Manuale d’uso / di manutenzione del prodotto CT16 del fabbricante Husqvarna
Vai alla pagina of 15
CT16 Owner's Manual 601 00 18-54 Reference No. 337411 05/03/95 8 1.1996 Spare P ar ts Piéces Dètachées.
2 SAFETY RULES THESE SAFETY RULES ARE FOR YOUR PROTECTION. READ THEM CAREFULLY LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS ATTENTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED. IMPORTANT SAFETY STANDARDS REQUIRE OPERATOR PRESENCE CONTROLS TO MINIMIZE THE RISK OF INJURY.
3 Record the following information about your unit so that you will be able to provide it in case of loss or theft. CITY: STATE: TELEPHONE: PURCHASE DATE: MODEL NUMBER: / / SERIAL NO.
4 Figure 4 Figure 5 LOWER END OF HANDLE TINE SHIELD MOUNTING CHANNEL FIG. 1-OP on page 6 shows the tiller/cultivator completely assembled. Reference to the right and left hand side of the tiller/cultivator is from the operator's position behind the unit.
5 IMPORTANT: OVERTIGHTENING THE SCREWS ENOUGH TO CHANGE THE SHAPE OF THE HANDLES CAN RESULT IN DAMAGE TO THE ENGINE CASTING. ● Hold the curved head carriage bolt against theoutside of the lower handle while tightening the tee knobs securely. TO INSTALL THE THROTTLE CON- TROL ASSEMBLY ● Place a No.
7 UPPER HANDLE THROTTLE CONTROL LEFT SIDE LOWER HANDLE TINE SHIELD DEPTH ROD/ TRANSPORT WHEELS RIGHT SIDE LOWER HANDLE CULTIVATOR TINES THROTTLE CONTROL - Controls the engine speed and the tine rotation. This tiller/cultivator is equipped with a centrifugal clutch that engages the tine drive system when the engine speed is increased.
8 The operation of this tiller/cultivator can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating the tiller/cultivator. We recommend standard safety glasses or Wide Vision Safety Mask for over your glasses.
9 GAS OIL GAS OIL 1 Gal. 5 oz. 4 Liters .167 L 2 Gal. 11 oz. 8 Liters .333 L 5 Gal. 27 oz. 20 Liters .833 L U. S. S. I. (METRIC) ● Tilt the tiller/cultivator back on the depth rod or transport wheels to raise the tines off the ground.
10 FIGURE 7 DEPTH ROD IN TILLING POSITION FIG. 2-OP TILLING HINTS ● Tilling is digging in, turning over and breaking up packed soil before planting. Loose unpacked soil helps root growth. Best tilling depth is 4 to 6 inches. Tilling will also clear the soil of unwanted vegetation.
11 GENERAL The warranty on this tiller/cultivator does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must main- tain the tiller/cultivator as instructed in this manual.
12 ENGINE AIR CLEANER The air cleaner filter should be cleaned and reoiled after 3 months or 25 hours of operation. Clean more often under dusty conditions. IMPORTANT: The engine can be worn out in a very short period of time if dirt or grit is allowed to enter the engine.
13 LEFT SIDE TINES RIGHT SIDE TINES CLEVIS PINS HAIRPINS FRONT VIEW RIGHT SIDE INDICATOR PROPERLY INSTALLED RIGHT SIDE TINES TINE REPLACEMENT The tiller/cultivator is left hand or right hand as viewed from the operator's position behind the unit.
14 CARBURETOR ADJUSTMENT A dirty air cleaner will cause the engine to run improperly and/or smoke excessively. Be sure the air cleaner is clean before adjusting the carburetor. Never make unnecessary adjustments to the carburetor. The carburetor was set at the factory to operate efficiently under most applications.
15 ● Drain the fuel from the fuel tank into an approved container outdoors, away from open flame. ● Start and run the engine until it stops due to lack of fuel. ● Pull the starter handle slowly until you feel resistance due to compression pressure, then stop.
16 Drain fuel tank. Fill with fresh mixture. Check fuel mix chart and mix fresh fuel. Clean fuel tank. Fuel tank should be half full when starting engine. See carburetor adjustment section. Clean and re-gap plug. Clean and re-oil air cleaner. Blow dirt and debris off top of carburetor.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Husqvarna CT16 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Husqvarna CT16 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Husqvarna CT16 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Husqvarna CT16 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Husqvarna CT16, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Husqvarna CT16.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Husqvarna CT16. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Husqvarna CT16 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
