : 27 21.
(37) with two M6 x 16mm Screws (3). Tilt the Seat Support Tube (37) upwards and attach the narrow end of the Seat (14) to the Seat Support Tube with an M6 x 38ram Bolt (60) and an M6 Washer (30). 37 24. Make sure that all parts are properly tightened before you use the weight bench.
Th_ _lori explains how the weight bench Is adjusted. See the Included exercise guide for important Informa- tion abo_ how to perform a variety of exemlses and how to get the greatest benefit from your exercise program. Inspect and tighten all parts each time you use the weight bench.
To raise the Backrest (15), grip the end of the Backrest with one hand and pull it upwanJ. The Backrest Adjustment Frame (36) will automatically lock into one of the tabs on the bracket on the Bench Frame (5). To lower the Backrest (15), grip the end of the Backrest with one hand and pull it slightly upwards.
KeyNo. Qty. Description Key No. Qty. Description 1 2 Upright 34 1 Locking Bar 2 2 Brace 35 1 Barbell 3 2 M6 x 16mm Screw 36 1 Backrest Adjustment Bracket 4 4 M6 x 55mm Bolt 37 1 Seat Support Tube 5 1 .
11 1(3 17 : 17 o 4o' 13 35 19 30 48 28 57 10 34 11 17 28 18 47 33 12 11 7 52 40 54 48 33 8 11 11 / 17 o o i 49 • 29 31.,_ 50 "49 49 "" 49 53 44 43 47 J 11 54 20 49 32 50 29 a 49.
Model No. 831.159700 QUESTIONS? If you find that: • you need help assembling or operating the IMAGE 3.8 • a part is missing • or you need to schedule repair service call our toll-free HELPLINE 1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Image 831.1597 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Image 831.1597 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Image 831.1597 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Image 831.1597 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Image 831.1597, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Image 831.1597.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Image 831.1597. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Image 831.1597 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
