Manuale d’uso / di manutenzione del prodotto PA 1100 del fabbricante Husqvarna
Vai alla pagina of 17
E E E E n n n n g g g g l l l l i i i i s s s s h h h h Sa w attachment P A P A 1100 Accessoir e de sciage P A P A 1100 Suplemento de sierr a P A P A 1100 Oper ator ′ s manual Manuel d’utilisa tio.
2 – English KEY T O SYMBOLS . Symbols W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine .
English – 3 CONTENTS Contents Note the f ollowing bef ore star ting: Husqvarna AB has a policy of continuous product de velopment and therefore reserves the right to modify the design and appearance of products without prior notice. Long-term exposure to noise can result in permanent hear ing impairment.
4 – English SAFETY INSTR UCTIONS Cutting equipment This section describes how you can achie ve maximum clearing capacity and extend the lif e of the cutting attachment through correct maintenance and using the right type of cutting attachment. Only use cutting equipment recommended b y us! See the T echnical data section.
English – 5 SAFETY INSTR UCTIONS Chain • Saw chain pitch (inches). (The distance between three drive links, divided b y two .) • Drive link width (mm/inches) • Number of drive links. Sharpening y our chain and adjusting raker c learance General information on sharpening cutting teeth • Ne ver use a blunt chain.
6 – English SAFETY INSTR UCTIONS • Alwa ys file cutting teeth from the inside face outw ards. Reduce the pressure on the return stroke. File all the teeth on one side of the bar first. Then turn the saw o ver and file the remaining teeth from the other side.
English – 7 SAFETY INSTR UCTIONS 1 Undo the bar nut. 2 Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner . Tighten the chain until it does not sag from the underside of the bar . 3 Use the combination spanner to tighten the blade n ut while holding up the tip of the bar .
8 – English SAFETY INSTR UCTIONS 2 Check that the oil channel in the gear housing is clean. Clean if necessar y . 3 Check that the bar tip sproc ket turns freely . If the chain lubrication system is still not working after carr ying out the abov e checks you should contact y our ser vice workshop.
English – 9 SAFETY INSTR UCTIONS P ersonal pr otection • Alwa ys wear boots and other equipment described under the heading P ersonal protective equipment in the machine’ s Operator’ s Manual. • Alwa ys wear working clothes and heavy-duty long trousers.
10 – English SAFETY INSTR UCTIONS • Alwa ys slow the engine to idle speed after each working operation. Long per iods at full throttle without any load on the engine can lead to serious engine damage. • Alwa ys work at full throttle. • Let the engine drop back to idle speed betw een each cut.
English – 11 WHA T IS WHA T? What is what on the saw attac hment? (Saw attachment with shaft P A 1100) 11 9 1 2 8 6 5 4 10 7 13 12 14 15 3 11 1 Be vel gear 2 Chain lubrication adjustment screw 3 Sha.
12 – English WHA T IS WHA T? What is what on the saw attac hment? (Saw attachment without shaft P A) 10 8 1 2 7 5 4 3 9 6 12 11 13 14 10 1 Be vel gear 2 Chain lubrication adjustment screw 3 Harness .
English – 13 ASSEMBL Y Fitting the cutting head (Saw attachment with shaft P A 1100) • Fit the cutting head on the shaft so that the screw (A) is aligned with the hole in the shaft as shown. • Tighten screw A. • Tighten screw B . CA UTION! Make sure that the drive shaft inside the shaft engages with the cut-out in the cutting head.
14 – English ASSEMBL Y Adjusting the harness Y ou should alwa ys use the har ness with the machine to give maximum control ov er the machine and reduce the risk of f atigue in your ar ms and back. • Put on the harness. • Hook the machine onto the harness suppor t hook.
English – 15 TECHNICAL D A T A T echnical data Note 1: Equivalent sound pressure le vel is calculated as the time-weighted energy total f or sound pressure lev els under various working conditions with the follo wing time distr ibution: 1/2 idling and 1/2 max speed.
16 – English TECHNICAL D A T A EC-dec laration of conformity (Applies to Europe onl y) W e, Husqvarna AB, SE-561 82 Huskv ar na, Sweden, tel +46-36-146500, declare that this saw attachment from 2002.
´®z+H8r¶0_¨ 2004-02-05 ´®z+H8r¶0_¨ 1140248-26 20.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Husqvarna PA 1100 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Husqvarna PA 1100 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Husqvarna PA 1100 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Husqvarna PA 1100 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Husqvarna PA 1100, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Husqvarna PA 1100.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Husqvarna PA 1100. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Husqvarna PA 1100 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
