Manuale d’uso / di manutenzione del prodotto ICEU060 del fabbricante Ice-O-Matic
Vai alla pagina of 19
Mile High Equipment 11100 East 45th Av e Denver, Colorado 80239 Part Number 9081291-01 Print Date 11/01 MODEL-ICEU060 ICE UNDERCOUNTER SERIES CUBERS SERVICE AND INSTALLATION MANUAL.
Introduction ICEU060 Page 1 To the ow ner or us er: This pro duct manu al is a s ource o f informatio n about th e install ation, start up, clea ning, m aintenance, and rep air of the product.
Specificatio ns IC EU060 Page 2 Specifications: 24 Hour Bin Storage Basic Maximum Ref Type. Model Number Capacity Capacity Electrical Fuse Size Ounces ICEU060 55 lbs.
Installat ion IC EU060 Page 3 Location: Prior consi deration for the l ocation o f the ice m achine s hall includ e: Installati on locati on to be i ndoor s with a mi nimum r oom te mperature of 50 ° F and with a m aximum room temper ature o f 100 ° F.
Installat ion IC EU060 Page 4 Water Suppl y and Drain Connecti on: 1. The recom mend water supply line is ¼ inch O.D. cop per tubing . The minimum i ncoming w ater pressure shoul d be 20 psig. 2. Connect th e water suppl y tubi ng to the w ater inlet fitting (3/4 h ose threa d) at the r ear of th e icemak er.
Installat ion ICEU060 Page 5 Final Check: 1. Is the cabi net lev el? 2. Have al l the electr ical and pi ping connectio n been made ? 3. Has the v oltage bee n tested a nd checked ag ainst th e nameplat e rating? 4. Is the unit plugged i nto a sep arate electr ical cir cuit? 5.
Init ial Sta rt Up ICEU060 Page 6 1. Open the water supply v alve. 2. Move electrical breaker or switch to the ON position. 3. Remove the front panel. 4. Check the cube size control sha ft, it should be in a preset position. If not, rotate the con trol shaft clockwise until the unit comes on.
Ho w It Wo rks ICEU060 Page 7 Component Description Cube Size Control The Cube size control is located in the front of th e control box, behind the front panel. T he sensing capillary tube of the cube size control is routed out o f the control box into its bulb holder on the evaporator coil.
Component Location ICEU060 Page 8.
Ho w It Wo rks ICEU060 Page 9 Water Sy stem Freezing Cycle The refrigeration process creates cold te mperatures within the evaporator coils and remov es heat from the wat er s pra yed up into t he in vert ed ice cube c ups . W hen enough heat is removed, the w ater changes into ice, and forms where it is the coldest: in the ice cube cups.
Ho w It Wo rks ICEU060 Page 10 Refrigeration Sy stem Freezing Cycle The ice cubes are formed in an inverted mold that is refrigerated. The refrigeration process begins at the co mpressor . There, refrigerant vapor is compressed and flows fr om th e com press or t hroug h the di scha rge li ne as a high temperature, high pressure gas.
Ho w It Wo rks ICEU060 Page 11 Refrigeration Sy stem Harv est Cycle (When the cubes are released) The ice cubes have been formed in an inverted mold that was refri ger a ted. Now the refrigeration system will change to warm the cube mold and release the cubes.
Operat ion an d A djustmen t ICEU060 Page 12 The information shown below covers a wide ran ge of air and water temperatures. It is intended as a guideline only, and is based on data compiled f rom NE W Clean units. Allow a variation from each end of the range g iv en.
Sanitiz ing A nd C leaning ICEU060 Page 13 An Ice-O-Matic ice machine represents a siz able investment of time and money in any company ’s business. In ord er to receive th e be st re turn for tha t investme nt, i t MUS T receive periodic maintenance.
Service Diagnosis ICEU060 Page 14 SYMPTOM POSSIBLE C A USE SUGGESTED CORRECTIO N Unit will not run. Blown fuse or breaker . Replace fuse and check for cause of blown fuse or breaker. Compressor cyles Low voltage. Check voltage at the supply to the interm ittenly.
Component Replacement IC EU060 Page 15 Bin Thermosta t 1. Unplug the icemaker to disconnect electrical power. 2. Remove screws and cabinet front panel. 3. Remove screws and the control box cover, disconnect el ec trical wires from the bin thermostat control.
Component Replacement IC EU060 Page 16 Spray Platf orm 1. Unplug the icemaker to disconnect electrical power. 2. Open ice bin door. 3. Pull out on the left side and remove cur tain assembly. 4. Lift the spray platf o rm up and pull out to get to the water hose at the base of the platform.
Component La y out ICEU060 Page 17.
Wirin g Diag ram ICEU060 Page 18.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Ice-O-Matic ICEU060 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Ice-O-Matic ICEU060 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Ice-O-Matic ICEU060 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Ice-O-Matic ICEU060 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Ice-O-Matic ICEU060, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Ice-O-Matic ICEU060.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Ice-O-Matic ICEU060. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Ice-O-Matic ICEU060 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
