Manuale d’uso / di manutenzione del prodotto 1330SB-XLSB del fabbricante Husqvarna
Vai alla pagina of 40
1330SB-XLSb Owner's Manual / 96193004100 / 2008-11.
2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces.
3 PRODUCT SPECIFICA TIONS Gasoline Capacity 4.0 Quarts and T ype: Unleaded Regular only Oil T ype SAE 30 (above 40°F) (API SG–SL): SAE 5W -30 or 10W -30 (0° to +40°F) SAE 0W -30 (below 0°F) Oil Capacity: 28 Ounces Spark Plug: Champion QC12YC (Gap: .
4 P ARTS P ACKED SEP ARA TEL Y IN CARTON (1) POWER CORD (198563) (1) DISCHARGE CHUTE (6) SHEAR BOL TS 1/4-20 x 1-3/4 (198636) (6) SP ACERS (198638) (1) WASHER 3/8 (19131316) (1) L OCKNUT 5/16-18 (7511.
5 AS SEMBL Y / PRE-OPERA TION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiarize you with the unit, which will assist you in assembly , operation and maintenance of the product.
6 AS SEMBL Y / PRE-OPERA TION AUGER CONTROL ROD CONTROL ARM RUBBER SLEEVE L OOP OPENING UP FIG. 5 INST ALL AUGER CONTROL ROD (See Figs. 5 and 6) The auger control rod has the short loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.
7 AS SEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TOR HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower .
8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.
9 MEETS A.N.S.I. SAFETY REQUIREMENTS Our snow throwers conform to the standards of the American National Standards Institute. FIG. 10 OPERA TION Drive speed control lever - used to select forward or reverse motion and speed of snow thrower .
10 TO THROW SNOW (See Fig. 15) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow . • Release the auger control lever to stop throwing snow .
11 OPERA TION USING THE CLEAN-OUT TOOL (See Fig. 16) In certain snow conditions, the discharge chute may be- come clogged with ice and snow . Use the clean-out tool to dislodge this blockage. When cleaning, repairing, or in spect ing, make certain all controls are disengaged and the au- ger/impeller and all moving parts have stopped.
12 NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller , which can cause serious personal injury , property dam age or damage to the snow thrower .
13 CAUTION: Alcohol blended fuels (called gas o- hol or using ethanol or methanol) can attract moisture which leads to separation and for ma- tion of acids dur ing storage. Acidic gas can damage the fuel system of an engine while in storage. T o avoid engine problems, the fuel system should be emptied be fore stor age of 30 days or longer .
14 MAINTENANCE LUBRICA TION CHART GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual.
15 MAINTENANCE SNOW THROWER Always observe safety rules when performing main te nance. TIRES • Maintain proper air pressure in both tires (14–17 P .
16 WARNING: T o avoid serious injury , before per- forming any service or ad just ments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key . 3. Make sure the augers and all mov ing parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it can not come in contact with plug.
17 1. REMOVE GASOLINE FROM FUEL T ANK - Drain gasoline from fuel tank into a suitable container , out- doors, away from fire or flame. Wipe up any spilled gasoline.
18 STORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli ance.
19 Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank. 4. Throttle in STOP position.
20 REP AIR P ARTS A UGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 2 (EXPLODED) 2 10 9 1 11 11 3 12 12 4 13 14 15 17 8 7 11 5 6 11 16 18 35 19 21 22 23 24 25 23 22 21 20 36 26 27 28 30 29 31 31 32 33 34 01.
21 REP AIR P ARTS A UGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .
22 REP AIR P ARTS A UGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 2 01.07.016-A 1 532 42 17-26 AUGER ASSEMBL Y 30 LH 2 532 42 17-27 AUGER ASSEMBL Y 30 RH 1 2 3 (5x) 4 (5x) 01.
23 REP AIR P ARTS A UGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 2 3 1 2 3 01.07.007-A 1 532 18 81-70 PL ASTIC RET AINER 2 532 41 18-33 AUGER BALL BEARING 3 532 17 95-82 SCREW 5/16 − 18 X 1.
24 REP AIR P ARTS A UGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 1 2 5 3 4 3 4 1 2 5 3 4 3 4 01.16.001-A KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 532 18 47-47 DRIFT CUTTER BAR 2 872 27 05-06 CARRIAGE BOL T 5/16 − 18 X .
25 REP AIR P ARTS CONTROL P ANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 KEY P ART NO . NO . DESCRIPTION 1 2 4 6 6 *13 *14 *10 *11 *15 6 8 9 *12 3 5 7 16 17 6 6 18 19 19 01.
26 REP AIR P ARTS CONTROL P ANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .
27 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO .
28 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
29 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
30 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
31 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
32 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 01.02.002-F 2 1 8 7 6 5 4 3 1 2 34 33 32 31 30 29 28 27 25 24 29 28 27 36 23 20 13 12 11 10 15 22.
33 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
34 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
35 REP AIR P ARTS CHAS SIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .
36 REP AIR P ARTS WHEELS SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 1 2 01.06.006-A KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 532 42 20-70 WHEEL AS SEMBL Y LH 2 532 42 20-69 WHEEL AS SEMBL Y RH 1 2 01.
37 REP AIR P ARTS WHEELS SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 KEY P ART NO . NO . DESCRIPTION 2 2 1 3 4 5 6 7 8 9 10 11 12 13 14 13 14 12 11 10 9 8 7 6 5 4 3 1 2 2 23 17 19 20 16 18 24 22 21 23 22 15 18 17 16 20 19 21 01.
38 REP AIR P ARTS BAG OF P ARTS SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
39 REP AIR P ARTS DECALS SNOW THROWER - MODEL NO . 1330SB-XLSB (96193004100), PRODUCT NO . 961 93 00-41 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
532 42 35-18 Rev .1 11.21.08 SR Printed in U.S.A. SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free f.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Husqvarna 1330SB-XLSB è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Husqvarna 1330SB-XLSB - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Husqvarna 1330SB-XLSB imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Husqvarna 1330SB-XLSB ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Husqvarna 1330SB-XLSB, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Husqvarna 1330SB-XLSB.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Husqvarna 1330SB-XLSB. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Husqvarna 1330SB-XLSB insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
