Manuale d’uso / di manutenzione del prodotto ProCurve 2610-PWR del fabbricante HP
Vai alla pagina of 464
Management and Configuration Guide 261 0 261 0-PWR Pr oCurv e Switches R. 1 1.XX www .pr ocurve.com.
.
ProCurve Switch 2610 Series Switch 2610-PWR Series December 2007 Management and Configuration Guide.
© Copyright 2007 Hewlett-Packar d Development Company, L.P . The information contained herein is subject to change without notice. Publication Number 5991-8640 December 2007 Applicable Products ProCu.
Contents Product Documentation Software Feature Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii 1 Getting Started Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting and Ending a Menu Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 How To Start a Menu Interface Session . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 How To End a Menu Session and Exit from the Console: . . .
Tasks for Your First Web Browser Interface Se ssion . . . . . . . . . . . . . . . . . 5-7 Viewing the “First Time Install” Window . . . . . . . . . . . . . . . . . . . . . . . . 5-7 Creating Usernames and Passwords in the Browser Interface . . . .
Rebooting the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18 Operating Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22 Multiple Configuration Files . . . . .
8 Configuring IP Addressing Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 CLI: Viewing and Conf iguring TimeP . . . . . . . . . . . . . . . . . . . . . . . . . . 9-16 Viewing the Current TimeP Co nfiguration . . . . . . . . . . . . . . . . . . 9-17 Configuring (Enablin g or Disabling) the TimeP Mode . . . . . . . . 9-18 SNTP Unicast Tim e Polling with M ultiple SNTP Servers .
Configuring Port-Based Priori ty for Incoming Packets . . . . . . . . . . . . . . 10-28 The Role of 802.1Q VLAN Tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-28 Outbound Port Queues and Packet Priori ty Settings . . . . . . . . . . .
Displaying the PoE Statu s on Specific Port s . . . . . . . . . . . . . . . . . . . 11-12 Planning and Implementing a PoE Configuration . . . . . . . . . . . . . . . . . . 11-13 Assigning PoE Ports to VLANs . . . . . . . . . . . . . . . . . . . . . . .
SNMP Version 3 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6 SNMPv3 Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-7 SNMP Version 3 Users . . . . . . . . . . . . . . . . . . .
LLDP and CDP Data Management . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-54 LLDP and CDP Neighbor Data . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-54 CDP Operation and Commands . . . . . . . . . . . . . . . . . . . . . . . . .
B Monitoring and Analyzing Switch Operation Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C Troubleshooting Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLI Administrat ive and Troubleshooting Co mmands . . . . . . . . . . . C-40 Traceroute Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-40 Restoring the Factory-Default C onfiguration . . . . . . . . . . . . . . .
xvi.
Product Documentation Note For the latest version of all ProCurve switch documentation, including release notes covering recently added features, visit the ProC urve Networking website at www .procurve.com . Clic k on T echnical supp ort , and then click on Product manuals .
Product Documentation Software Feature Index For the software manual set supporting your swit ch model, the follow ing feature index indicates wh ich manual to consult fo r information on a given software feature. (Note that some soft ware features are not supported on all switch models.
Product Documentation Feature Management and Configuration Advanced T raffic Management Access Security Guide File T ransfers X - - Friendly Port Names X GVRP - X - IGMP - X - Interface Access (T elne.
Product Documentation Feature Management and Configuration Advanced T raffic Management Access Security Guide Port-Based Access Control - - X Port-Based Priority (802.
Product Documentation Feature Management and Configuration Advanced T raffic Management Access Security Guide VLANs - X - W eb-based Authentication - - X Xmodem X - - xxi.
Product Documentation xxii.
1 Getting Started Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Getting Started Introduction Introduction This Management and Configuration Guide is intended to support the following switches: ■ ProCurve Series 2610 ■ ProCurve Series 2610-PWR This guide describes how to use the command line in terface (CLI), menu interface, and web browser interface to configure, manage, and monitor switch operation.
Getting Started Conventions ■ Square brackets ( [ ] ) indicate optional elements. ■ Braces ( < > ) enclose requir ed elements. ■ Braces within square brackets ( [ < > ] ) indicate a required element within an optional choi ce.
Getting Started Sources for More Information ProCurve(config)# ip default-gateway 18.28.152.1/24 ProCurve(config)# vlan 1 ip address 18.28.36.152/24 ProCurve(config)# vlan 1 ip igmp Port Identity Examples This guide describes software applicable to both chassis- based and stackable ProCurve switches.
Getting Started Sources for More Information Online Help for Menu Figure 1-2. Getting Help in the Menu Interfac e ■ For information on a specific comm and in the CLI, type th e command name follo wed by “h el p”.
Getting Started Need Only a Quick Start? Need Only a Quick Start? IP Addressing If you just want to give th e switch an IP address so that it can communicate on your network , or if you are not using mult iple VLANs, ProCur ve recommends that you use the Switch Se tup screen to quickly configure IP addressing.
2 Selecting a Management Interface Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Advantages of Using the Me nu Interface . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a Management Interface Overview Overview Management interfaces enable you to re configure the switch and to monitor switch status and performance.
Selecting a Management Interface Advantages of Using the Menu Interface Advantages of Using the Menu Interface Figure 2-1. Example of the Console Inte rface Display ■ Provides quick, easy management.
Selecting a Management Interface Advantages of Using the CLI ■ Allows faster na vigation , avoiding delays that occur with slow er display of graphical objects over a web browser interface. ■ Provides more security ; configurat ion information and passwords are not seen on t he network.
Selecting a Management Interface Advantages of Using t he Web Browser Interface Advantages of Using the W eb Browser Interface Figure 2-3. Example of the Web Browser Interface ■ Easy access to the s.
Selecting a Management Interface Advantages of Using ProCurve Manager or ProCurve Manager Plus Advantages of Using ProCurve Manager or ProCurve Manager Plus Y ou can operate ProCurve Manager and ProC .
Selecting a Management Interface Advantages of Using ProCurve Manager or ProCurve Manager Plus Extended RMON and sFlow , users can monitor overall traffic levels, segments with the highest traffic, or even the top users within a network segment.
Selecting a Management Interface Advantages of Using ProCurve Manager or ProCurve Manager Plus 2-8.
3 Using the Menu Interface Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Starting and Ending a Menu Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Menu Interface Overview Overview This chapter describes the following: ■ Overview of the Menu Interface ■ Starting and ending a Menu session (page 3-3)) ■ The Main Menu (page 3-7)) ■.
Using the Menu Interface Starting and Ending a Menu Session Note If the switch has neither a Manag er nor an Operator password, anyone having access to the console interface can operate the console with full manager privileges. Also, if you co nfigure only an Operator password, entering the Operator password en ables full manager privileges.
Using the Menu Interface Starting and Ending a Menu Session How T o Start a Menu Interface Session In its factory default configuration, th e switch console starts with the CLI prompt. T o use the menu interface with Manager priv ileges, go to the Manager level prompt an d enter the menu command.
Using the Menu Interface Starting and Ending a Menu Session Figure 3-1. The Main Menu with Manager Pri vileges For a description of Main Menu fe atures, see “Main Menu Features” on page 3-7).
Using the Menu Interface Starting and Ending a Menu Session Asterisk indicate s a configurati on change that requires a reboot to activate. Figure 3-2.
Using the Menu Interface Main Menu Features Main Menu Features Figure 3-3. The Main Menu View with Manager Privileges The Main Menu gives you access to these Menu interface features: ■ Status and Co.
Using the Menu Interface Main Menu Features ■ Command Line (CLI): Selects the Command Line Interface at the same level (Manager or Operator) that you are accessing i n the Menu interface. (See chapter 4, “Using the Co mmand Li ne Interface (CLI)”.
Using the Menu Interface Screen Structure and Navigation Screen Structure and Navigation Menu interface screens incl ude these three elements: ■ Parameter fields and/or read -onl y information such .
Using the Menu Interface Screen Structure and Navigation T able 3-1. How T o Navigate in the Menu Interface T ask: Action s: Execute an action from the “Actions –>” list at the bottom of the .
Using the Menu Interface Screen Structure and Navigation T o get Help on individual p arameter descriptions. In most screens there is a Help option in the Actions line. Whenever any of the items in the Actions line is high lighted, pres s [H] , and a separate help scree n is displayed.
Using the Menu Interface Rebooting the Switch Rebooting the Switch Rebooting the switch fr om the me nu interface ■ T erminates all current sessions and performs a reset of the operating system ■ .
Using the Menu Interface Rebooting the Switch Rebooting T o Ac tivate Configuration Changes. Configuration changes for most parameters in the menu inte rface become effective as soon as you save them. However , you must reboot the switch in orde r to implement a change in the Maximum VLANs to support parameter .
Using the Menu Interface Menu Features List Menu Features List Status and Count ers • General System Information • Switch Management Add ress Information • Port Status • Port Counters • Addr.
Using the Menu Interface Where To Go From Here Where T o Go From Here This chapter provides a n overview of the menu interf ace and how to use it. The follow ing table indicates where t o turn for detailed information on how to use the individual features av ailable through the menu interface.
Using the Menu Interface Where To Go From Here 3-16.
4 Using the Command Line Interface (CLI) Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Accessing the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Command Line Interface (CLI) Overview Overview The CLI is a text-based command interf ac e for configuring and moni toring the switch. The CLI gives you access to the switch’ s full set of commands while providing the same password pr otection that is used in t he web browser interface and the menu interface.
Using the Command Line Interface (CLI) Using the CLI Startup Conf ig file in no n-volatile memory . If you reboot the swi tch without first using write memory , all change s made since th e last reboot or write memory (whichever is l ater) will be lost.
Using the Command Line Interface (CLI) Using the CLI Caution ProCurve strongly recommends that you configure a Manager password . If a Manager password is not configured, then the Manager level is n o.
Using the Command Line Interface (CLI) Using the CLI Manager Privileges Manager privileges give you three additiona l levels of access: Manager , Gl obal Configuratio n, and Context Confi guration. (See figure .) A " # " cha racter delimits an y Manager prompt.
Using the Command Line Interface (CLI) Using the CLI Changing Interfaces. If you change from the CLI to the menu interface, or the reverse, you will remain at the same privilege lev el. For example, entering the menu command from the Operator leve l of the CLI takes you to the Operator privilege lev el in the menu interface.
Using the Command Line Interface (CLI) Using the CLI How T o Move Between Levels Change in Levels Example of Prompt, Command, and Result Operator level to Manager level Manager level to Global configu.
Using the Command Line Interface (CLI) Using the CLI For example, if you use the menu interf ace to configure an IP address of “ X ” for VLAN 1 and later use the CLI t o co nfigure a different IP ad dress of “ Y ” for VLAN 1, then “ Y ” replaces “ X ” as the IP address for VLAN 1 in the runni ng- config file.
Using the Command Line Interface (CLI) Using the CLI T yping ? at the Manager level produces this listing: When - - MO RE - - appe ars, use the Spa ce bar or [Return] to list additional co mmands. Figure 4-4. Exa mple of the Manager-Level Command Listing When - - MORE - - appears, there are more comma nds in th e listing.
Using the Command Line Interface (CLI) Using the CLI telnet terminal ProCurve(config)# t As mentioned above, if you type part of a command word and press [T ab] , the CLI completes the current wo rd (if you have typed enou gh of the word for the CLI to disti nguish it from other possibilities), incl uding hyphenated exten- sions.
Using the Command Line Interface (CLI) Using the CLI Listing Command Options. Y ou can use the CLI to remind you of the options available for a command by en tering comma nd keyword s follo wed by ? .
Using the Command Line Interface (CLI) Using the CLI Figure 4-6. Exa mple of Context-Sensitive Command-List Help Displaying Help for an Indivi dual Command. Y ou can display Help for any command that is available at the cu rrent context l evel by ent ering enough of the command string to identify th e command, along wi th help.
Using the Command Line Interface (CLI) Using the CLI Figure 4-8. Exa mple of Help for a Specif ic Instance of a Comma nd Note that trying to list the help for an individual command from a privilege level that do es not includ e that command results in an error message.
Using the Command Line Interface (CLI) Using the CLI ProCurve(eth-C5-C8)#? Lists the commands you can use in the port or static ProCurve(eth-C5-C8)#? trunk context, plus the M a n a g e r, O p e r a t o r, a n d context commands you can execute at this level.
Using the Command Line Interface (CLI) Using the CLI VLAN Context . Includes VLAN-specific command s that apply only to the selected VL AN, plus Manager an d Operator comma nds.
Using the Command Line Interface (CLI) CLI Control and Editing CLI Control and Editing Key strokes Function [Ctrl] [A ] Jumps to the first character of the command line. [Ctrl] [B] or [<] Moves the cursor back one character . [Ctrl] [C ] T erminates a task and display s the command prompt.
5 Using the W eb Browser Interface Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Web Browser Interface Overview Overview The W eb browser int erface built into th e switch lets you easily access the switch from a br owser -based PC on your network.
Using the Web Browser Interface General Features General Features The switch includes these we b browser interface features: Switch Conf iguration: • P o r t s • VLANs and Primary VLAN • Fault d.
Using the Web Browser Interface Starting a Web Browser Interface Session with the Switch Starting a W eb Browser Interface Session with the Switch Y ou can start a web browse r session in the followin.
Using the Web Browser Interface Starting a Web Browser Interface Session with the Switch Using ProCurve Manager (P CM) or ProCurve Manager Plus (PCM+) ProCurve Manager and ProCurve Manager Pl us are designed for i nstallation on a network management w orkstation.
Using the Web Browser Interface Starting a Web Browser Interface Session with the Switch First-T ime Install Alert Alert Log Figure 5-1. Exa mple of Status Overview Scre en Not e The above scree n appears somewhat different i f the switch is co nfigured as a stack Commander .
Using the Web Browser Interface Tasks for Your First Web Browser Interface Session T asks for Y our First W eb Browser Interface Session The first time yo u access the web browser interface, there ar .
Using the Web Browser Interface Tasks for Your First Web Browser Interface Session This window is the la unching po int fo r the basi c configur ation you need to perform to set web b rowser interface passwo rds to maintain sec urity and Fault Detecti on policy , which dete rmines the types of messages th at will be displayed in the Alert Log .
Using the Web Browser Interface Tasks for Your First Web Browser Interface Session Figure 5-3. The Device Passwords Win dow T o set the passwords: 1. Access the Device Passwords screen b y one of the .
Using the Web Browser Interface Tasks for Your First Web Browser Interface Session Using the Passwords Figure 5-4. Exa mple of the Password Window in t he Web Browser Interface The manager and operator pa sswords are us e d to control access to all switch interfaces.
Using the Web Browser Interface Tasks for Your First Web Browser Interface Session Online Help for the W eb Browser Interface Online Help is availa ble for the web browser interface. Y ou can use it by clicking on the question mark but ton in the upper r ight corner of any of the web browser interface screens.
Using the Web Browser Interface Support/Mgmt URLs Feature Support/Mgmt URLs Feature The Support/ Mgmt URLs window en ables you to change the W orld W ide W eb Universal Resource Lo cator (URL) for two fu nctions: ■ Support URL – a support in formation site for your switch ■ Manageme nt Server URL – The web site for web browser online Help.
Using the Web Browser Interface Support/Mgmt URLs Feature Support URL This is the si te that th e swit ch accesses w hen you click on the Support tab on the web browser interface. The default URL is: www .procurve.com which is the web si te for ProCurve’ s networking products.
Using the Web Browser Interface Status Reporting Features Status Reporting Features Browser elem ents covered in this sectio n include: ■ The Overv iew window (b elow) ■ Port utilization and statu.
Using the Web Browser Interface Status Reporting Features Policy Management and Configuration. ProCurve PCM can perform network-wid e policy manag ement and configu ration of your sw itch. For more informatio n, refer to the docu mentation provided with the PCM softw are.
Using the Web Browser Interface Status Reporting Features ■ % Error Pkts Rx : All e rror packets received by the port. (This indic ator is a reddish color on many sy stems.
Using the Web Browser Interface Status Reporting Features Figure 5-10. Display of Nume rical Values for the Bar Port Status Port Status Indic ators Legend Figure 5-11. The Port Status Indicators and Legend The Port Statu s indicators sho w a symbol for each po rt that indicate s the general status of the port.
Using the Web Browser Interface Status Reporting Features The Alert Log The web browser interface Alert Log, sh own in the lowe r half of the sc reen, shows a list of network occu rrences, or alerts , that were detected by the switch.
Using the Web Browser Interface Status Reporting Features Alert T ypes and Detailed Views The web browser interface genera tes the following al ert types: • Auto Partitio n • High collision or dro.
Using the Web Browser Interface Status Reporting Features Figure 5-13.Example of Alert Log Detail View The Status Bar The Status Bar is displ ayed in the upper left corner of the web browser interface screen. Figure 5-14 shows an expanded view of the status bar .
Using the Web Browser Interface Status Reporting Features T able 5-1.Status In dicator Key Color Switch Status Status Indicator Shape Blue Normal Activity; "Fir st time installation" information available in the Alert log. Green Normal Activity Y ellow Warning Red C ritical ■ System Name.
Using the Web Browser Interface Status Reporting Features Figure 5-15. The Fault Detectio n Window The Fault Detection screen contai ns a list box for setting fault det ection and response policy . Y ou set the sensit ivity level at which a network problem should generate an alert and send it to the Alert Log.
Using the Web Browser Interface Status Reporting Features ■ Never . Disables the Alert Log and tran smission of aler ts (traps) to the management server (in cases where a network management tool such as ProCurve Manager is in use). Use this op tion when you don’ t want to use the Alert Log.
Using the Web Browser Interface Status Reporting Features 5-24.
6 Switch Memory and Configuration Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch Memory and Configuration Contents Transferring Startup- Config Files To or From a Remote Server . . . . 6-35 Xmodem: Copying a Conf iguration Fil e to a Xmodem: Copying a Configur ation from a Serially TFTP: Copying a Config uration File to a Remote Host .
Switch Memory and Configuration Overview Overview This chapter describes: ■ How switch memory manag es configurat ion changes ■ How the CLI imp l ements config uration changes ■ How the menu int.
Switch Memory and Configuration Overview of Configuration File Management ■ Running Config File: Exists in volatile memory and controls switch operation. If no configu ration changes have been made in the CLI since the switch w as last booted, the r unnin g-config file is identical to the startup- config fi le.
Switch Memory and Configuration Overview of Configuration File Manage ment “permanent”. When you are satisfied that the change is satisfactory , you can make it permanen t by executing the write memory command.
Switch Memory and Configuration Using the CLI To Implement Configuration Changes Using the CLI T o Implement Configuration Changes The CLI offers these capabilities: ■ Access to the full set of swit.
Switch Memory and Configuration Using the CLI To Implement Configuration Changes 3. Observe the switch’ s performance wi th the new parameter settings to verify the effect of your changes. 4. When you are satisfied that you have the correct parameter settings, use the write memory command to copy the changes to the startup- config file.
Switch Memory and Configuration Using the CLI To Implement Configuration Changes ProCurve(config)# interface e 1 disable Disables port 1 in the running confi guration, which cau ses port 1 to bl ock all traffic.
Switch Memory and Configuration Using the Menu and Web Browser Interfaces T o Implement Configuration Changes How T o Reset the startup-config and running-config Files to the Factory-Default Configuration .
Switch Memory and Configuration Using the Menu a nd Web Browser Inte rfaces To Implement Configuration Changes Note The only e xception to thi s operation ar e two VLAN-re lated paramet er changes that require a rebo ot—described under “Rebooting T o Activate Configurat ion Changes” on page 6-12.
Switch Memory and Configuration Using the Menu and Web Browser Interfaces T o Implement Configuration Changes Note If you reconfigure a parame ter in the CLI and then go to the menu interface without executing a write memory command, those changes are stored only in the running configuration.
Switch Memory and Configuration Using the Menu a nd Web Browser Inte rfaces To Implement Configuration Changes Rebooting T o Ac tivate Configuration Changes.
Switch Memory and Configuration Using Primary and Secondary Flash Image Options Using Primary and Secondary Flash Image Options The switch features two flash memory locations for storing switc h software image files: ■ Primary Flash: The default storage for a switch software image.
----- ---------- -------- ------- ------- Switch Memory and Configuration Using Primary and Secondary Flash Image Options For example, if the switch is using a software version of R.01.01 stored in Primary flash, show version produces the followin g: ProCurve(config)# show vers ion Image stamp: /sw/code/build/info (s03) Nov 01 2007 10:50:26 R.
Switch Memory and Configuration Using Primary and Secondary Flash Image Options R.11.XX 104 Boot Image: Primary Procurve(config)# boot system fl ash secondary Device will be rebooted, do you want to continue [y/n]? y . . . ProCurve> show version Image stamp: /sw/code/build/s w Aug 1 2007 12:08:01 R.
Switch Memory and Configuration Using Primary and Secondary Flash Image Options flash and you can either copy the seco ndary image into primary or download another image to primary from an external source .
----- ---------- - ------- ------- ------- Switch Memory and Configuration Using Primary and Secondary Flash Image Options Syntax : copy flash flash < d estination flash > where: destination fla sh = primary or secondary : For example, to copy the image in secondary flash to primary flash: 1.
Switch Memory and Configuration Using Primary and Secondary Flash Image Options 1. First v erify that a usable flash image exists in secondary flash. The most reliable wa y to ensure this is to reb oot the sw itch from t he flash image you want to retain.
Switch Memory and Configuration Using Primary and Secondary Flash Image Options T able 6-2. Comparing the Boot and Reload Com mands Actions Included In Boot? Included In Reload Note Save all Optional, Optional with reload Config changes save d to configuration changes since the last boot or reload with prompt <cr>, when prompt display s.
Switch Memory and Configuration Using Primary and Secondary Flash Image Options Syntax : boot sy stem flash < primary | secondary > For example, to reboot the switch fr om secondary flash when t.
Switch Memory and Configuration Using Primary and Secondary Flash Image Options Figure 6-15. Using Reload wit h Pending Configuration Ch anges Scheduled Reload. If no parameters are entered after the reload command, an immediate reboot is exec uted. The reload at and reload after command information is not saved across reboo ts.
Switch Memory and Configuration Using Primary and Secondary Flash Image Options Operating Notes Default Boot Source. The switch reboots from primary flash by default unless you specify the secondary flash. Boot Attempts from an Empty Flash Loca tion. In this case, the switch aborts the attemp t and displays Image does not exist Operation aborted.
Switch Memory and Configuration Multiple Configuration Files Multiple Configuration Files Action Page Listing and Displaying Startup-Config Files 6-26 Changing or Overriding the Reboot Configuration P.
Switch Memory and Configuration Multiple Configuration Files ■ T ransitions fro m one software release t o another can be performed while maintaining a separate co nfiguration fo r the different software relea se versions.
Switch Memory and Configuration Multiple Configuration Files 1. Reboot the switch through the Primary boot path using th e startup-config file named backu pConfig . 2. Use the CLI to make confi guration ch anges in the running-config file, and then execute write mem .
Switch Memory and Configuration Multiple Configuration Files Listing and Displ aying Startup-Config Files Command Page show config files Below show config < filename > 6 - 2 7 V iewing the Startup-Config File Status with Multiple Configuration Enabled .
Switch Memory and Configuration Multiple Configuration Files ProCurve(config)# show config f iles Configuration files: id | act pri sec | name ---+-------------+------------ --------- 1 | | oldconfig .
Switch Memory and Configuration Multiple Configuration Files Changing the Reb oot Configuration Policy . For a given reboot, the switch automatically re boots from the startup -config f ile a ssigned to the flash location (primary or seconda ry) being used for the curren t reboot.
Switch Memory and Configuration Multiple Configuration Files pressing the Reset button or to a power cycle always uses the software version in primary flash, the oper ator needs t o configur e the switch to always bo ot from primary flash with the startup-config file named minconfig (in memory slot 1).
Switch Memory and Configuration Multiple Configuration Files Managing Startup-Config Files in the Switch Command Page rename config < current-filename > < newname-str > 6 - 3 0 copy config.
Switch Memory and Configuration Multiple Configuration Files Syntax: copy con fig < source-filename > c onfig < target-filena me > This command makes a local co py of an existing startup- .
Switch Memory and Configuration Multiple Configuration Files If you want ed to experiment with co nfiguration c hanges to the software version in secondary fl ash, you could create and assign a separate startup- config file for this pu rpose.
Switch Memory and Configuration Multiple Configuration Files Erasing a Startup-Config File Y ou can era se any of t he startup-co nfig files i n the switch’ s memory slots. In some cases, erasing a file causes the switch to generate a new , default- configuratio n file for th e affected memory slot.
Switch Memory and Configuration Multiple Configuration Files Figure 6-22 illustrates using erase config < filename > to remove a startup-config file.
Switch Memory and Configuration Multiple Configuration Files ■ Boots the switch from primary flash using the ne w startup-con fig file. ProCurve(config)# show config f iles Configuration files: id |.
Switch Memory and Configuration Multiple Configuration Files TF TP: Copying a Configurati on File from a Remote Host Syntax: copy tft p config < dest-file > < ip-addr > < rem ote-file > < pc | unix > Use this command to download a configuration file from a TF TP server to the switch.
Switch Memory and Configuration Multiple Configuration Files Xmodem: Copying a Configur ation from a Serially Connected Host Syntax: copy xmod em config < dest-file > < pc | unix > Use this command to download a configuration file from an Xmodem host to the switch.
Switch Memory and Configuration Multiple Configuration Files 6-38.
7 Interface Access and System Information Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Interface Access: Console/Serial Li nk, Web, and Telnet . . . . . . . . . . . .
Interface Access and System Information Overview Overview This chapter describes how to: ■ View and modify the configuration for switch interface a ccess ■ Use the CLI kill command to terminat e a.
Interface Access and System Information Interface Access: Console/Se rial Link, Web, and Telnet Interface Access: Console/Serial Link, W eb, and T elnet Interface Access Features Feature Default Menu .
Interface Access and System Information Interface Access: Console/Serial Link, Web, and Telnet Menu: Modifying the Interface Access The menu interface enables you to modify these parame ters: ■ Inactivity T ime-ou t ■ Inbound T elnet Enabled ■ W eb Agent Enabled T o Access the Interface Access Parameters: 1.
Interface Access and System Information Interface Access: Console/Se rial Link, Web, and Telnet CLI: Modifying the Interface Access Interface Access Command s Used in This Section show console below [.
Interface Access and System Information Interface Access: Console/Serial Link, Web, and Telnet Outbound T elnet to Another Device. This featur e operates indepen- dently of th e telnet-serve r status and enables you to T elnet to another device that has an IP address.
Interface Access and System Information Interface Access: Console/Se rial Link, Web, and Telnet For example, to use one command to co nfigure the switch with the fol lowing: ■ VT100 operation ■ 19.
Interface Access and System Information Interface Access: Console/Serial Link, Web, and Telnet CLI Local T erminal Mode. T o enable temporary and non-disruptive changes to the terminal mode without f orcing a change in the switch’ s terminal mode configurat ion, use the con sole local-terminal command.
Interface Access and System Information Denying Interface Access by Termi nating Remote Management Se ssions Denying Interface Access by T erminating Remote Management Sessions The switch supp orts up to four management session s.
Interface Access and System Information System Information System Information Sy stem In formation Features Feature Default Menu CLI W eb Sy stem Name switch product name page 7-11 page 7-13 page 7-15.
Interface Access and System Information System Information T ime Zone: The number o f minutes your time zone l ocation is to the W est (-) or East (+) of Coordinate d Universal T ime (formerly G MT). The default 0 means no time zone is configured . For example, Berl in, German y is in the +1 zo ne, whi le V ancou ver , Cana da is i n the -8 zone.
Interface Access and System Information System Information 3. Refer to th e online help pro vided with th is screen for furthe r information on configur ation option s for these f eatures. 4. When you have finished mak ing ch anges to the above parameters, press [Enter] , then press [S] (for S ave ) and return to the Main Menu.
Interface Access and System Information System Information Configure a System Na me, Contact, and Location for the Switch. To help distingui sh one switch from an other , configur e a plain-langua ge identity for the switch.
Interface Access and System Information System Information Reconfigure the Age T ime fo r Learned MAC Addr esses. This com- mand corresponds t o the MAC Age Interv al in the menu interface, and is expressed in seco nds. Syntax : mac-age-time <60 . .
Interface Access and System Information System Information W eb: Configuring System Parameters In the web browser interfac e, you can enter t he follow ing system informatio n: ■ System Name ■ System Loca tion ■ System Contact For access to the MAC Age Interval and the T ime parameters, use the menu interface or th e CLI.
Interface Access and System Information System Information 7-16.
8 Configuring IP Addressing Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 IP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring IP Addressing Overview Overview Y ou can configure IP addressi ng through all of the switch’ s interfaces. Y ou can also: ■ Easily edit a switch co nfiguration fi le to allow downloading t he file to multiple switches wi thou t overwriting each switch’ s unique g ateway and VLAN 1 IP addressing.
Configuring IP Addressing IP Configuration IP Configuration IP Configuration F eatures Feature Default Menu CLI W eb IP Address and Subnet Mask DHCP/Bootp page 8-5 page 8-7 page 8-11 Multiple IP Addre.
Configuring IP Addressing IP Configuration Notes then the switch uses this gateway , even if a di fferent gateway is received via DHCP or Bootp on the primary VLAN. (This i s also true for T imeP and a non- default T ime-T o-Live.) See “Notes” on page 8- 4 and refer to the chapter on Virt ual LANs in the Advanced T raffic Management Guide .
Configuring IP Addressing IP Configuration ■ The IP addressing used in t he switch should be com patible with your network. Th at is, the IP address must be unique and the subnet mask must be appropriate for your IP netw ork.
Configuring IP Addressing IP Configuration For descriptio ns of these parameters, see the online Help fo r this screen. Before using th e DHCP/ Bootp option, refer to “DHCP/Bootp Operation” on page 8-12. Figure 8-1. Example of t he IP Service Con figuration Sc reen without M ultiple VLANs Configur ed 2.
Configuring IP Addressing IP Configuration CLI: Configuring IP Addres s, Gateway , and T ime-T o- Live (TTL) IP Commands Used in This Se ction show ip page 8-7 vlan <vlan-id> ip page 8-8 address ip default-gateway page 8-11 ip ttl page 8-11 V iewing the Current IP Configuration.
Configuring IP Addressing IP Configuration Figure 8-3. Example of Show I P Listing with Non-Def ault IP Addressing Config ured Configure an IP Address and Su bnet Mask.
Configuring IP Addressing IP Configuration Configure Multi ple IP Addresse s on a VLAN (Multinetting). Y ou can configure one prim ary IP address per VLAN and up to seven seco ndary IP addresses for the same VLAN. That is, th e switch enables you to assign up to eight networks to a VLAN.
Configuring IP Addressing IP Configuration If you then wanted to multine t the defau lt VLA N, you wo uld do th e followi ng: The secondary IP addres ses in a VLAN are listed immediately after th e primary IP address for the VL AN.
Configuring IP Addressing IP Configuration Configure the Optional Default Gateway . Using the Global configura- tion level, you can a ssign one default gateway to the switch. Syntax : ip defau lt-gateway <ip-addre ss> For example: ProCurve(config)# ip default-gateway 10.
Configuring IP Addressing IP Configuration through the switch, configure the s witch with an IP add ress and subnet mask compatible with your netw ork. The following table lists the general features available with and without a netwo rk-compatible IP address configu red.
Configuring IP Addressing IP Configuration The DHCP/Bootp Process. Whenever the IP Config para meter in the switc h or in an individual V LAN in the switch is configured to DHCP/Bootp (the default), or when the swit ch is rebooted wit h this conf iguration: 1.
Configuring IP Addressing IP Configuration Bootp Operation. When a Bootp server receives a request it searches its Bootp datab ase for a record entry that matche s the MAC address in the Bootp request from the switch. If a match is found, the conf iguration da ta in the associated database record is returned to the sw itch.
Configuring IP Addressing IP Configuration lg TF TP server address (source of final configuration file) T144 is the vendor-specific “ta g” identif ying the configuration file to download. vm is a required entry that specifie s t he Bootp report format.
Configuring IP Addressing IP Preserve: Retaining VLAN-1 IP Addres sing Across Configuration File Downloads IP Preserve: Retaining VLAN-1 IP Addressing Across Configuration File Downloads IP Preserv e .
Configuring IP Addressing IP Preserve: Retaining VLAN-1 IP Addres sing Across Configuration File Downloads Entering " ip preser ve" in the l ast line o f a configur ation file implements IP Preser ve when the file is downloaded to the switch and the switch r eboots.
Configuring IP Addressing IP Preserve: Retaining VLAN-1 IP Addres sing Across Configuration File Downloads Using figu re 8-7, above, switches 1 - 3 ignore these entries because th e file implements IP Preserve and their current IP addr essing was not acquired thr ough DHCP/Bootp.
Configuring IP Addressing IP Preserve: Retaining VLAN-1 IP Addres sing Across Configuration File Downloads Becaus e switch 4 (figur e 8-7) receiv ed its most recent IP ad dressing from a DHCP/Bootp server , the switch ignores the ip preserve command and implements the IP addressing included in thi s file.
Configuring IP Addressing IP Preserve: Retaining VLAN-1 IP Addres sing Across Configuration File Downloads 8-20.
9 T ime Protocols Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 TimeP Time Synchronizati on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 SNTP Time Synchronization .
Time Protocols Overview Overview This chapter describes: ■ SNTP T ime Protocol Operation ■ T imep T ime Protocol Operation Using time sy nchronizati on ensures a uniform time among int er operating devices. This helps you to manage a nd troubleshoot switch operation by attaching meaningful time da ta to event and error me ssages.
Time Protocols Overview: Selecting a Time Synchronization Prot ocol or Turning Off Time Protocol Operation ular server , it ignores time broad casts from other SNTP servers unless the configurable Poll Int erval expires thre e consecutive times wi thout an update received from the first-detected server .
Time Protocols SNTP: Viewing, Selecting, and Configuring Note that simply selecting a time sync hronization prot ocol does not enable that protocol on the switch u nless you also enable the protocol itself (step 2, above). For example, in the factory-default configu ration, T imeP is the selected time sync hronization method.
Time Protocols SNTP: Viewing, Selecting, and Configuring T able 9-1.SNTP Paramete rs SNTP Parameter Operation T ime Sync Method Used to select eith er SNTP , TIMEP , or None as the time synchronization method.
Time Protocols SNTP: Viewing, Selecting, and Configuring T ime Protocol Sel ection Parameter –T I M E P –S N T P – None Figure 9-1. The Sy stem Informatio n Screen (Defau lt V alues) 2. Press [E] (for E dit ). The cursor moves to the Sy stem Name field.
Time Protocols SNTP: Viewing, Selecting, and Configuring ii. Enter the IP address of the SNTP server you want the switch to use for time synchronization.
Time Protocols SNTP: Viewing, Selecting, and Configuring CLI: V iewing and Configuring SNTP CLI Commands Described in this Section show sntp page 9-8 [no] timesync pages 9-9 and ff., 9-12 sntp broadcast page 9-9 sntp unicast page 9-10 sntp server pages 9-10 and ff.
Time Protocols SNTP: Viewing, Selecting, and Configuring Even though, i n this example, T imeP is the current time sync hronous method, the switch ma intains the SNTP conf iguratio n.
Time Protocols SNTP: Viewing, Selecting, and Configuring 2. Select SNTP as the time synchronization mode . 3. Enable SNTP for Broadcast mode. 4. View the SNTP configuration aga in to verify the configuration.
Time Protocols SNTP: Viewing, Selecting, and Configuring Note Deleting an SNTP server when only one is configured disables SNTP unicast operation. For example, to select SNTP and configur e it with unic ast mode and an SNTP server at 10.
Time Protocols SNTP: Viewing, Selecting, and Configuring Deletes unic ast SNTP server entry . Re-enters the unicast serv er with a non- default proto col version. show sntp display s the result. Figure 9-6. Example of Spec ifying the SNTP Protocol V ersion Numb er Changing the SNTP Poll Interval.
Time Protocols SNTP: Viewing, Selecting, and Configuring Figure 9-7. Example of SNTP with T ime Sychronization Disabled Disabling the SNTP Mode. If you want to prevent SNTP from bei ng used even if selected by timesync (or the Menu interface’ s T ime Sync Method param- eter), configure the SN TP mode as disabled.
Time Protocols TimeP: Viewing, Selecting, and Configuring T imeP: Viewing, Selecting, and Configuring T imeP Feature Default Menu CLI We b view the T imep time synchronization configuration n/a page 9-15 page 9-17 — select T imep as the time synchronization TIMEP page 9-13 pages 9-18 — method ff.
Time Protocols TimeP: Viewing, Selecting, and Configuring Menu: V iewing and Configuring T i meP T o View , Enable, and Modify the T imeP Protocol: 1. From the Main Menu, select: 2. Switch Configuration... 1. Sy stem Information T ime Protocol Sel ection Parameter – TIMEP (the default) –S N T P – None Figure 9-9.
Time Protocols TimeP: Viewing, Selecting, and Configuring • Use the Space bar to select the Manual mode. i. Press [>] to move the cursor to the Server Address field. ii. Enter the IP address of the T ime P server you want the switch to use for time synchronization.
Time Protocols TimeP: Viewing, Selecting, and Configuring This section describes ho w to use the CL I to view , enable, and configure T imeP parameters.
Time Protocols TimeP: Viewing, Selecting, and Configuring Configuring (Enablin g or Disabling) the T imeP Mode Enabling the T imeP mode means to configure i t for either broadcast or unicast mode.
Time Protocols TimeP: Viewing, Selecting, and Configuring The commands and output would appear as follows: 1 2 3 4 show timep display s the T imeP configuratio n and also shows that SNTP is the currently active time synchroniza tion mode.
Time Protocols TimeP: Viewing, Selecting, and Configuring Figure 9-13. Example of Configu ring T imep fo r Manual Operation Changing the T imeP Poll Interval. This command lets you specify how long the switch waits between ti me po lling interva ls. The default is 720 minutes and the range is 1 to 9999 minutes.
Time Protocols SNTP Unicast Time Polling with Multiple SNTP Servers Disabling the T imeP Mode. Disabli ng the T imeP mode means to configur e it as disabled. (Disabling T imeP prevents the switch from using it as the time synchronization protocol, even if it is the selected T i me Sync Method option.
Time Protocols SNTP Unicast Time Polling with Multiple SNTP Servers accordingly , with the lowest decimal val ue assigned as the primary address, the second-lowest decimal value assigned as the next addr ess, and the third- lowest decim al value as the last address.
Time Protocols SNTP Messages in the Event Log Deleting Addresses. T o delete an address, you mu st use the CLI. If there are multiple addresses and you delete on e of them, the switch re-orders the address priority . (See “Address Prioritization” on page 9-21.
Time Protocols SNTP Messages in the Event Log 9-24.
10 Port Status and Basic Configuration Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 Viewing Port Status and Configuring Port Pa rameters . . . . . . . . . . . . . . . 10-3 Menu: Viewing Port Status and Configur ing Port Parameters .
Port Status and Basic Configuration Contents Configuring and Viewing Port-B ased Priority . . . . . . . . . . . . . . . . . . 10-31 Messages Related to Prioritization . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-32 Troubleshootin g Prioritization .
Port Status and Basic Configuration Overview Overview Note On Connecting T ransceivers to Fixed-Configu ration Devices This chapter describes how to view th e current port conf iguration and how to co.
Port Status and Basic Configuration Viewing Port Status and Configur ing Port Parameters T able 10-1. Status and Parameters for Eac h Port T ype Status or Parameter Description Enabled Ye s (default): The port is ready for a network connection. No: The port will not opera te, even if properly connected in a network.
Port Status and Basic Configuration Viewing Port Status and Configuring Port Parameters Status or Parameter Description Mode 10/100/1000Bas e-T : ( Continued ) • Auto-10: Allows the port to negotiate between ha lf-duplex (HDx) and fu ll-dupl ex (FDx) while keeping speed at 10 Mbps.
Port Status and Basic Configuration Viewing Port Status and Configur ing Port Parameters Status or Parameter Description Group Menu Interface: Specifies the static trunk group, if any , to which a port belongs. (menu) or CLI: Appears in the show lacp command output to show the LACP tr unk, if any , to which a port belongs.
In this example, ports A7 and A8 have previously been co nfigured as a trunk group . ----- --------- -- ------- -- ----- ------ ---------- ----- ----- ------ Port Status and Basic Configuration Viewin.
Port Status and Basic Configuration Viewing Port Status and Configur ing Port Parameters Figure 10-2. Example of Port/T runk Settings with a T runk Group C onfigured 2. Press [E] (for E dit ). The cursor moves to the Enabled field for the first port. 3.
Port Status and Basic Configuration Viewing Port Status and Configuring Port Parameters ■ show interface co nfig : Lists a subset of th e data shown by the show interfaces command (above); that is, only the enabled/disabl ed, mode, and flow control st atus for all ports on the switch.
Port Status and Basic Configuration Viewing Port Status and Configur ing Port Parameters Displaying Spanning T ree Configuration Details T o view detailed stati stics on spanning tree operation for different ports, use the show spanning-tree command. Syntax : show spann ing-tree < port-list > detail Lists 802.
Port Status and Basic Configuration Viewing Port Status and Configuring Port Parameters ■ These commands enable and configur e port C8 from the config level: ProCurve(config)# int e c8 enable ProCur.
Port Status and Basic Configuration Viewing Port Status and Configur ing Port Parameters Display s the startup-config file. The broadca st limit setting appears here if configured and saved to the startup-config file by a write memory command. Yo u m u s t reboot the switch to implement the new setting.
Port Status and Basic Configuration Viewing Port Status and Configuring Port Parameters Auto-MDIX was developed for auto-n egot iating devices, and was shared with the IEEE for the developm ent of the IEEE 802.3ab standard. Auto-MDIX and the IEEE 802.
Port Status and Basic Configuration Viewing Port Status and Configur ing Port Parameters mdix is the manual mode setting that configures the port for connecting to either a switch, hu b, or other MDI-X device with a crossover cable, or to a PC or other MDI device with a straight- through cable.
Port Status and Basic Configuration Viewing Port Status and Configuring Port Parameters Per -Port MDI Operatin g Mode Figure 10-7. Example of Disp laying the Current MDI Op erating Mode Note Port Response to Switch Software Updates 1. Copper ports in auto- negotiation still d efault to auto -mdix mode.
Port Status and Basic Configuration Viewing Port Status and Configur ing Port Parameters Figure 10-8 shows sample output from th e show tech transcei vers command.
Port Status and Basic Configuration Jumbo Frames • This switch only supports revision B and above transceivers. Check: www.hp.com/rnd/device_help/ 2_inform for more info. • Self test failure. • Transceiver type not supported in this port. • Transceiver type not supported in this software version.
Port Status and Basic Configuration Jumbo Frames Y ou can enable i nbound jumbo frames on a per -VLAN basis. That is, on a VLAN configured for jumbo tr affic, all ports belonging to that VLAN and operating at 1 Gbps or 10 Gbps allow inbound jumbo frames of up t o 9220 bytes.
Port Status and Basic Configuration Jumbo Frames ■ Jumbo T raffic Sources: A p ort belonging to a jumbo-enabled VLAN can receive inbound j umbo frames through any VL AN to which it b elongs, including non-jum bo VLANs.
Port Status and Basic Configuration Jumbo Frames V iewing the Current Jumbo Configuration Syntax: show vlans Lists the static VLANs configured on the swit ch and includes a Jumbo column to ind icate whic h VLANs are configured to support inbound jumbo traffic.
Port Status and Basic Configuration Jumbo Frames Indicates which sta tic VLANs are configured to enable jumbo packets. Figure 10-10. Example of Listing the VLAN Memberships for a Range o f Ports Syntax: show vlans < vid > This command shows port membership and jumbo configuration for the specified < vid > .
Port Status and Basic Configuration Jumbo Frames Enabling or Disabling Jumbo T raffic on a VLAN Syntax: vlan < vid > jumbo [ no ] vlan < vid > jumbo Configures the specified VLAN to allow jumbo frames on all ports on the switch that belong to that VLAN.
Port Status and Basic Configuration Jumbo Frames This same cond ition generates a Fau l t-Finder message in the Alert log of the switch’ s web browser interfac e, and also inc rements the switc h’ s “Giant Rx” counter .
Port Status and Basic Configuration Jumbo Frames Jumbo-Enable d VLAN VLAN 10 Non-Jumbo VLAN VLAN 20 Port 3 belongs to both VLAN 10 an d VLAN 20. Jumbo packets recei ved inbound on port 3 can be forwarde d out the Non-Ju mbo ports 4, 5, an d 6. 1 5 2 3 4 6 Figure 10-12.
Port Status and Basic Configuration QoS Passthrough Mode QoS Passthrough Mode QoS Passthrough mode is designed to enhance the perf orma nce of line-rate traffic transfers throu gh the switch. This fea ture should only be used in environments where Quality of Service (QoS) is not o f major importance, but where lossless data transfers are key .
Port Status and Basic Configuration QoS Passthrough Mode Note As stated earlier , use of this QoS-Pa ssthroug h-Mode feature generally assumes that QoS tagged frames are not being se nt through the swi tch. The receipt of priority 6 or 7 packets may in fact suffer packet drops depending on the traffic load of non-prior ity 6 or 7 packets.
Port Status and Basic Configuration QoS Passthrough Mode optimized: Consists of two queues; a smaller queue for protocol packets and a larger queu e for all other traffic. typical: Consists of four queues cons isting of a large queue for normal traffic and small queues for protocol and low priorit y traffic.
Port Status and Basic Configuration Configuring Port-Based Prio rity for In coming Packets Configuring Port-Based Priority for Incoming Packets Feature Default Menu CLI We b Assigning a priority level.
Port Status and Basic Configuration Configuring Port-Based Prio rity for Incoming Packets downstream device. If the ou tbound port is not configured as a tagged member of the VLAN, then the tag is stri pped from the pac k et, which then e xits from the switch with out a priority setting.
Port Status and Basic Configuration Configuring Port-Based Prio rity for In coming Packets For example, suppose you have configured port A10 to assign a prio rity level of 1 (low): ■ An untagged pac.
Port Status and Basic Configuration Configuring Port-Based Prio rity for Incoming Packets ■ On a given p ort, an inbound, tagged packet recei ved on the port with a preset priority of 1 - 7 in its t.
Port Status and Basic Configuration Configuring Port-Based Prio rity for In coming Packets For example, suppose you wanted to configure ports A10 -A12 on the switch to prioritize al l untagged, inboun d VLAN traffic as “Low” (priority level = 1; refer to tabl e 10-3 on page 10-2 9).
Port Status and Basic Configuration Using Friendly (Optional) Port Names Using Friendly (Optional) Port Names Feature Default Menu CLI Web Configure Friendly Port Names Standard Port Numbering n/a pag.
Port Status and Basic Configuration Using Friendly (Optional) Port Names ■ T o retain friend ly port names across r eboots, you must save the current running-con figuration t o the startup- config file af ter enterin g the friendly port names. (In the CLI, use th e write mem ory command.
Port Status and Basic Configuration Using Friendly (Optional) Port Names Figure 10-16. Example of C onfiguring One Frien dly Port Name on Mu ltiple Ports Displaying Friendly Port Na mes with Other Por.
Port Status and Basic Configuration Using Friendly (Optional) Port Names For example: Friendly por t names assigned i n previous examples. Ports Without "Friendly" Name Figure 10-17.
Port Status and Basic Configuration Using Friendly (Optional) Port Names Friendly Port Name Figure 10-19. Example of a Friendly Port Name in a Per-Port Statistics Listing For a given port, if a friend.
Port Status and Basic Configuration Using Friendly (Optional) Port Names For example, if you co nfigure port A1 with a frie ndly port name: This command seque nce saves the friendly port name for port A1 in the startup- config file, bu t does not do so for the name en tered for po rt A2.
Port Status and Basic Configuration Uni-Directional Link Detection (UDLD) Uni-Directional Link Detection (UDLD) Uni-directional L ink Detection (UDLD) monitors a link b etween two ProCurve switches and blocks the ports on bot h ends of the link if the link fails at any point between the two devices.
Port Status and Basic Configuration Uni-Directional Link Detection (UDLD) connected ports. UDLD-enabled ports; however , will preve nt traffic from being sent across a bad link by blocking the ports in th e event that either the individual transmitter or receiver for that connection fails.
Port Status and Basic Configuration Uni-Directional Link Detection (UDLD) The follow ing commands all ow you to configu re UDLD via the CLI. Syntax: [no] inte rface < port-list > link-keepalive Enables UDLD on a port or range of ports. T o disable the feature, enter the no form of the command.
Port Status and Basic Configuration Uni-Directional Link Detection (UDLD) Note When at least one port is UDLD-enable d, the switch will forwar d out UDLD packets that ar rive on non-UDL D-configur ed ports out of all othe r non-UDLD- configured ports in the same vlan.
Port Status and Basic Configuration Uni-Directional Link Detection (UDLD) Notes ■ Y ou must configure the same VLANs that will be used for UDLD on all devices acro ss the network; otherw ise, the UDLD link cannot be maintained. ■ If a VLAN ID is n ot specified, then U DLD control pack ets are sent out of the port as untagged pa ckets.
untagged Port Status and Basic Configuration Uni-Directional Link Detection (UDLD) T o display summary information on all UDLD-enabled ports, enter the show link-keepalive c ommand. For example: ProCurve(config)# show link-keepa live Total link-keepalive enabled port s: 4 Port 5 has been disable d by the Sy stem Administrator .
Port Status and Basic Configuration Uni-Directional Link Detection (UDLD) T o displa y detailed UD LD informat ion for specific po rts, enter the show link- keepalive statistics command. For example: Ports 1 and 2 are UDLD- enabled and show the number of he alth check packet s sent and received o n each port.
Port Status and Basic Configuration Uni-Directional Link Detection (UDLD) Configuration W arnings and Event Log Messages W arning Messages. The followin g table shows the warning messages that may be issued and their possible causes, when UDLD is configured for tagged ports.
11 Power Over Ethernet (PoE) Operation Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2 Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Over Ethernet (PoE) Ope ration Overview Overview Power Over Ethernet (PoE ) technology al lows IP telephones, w ireless LAN access points, an d other powered devices (PDs) to receive power and transfer data over existi ng LAN cabli ng.
Power Over Ethernet (PoE) Operation Overview Related Publications This chapter introdu ces general PoE operatio n, PoE configu ration and monitoring comm ands, and event log me ssages related to PoE operation on the ProCurve Series 2610-PWR switches .
Power Over Ethernet (PoE) Ope ration Power Availability and Provisioning Power A vailability and Provisioning Powered Device (PD) Support The switch must have a minimum of 15 .4 watts of unused PoE power available when you connect an 802.3af-compliant PD, regard less of how much power the PD actually uses.
Power Over Ethernet (PoE) Operation Power Availability and Provisioning Power Priority In the default configuration Po E power pr iority is determined by port number , with the lowest num bered port having the highest priority .
Power Over Ethernet (PoE) Ope ration Power Availability and Provisioning Port Priority Setting Configuration Command 1 and Resulting Operation 9 - 12 High This priority class receives p ower only if all PDs on ports with a Critical priority setting are receiving full power .
Power Over Ethernet (PoE) Operation Configuring PoE Operation Configuring PoE Operation By default, PoE suppo rt is enabled on th e switch’ s 10/100Base -TX ports, with the power p riority set to Low and the power threshold set to 80 (%). The followin g commands a llow you to adjust these settings.
Power Over Ethernet (PoE) Ope ration Configuring PoE Ope ration Syntax: interface [e] < po rt-list > power [ critic al | high | low ] Reconfigures the PoE priority level on < port-list >. For a given level, the switch automaticall y prioritizes po rts by port number (in ascending order).
Power Over Ethernet (PoE) Operation Configuring PoE Operation PoE for Pre-802.3a f-standard PDs By default, all Pr oCurve PoE switches support 802.3af-standard PDs. In addition, th e switches cov ered in this g uide have the ability to su pply power to pre-802.
Power Over Ethernet (PoE) Ope ration Configuring PoE Ope ration For informat ion on the meani ng of othe r power status para meters, refer to “V iewing PoE Configuration and Status” on page 11-11.
Power Over Ethernet (PoE) Operation Viewing PoE Configuration and Status V iewing PoE Configuration and Status Displaying the Switch’ s Global PoE Power Status Syntax: show power-management Displays.
Power Over Ethernet (PoE) Ope ration Viewing PoE Configuration and Status Displaying an Overview of PoE Status on All Ports Syntax: show power-management brief Displays the followin g port power status: • Port: Lists all PoE-capable ports on the switch.
Power Over Ethernet (PoE) Operation Viewing PoE Configuration and Status Displaying the PoE Stat us on Specific Ports Syntax: show powe r -manag ement < port-list > Displays the following PoE st.
Power Over Ethernet (PoE) Ope ration Planning and Implementing a PoE Configuration For example, if you wanted to vi ew the Po E status of port 5, you w ould use show power- manageme nt 5 to display th.
Power Over Ethernet (PoE) Operation PoE Event Log Messages ■ MAC Address Security: Using Port Security , you can configure each switch port wit h a unique list of up to eight MAC addresses for devi ces that are authoriz ed to access the network through that port .
Power Over Ethernet (PoE) Ope ration PoE Event Log Messages POE usage is below configured threshold of <1 - 99> % < slot-# > POE usage is below configured threshold of <1-99> % Indic.
Power Over Ethernet (PoE) Operation PoE Event Log Messages POE usage has exceeded threshold of < 1 - 99 > % < slot-# > POE usage has exceeded threshold of < 1 - 99 > % Indicates that.
Power Over Ethernet (PoE) Ope ration PoE Event Log Messages 11-18.
12 Port T runking Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2 Port Status an d Configurati on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2 Port Connectio ns and Configur ation .
Port Trunking Overview Overview This chapter describes creating and modifying p ort trunk groups. This includes non-prot ocol trunks and L ACP (802.3ad) trunks.
Port Trunking Port Status and Configuration The multiple phy sical links i n a trunk behave as one lo gical link Switch 1: Ports c1 - c 4 configured as a port trunk group . p or t c 1 p or t c 2 p or t c 3 p or t c 4 p or t c 5 p or t c 6 p or t c 7 .
Port Trunking Port Status and Configuration LACP Note LACP operatio n requires full-duplex (FDx) lin ks. For most installations, ProCurve recommends that you leave the port Mode settings at Auto (the default). LACP al so operates with Auto-10 , Auto-100 , and Auto-1000 (if negotia - tion selects F Dx); 10FDx , 100FDx , and 1000FDx settings.
Port Trunking Port Status and Configuration T able 12-1. T runk T ypes Used in Static an d Dynamic T runk Groups T runking Method LACP T runk Dynamic Y es No Static Y es Y es T able 12-2. T runk Configuration Proto cols Protocol T runking Options LACP Provides dynamic and static LACP trunking options.
Port Trunking Port Status and Configuration T able 12-3. General Operatin g Rules for Port T ru nks Media: All ports on both ends of a tru nk group must have th e same media typ e and mode (speed and duplex). The switch blocks any trunked links that do not co nform to this rule.
Port Trunking Port Status and Configuration Spanning T ree: Spanning T ree operates as a global setting on t he switch (one instance of Spanning T ree per switch).
Port Trunking Port Status and Configuration Menu: V iewing and Configur ing a Static T runk Group Important Configure port trun king before you connect the trunked links to an other switch, routing switch, or serv er . Otherwise , a broadcast storm co uld occur .
Port Trunking Port Status and Configuration • All ports in a trunk must have the same media type an d mode (such as 10/100TX set to 100FDx, or 100F X set to 100FDx).
Port Trunking Port Status and Configuration 8. Connect the trunked ports on the switch to the correspondi ng ports on the opposite device. If you previousl y disabled any of the trunked ports on the switch, enable them now . (See “Viewing Port Status and Configur- ing Port Parameters ” on page 10-3.
Port Trunking Port Status and Configuration Using a port list specifies, fo r switch ports in a static trun k group, only the ports you want to view . In this case, the command specifies ports A5 through A 7 .
Port Trunking Port Status and Configuration Listing Static LACP and Dynamic LACP T runk Data. This command lists data for only the LACP-configured por ts. Syntax : show lacp In the followi ng example, po rts A1 and A2 have been previously configured for a static LACP trun k.
Port Trunking Port Status and Configuration On the 2610-24 switch you can configure up to twelve port trunk grou ps having up to eight links each (wit h additional standby links if you’re using dynamic LACP). On the 2610-48 switc h you can c onfigure up to twenty -four port trunk groups having up to eight links each.
Port Trunking Port Status and Configuration ProCurve(config)# no trunk c4-c5 Enabling a Dynamic L ACP T runk Group. I n the default port configur a- tion, all ports on the switch are set to LACP Passive .
Port Trunking Port Status and Configuration Caution Unless STP is r unning on your network, removing a port fr om a trunk can result in a loop. T o help prevent a br oadcast storm when you remove a port from a trunk where STP is not in u se, ProCurve recommends that you first disable the port or disconnect the link on that port.
Port Trunking Port Status and Configuration LACP trunk st atus commands include: T runk Display Method Static LACP T runk Dynamic LACP T runk CLI show lac p command Included in listi ng. Included in listing. CLI show tru nk c ommand Included in listing.
Port Trunking Port Status and Configuration T able 12-4. LACP T runk T ypes LACP Port T runk Configuration Operation Dynamic LACP This option automatically establishes an 802.
Port Trunking Port Status and Configuration Default Port Operation In the defaul t configurat ion, all port s are configured for passive LACP . How- ever , if LACP is not conf igured, th e port will no t try to detect a trunk configurat ion and will ope rate as a standard , untrunke d port.
Port Trunking Port Status and Configuration LACP Partner Ye s : LACP is enabled on both ends of the link. Status Name Meaning No: LACP is enabled on the switch , but either LACP is not enabled or the link has not been detected on the opposite device.
Port Trunking Port Status and Configuration ProCurve(config)# int a17 lacp passive Error configuring port A17: LACP and port security cannot be run together. T o restore LACP to the port, you must remove port security and re-enable LACP active or pa ssive.
Port Trunking Port Status and Configuration Easy control meth ods include eith er disabling L ACP on the selected ports o r configuring them to operate in static LACP t runks.
Port Trunking Port Status and Configuration Dynamic LACP T runk Group: Appears in the o utput from the CLI show lacp command. Interface Option Dynamic LACP T runk Group Static LACP T runk Group Static.
Port Trunking Port Status and Configuration Broadcasts, mult icasts, and floo ds from different source addresses are dis- tributed evenly across the links.
Port Trunking Port Status and Configuration 12-24.
13 Configuring for Network Management Applications Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2 Port Status an d Configurati on . . . . . . . . . . . . . . . . . . . .
Configuring for Network Manageme nt Applications Contents LLDP Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-31 Options for Read ing LLDP Informati o n Collected by the Swi tch . . 13-34 LLDP Standards Comp atibility .
Configuring for Network Management Applications Using SNMP Tools To Manage the Switch Using SNMP T ools T o Manage the Switch Overview Y ou can manage the switch via SN MP from a network management statio n running an applicat ion such as ProCurve Manager (PCM) or ProCurve Manager Plus (PCM+).
Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch SNMP Management Features SNMP management features on the switch include: ■ SNMP version 1, version 2c or versio.
Configuring for Network Management Applications Using SNMP Tools To Manage the Switch If you want to restrict acce ss to one or more specifi c nodes, y ou can use the switch’ s IP Auth orized Ma na ger feature. (R efer to the Access Security Guide for your switch.
Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch SNMP V ersion 3 Commands SNMP version 3 (SNMPv3) adds new co mmands to the CLI for configuring SNMPv3 fu nctions . Y ou ca n: ■ Enable SNMPv3 with the snmpv3 ena ble command.
Configuring for Network Management Applications Using SNMP Tools To Manage the Switch SNMPv3 Enable The snmpv3 enable command starts a dialog that performs three functions: enabling the switch to receive SNMPv3 me ssages, configuring the initial users, and, optional ly , to restrict non version- 3 messages to “read only”.
Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch SNMP V ersion 3 Users The second step to using SNMP v3 on the switch is to configure the users that you assign to different groups. T o establish users on the switch: a.
Configuring for Network Management Applications Using SNMP Tools To Manage the Switch [no] snmpv3 group group_ name user user_nam e sec-model <ver1| ver2c | ver3> (— Continued —) user user_name This is the user to be added to the access group.
Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch Then you must set the group access level to the user . This is done with the snmpv3 group command. For more details on the MIBs access for a give group see “Group Access Levels” on page 13-11.
Configuring for Network Management Applications Using SNMP Tools To Manage the Switch Group Access Levels The switch sup ports eight pred efined group access levels. There are four levels for use with version 3 users and four are use d for access by version 2c or version 1 management applications.
Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch SNMP Communities SNMP commuities are supported by the switch to allow management application that use version 2c or version 1 to access the switc h. The communities are mapped to Group Access Levels that are used for version 2c or version 1 supp ort.
Configuring for Network Management Applications Using SNMP Tools To Manage the Switch Figure 13-4 shows the assigning of th e Operator community on MgrStation1 to the CommunityOpe ratorReadWrite group . Any other Operator only has an access level of CommunityOperat orReadOnly .
Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch Caution Deleting or changi ng the community named “p ublic” prevents network management applications (such as auto -discovery , traffic moni toring, SNMP trap generation, and thre shold setting) from op erating in the switch.
Configuring for Network Management Applications Using SNMP Tools To Manage the Switch If you are addi ng a communi ty , the fields in this scre en are blank. If you are editi ng an existing community , the values for the currently selec ted Community appear in the fields.
Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch CLI: V iewing and Configuring SNMP Community Names Community Name Commands Page show snmp-server [<community-s.
Configuring for Network Management Applications Using SNMP Tools To Manage the Switch Configuring Community Na mes and V alues. The snmp-server command enables you to add SNMP communities wi th either defa ult or specific access attributes, and to delete specific c ommunities.
Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch SNMP Notification and T raps The switches covered i n this guide support the SNMP v3 notification pr ocess. They also supp ort version 1or version 2c traps. For more informat ion on version 1 or version 2c traps, see “T rap Features” on page 13-20.
Configuring for Network Management Applications Using SNMP Tools To Manage the Switch [no] snmpv3 targetad dress < addr -name > param s < parms-name> < IP-Addr > ( — Continued — ) max-msg-size<size> The maximum number of bytes of length a message to this target can be.
Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch T rap Features Feature Default Menu CLI We b snmp-server host (trap receiver) public — page — 13-21 snmp-serv.
Configuring for Network Management Applications Using SNMP Tools To Manage the Switch Using the CLI T o List Curre nt SNMP T rap Receivers. This command lists the currently configur ed trap receivers and the setting for authentication traps (along with the current SNMP communit y name data — see “SNMP Communities” on page 13-12).
Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch Note If you specify a community name that doe s not exist—that is, has not ye t been configured on the sw itch—the swit ch still accepts the tra p receiver assignment.
Configuring for Network Management Applications Using SNMP Tools To Manage the Switch If the sending agent does not receive an SNMP response back from the SNMP Manager within the time out period, the inform request may be resent, based on the retry count value.
Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch Sending Event Log Messages as T raps Use the following options to se nd Event Log messages as traps. T able 13-2. Options for Sending Event Log Messages as T raps Event Level Description None (default) Send no log messages.
Configuring for Network Management Applications Using SNMP Tools To Manage the Switch Using the CLI T o En able Authentication T raps. Syntax: [no] snmp-server en able traps authentica tion Enables or disables sending an auth entication tra p to the configured trap receiver(s) if an unauthorized management station attem pts to access the switch.
Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch sFlow agent — A software process that runs as part of the network manage- ment software within a device. The agent packages data i nto datagrams that are forwarded to a central data collector .
Configuring for Network Management Applications Using SNMP Tools To Manage the Switch V iewing sFlow Configuration and Status The following sFlow co mmands allow yo u to display sFlow conf iguration and status via the CLI. Syntax: show sflow agent Displays sFlow agent information.
Configuring for Network Manageme nt Applications Using SNMP Tools To Manage the Switch Note the following details: ■ Destination Address rem ains blank unless it has been con figured. ■ Datagrams Sent shows the number of datagrams sent by the switch agent to the management station since the switc h agent was last enabled.
Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) LLDP (Link-Layer Discovery Protocol) T o standardize device discovery on a ll ProCurve switches, LLDP has been implemented while offering limited read-only support for CDP as documented in this manua l.
Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Also, by using show commands to access the switch’ s neighbor database for informat ion collected by an indivi d.
Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) General LLDP Operation An LLDP packet contains data about t he transmitting switch and port.
Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) T ransmit and Receive Mode. W ith LLDP enable d, the swit ch periodica lly transmits an LLDP advertise ment (packe.
Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) Data T ype Config uration Options Default Description Remote Management Address T ype 4, 6 N/A Alway s Enabled Shows the network address type. Address 4 Default or Uses a default address selection method unless an optional address is Configured configured.
Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Options for Reading LLDP Info rmation Collected by the Switch Y ou can extract LLDP informatio n from the switch to id en tify adja cent LLDP devices.
Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) LLDP Operating Rul es Port T runking. LLDP manages trunked ports individually . That is, trunked ports are configured individually for LL DP operatio n, in the sam e manner as non-trunked por ts.
Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) LLDP Operation and Commands In the default confi guration, LLDP is en abled and in both transmi t and receive mode on all active p orts.
Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) For exam ple, show lldp config produces the following display when the switch is in th e default LLDP conf iguration: Figure 13-15. Example of Viewing the Gene ral LLDP Configuration Note: This value co rresponds to the lldp refresh-interval command (page 13- 39).
Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) The blank IpA ddress field indicates th at the default IP address wi ll be advertised from this port. (Refer to page 13-43: “Configur ing a Remote Management Addre ss for Outbound LLDP Advertise ments” Figure 13-16.
Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) Changing the T ransmission In terval for LLDP Packets. This interval controls how often active ports retransm it advertisements to their neighbors.
Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Changing the Delay Interval Betw een Adve rtisements Generated b y V alue or Status Changes to the LLDP MIB. The switch uses a delay- interval setting to delay transmit ting successive advertisements resulting from these LLD P MIB changes.
Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) Changing the Reinitia liza tion Delay Interval. In the default configuration, a port recei ving a disable command f.
Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) For example, this comm and enables SNMP notification on ports 1 - 5: ProCurve(config)# lldp enable-notification 1-5 Changing the Minimum Interval for Successi ve LLDP Data Change Notifications for the Same Neighbor .
Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) Configuring Per -Port LLDP T ransmit and Receive Modes These commands cont rol LLDP advertisement traffi c inbound and outb ound on active ports.
Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Syntax [ no ] lldp config < port -list > ipAddrEnable < ip-address > Replaces the default IP address for the port with an IP address you specify.
Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) Syntax [ no ] lldp config < port -list > basicTlvEna ble < TLV -T ype > port_descr For outbound LLDP adv ertisements, includes an alphanumeric string describing the port.
Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Displaying Switch Informat ion A vailable for Outbound Advertisements These commands display the current switch inform ation that will b e used to populate outbo und LLDP advertisements.
Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) The Management A ddress field display s only the LLDP-configurabl e IP addresses on the switch.
Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Syntax show lldp info remote-device [ port-list ] Without the [ port-list ] option, this command provides a global list of the individual devices it has detected by reading LLDP advertisements (and also CD P advertisements).
Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) The data shown for port 3 was transl ated from a CDP advertisement from a 53 00xl switch with LLDP disabled. (Not all fields expected b y the LLDP device are populated with the CDP data.
Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Displaying LLDP Statistics LLDP statistics are availabl e on both a global and a per -port levels. Rebooting the switch resets the LLDP statisti cs co unters to zero.
Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) — Continued from the preceding page. — Per -Port LLDP Counters: NumFr amesRec vd: Shows the total number of valid, inbound LLDP advertisements received from any neighbor(s) on < port- list > .
Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Counters showing frames sent on a po rt but no frames received on that port indicates a n active link with a device that either has LLDP disa bled on the link or is not LLDP- aware.
Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) LLDP Operating Notes Neighbor Maximum. The neighb ors table in the switch supports as many neighbors as there are ports on the sw itch.
Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) LLDP and CDP Data Management This section describes poi nts to note regarding LLDP (Link-Layer Discov ery Protocol) and CDP (Ci sco Discovery Protocol) data received by the switch from other de vices.
Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) Note Because ProCurve switches do not gen erate CDP packets, they are not represented in th e CDP data collecte d by an y neighbor devices running CDP .
Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) CDP Operation and Commands By default the switches covered by th is guide have C DP enabled on each port. This is a read-only capability , meanin g that the switch can receive and store information about adjacent CDP devices but does not generate CDP pa ckets.
Configuring for Network Management Applications LLDP (Link-Layer Discovery Protocol) The follow ing example shows the defaul t CDP configuration. CDP Enable/Di sable on the Switch Per -Port CDP Enable/Dis able Figure 13-24. Example of Show CDP w ith the Default CDP Configurati on V iewing the Switch’ s Current CDP Neighbors T able.
Configuring for Network Manageme nt Applications LLDP (Link-Layer Discovery Protocol) Enabling CDP Operati on. Enabling CDP operation (the default) on th e switch causes the switch to add entrie s to its CDP Neighbors table for any CDP packets it rec eives from other neig hboring CDP devi ces.
A File T ransfers Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2 Downloading Switch Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2 General Switch Softw are Download Rules .
File Transfers Overview Overview Y ou can downlo ad new switch sof tware and uplo ad or download sw itch configurat ion files. These features are useful fo r acqu iring periodic switch software upgrad es and for storing o r retrieving a switch configuration.
File Transfers Downloading Switch Software General Switch Softwa re Download Rules ■ A switch software image downloaded through the menu interface alwa ys goes to primary flash. ■ After a switch software down load, you must reboot the sw itch to imple- ment the newly downl oaded code.
File Transfers Downloading Switch Software Note If your TF TP serve r is a Unix workstation, ensure that the case (upper or lower) that you specify for the filename is the same case as the characters in the switch software filenames on the server .
File Transfers Downloading Switch Software Progress Bar Figure A-2. Ex ample of the Down load OS Screen During a Download A “progress” bar indicates the progre ss of th e download . When the entire switch software file has been received , all activity on the swi tch halts and you will see Validating and writing sy stem software to FLASH.
File Transfers Downloading Switch Software CLI: TF TP Download from a Server to Primary or Secondary Flash This comman d automaticall y downloads a swit ch software im age to primar y or secondary flash.
File Transfers Downloading Switch Software Using Secure Copy and SF TP For some situ ations you may want to us e a secure meth od to issue co mmands or copy files to the switch. By op en ing a secure, encrypted SSH se ssion you can then use a third-party software app lication to take advantage of Secure Copy (SCP) and Se cure ftp (SF TP).
File Transfers Downloading Switch Software Note SF TP over SSH version 1 (S SH v1) is no t supporte d. A request from either the client or the switch (or both) using SSH v1 generate s an error message. The actual text of th e error message diffe rs, depending on the client softw are in use.
File Transfers Downloading Switch Software The SCP/SF TP Process T o use SCP and SF TP: 1. Open an SSH sessio n as you normall y would to esta blish a secure encrypted tunnel between y our co mputer and the switch.
File Transfers Downloading Switch Software Authentication Switch mem ory allow s up to ten public keys. This means the authentication and encryption keys you us e for your th ird-party clien t SCP/SF T P software can differ from the keys you use for the SSH session, even thou gh both SCP and SF TP use a secure SSH tunnel.
File Transfers Downloading Switch Software ■ All files have read-write pe rmission. Several SF TP commands, such as create or remove , are not allowed and return an error message.
File Transfers Downloading Switch Software 7. Download OS 2. Press [E] (for E dit ). 3. Use the Space bar to select XMODEM in the Method field. 4. Press [Enter] , then [X] (for eX ecute ) to begin th e switch softwa re download. The following message then appears: Press enter and then initia te Xmodem transfer from the attached computer .
File Transfers Downloading Switch Software Note that i f you do not speci fy the flash d estination, the Xmodem download defaults to p rimary flash. For exampl e, to download a swi tch soft ware file name d G0103.swi from a PC (running a terminal emulator pro gram such as HyperT erminal) to primary flash: 1.
File Transfers Downloading Switch Software Switch-to-Switch Download Y ou can use TF TP to transfer a switch software file between two ProCurve switches that use the same software code base. The menu interface enables you to transfer pr imary-to-primary or secondar y-to-primary .
File Transfers Downloading Switch Software General Sy stem Information b. Check the Firmware revision line. CLI: Switch-T o-Switch Downloads Y ou can down load a switch software fil e between t wo switches th at use the same code base and which are connect ed on your LAN.
File Transfers Downloading Switch Software If you do not specify either a primar y or secondary flash location for the destination, th e down load automati cally go es to primary flash. For example, to download switch softwa re from secondary flash in a switch with an IP address of 10.
File Transfers Troubleshooting TFTP Downloads T roubleshooting TF TP Downloads When using the menu interface, if a TF TP download f ails, the Do wnload OS screen indicates the failure.
File Transfers Transferring Switch Configurations ■ For a Unix TF TP server , the file permi ssions for the switch software file do not allow th e file to be cop ied.
File Transfers Transferring Switch Configurations TF TP: Copying a Configuration File to a Remote Host. Syntax: cop y < startup-config | r unning-config > tftp < ip-addr > < remote-file > This command copi es the switch’ s startup conf iguration (startup-confi g file) to a remote TF TP host.
File Transfers Transferring Switch Configurations Xmodem: Copying a Configuration Fi le from a Serially Connected PC or Unix W orkstation. T o use this method, the sw itch must be connected via the serial port to a PC or Unix workst ation on which is stored the configuratio n file you want t o copy .
File Transfers Copying Diagnostic Data to a Remote Host, PC, or Unix Workstation Copying Diagnostic Data to a Remote Host, PC, or Unix W orkstation Y ou can us e the CLI to cop y the follow ing types .
File Transfers Copying Diagnostic Data to a Remote Host, PC, or Unix Workstation Copying Event Log Output to a Destination Device This command uses TF TP or Xmodem to copy th e Event Log conte nt to a PC or UNIX workstation on the network.
File Transfers Copying Diagnostic Data to a Remote Host, PC, or Unix Workstation Copying Crash Log Data Content to a Destination Device This command uses TF TP or Xmodem to copy the Crash Log content to a PC or UNIX workst ation on the net work. Y ou can copy i ndividual slot inform ation or the master switch information.
File Transfers Copying Diagnostic Data to a Remote Host, PC, or Unix Workstation A-24.
B Monitoring and Analyzing Switch Operation Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 Status and Counters Data . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Monitoring and Analyzi ng Switch Operation Contents Menu: Configu ring Port and Static Tr unk Monitoring . . . . . . . . . . . B-24 CLI: Configu ring Port and Stat ic Trunk Mo nitoring . . . . . . . . . . . . . B-26 Web: Configuring Port Monitoring . .
Monitoring and Analyzing Switch Operation Overview Overview The switch has several built-in tools for monitoring, analyz ing, and trouble- shooting switch and network operation: ■ Status: Includes o.
Monitoring and Analyzi ng Switch Operation Status and Counters Data Status and Counters Data This section describes the status and counters screens available through the switch console interface and/or the web browser interface. Note Y ou can access all console scre ens from the web browser interface via T el net to the console.
Monitoring and Analyzing Switch Operation Status and Counters Data Menu Access T o St atus and Counters Beginning at the Main Menu, displa y th e Status and Counters menu by select- ing: 1. Status and Counte rs Figure B-1. The Status and Counters Menu Each of the above menu items accesses the read-only scr eens de scribed on the followin g pages.
Monitoring and Analyzi ng Switch Operation Status and Counters Data General System Information Menu Access From the console Main Menu, select: 1. Status and Counte rs 1. General Sy stem Information Figure B-2. Example of General Switch Inf ormation This screen dynamically indicates how individual switch resources are being used.
Monitoring and Analyzing Switch Operation Status and Counters Data Switch Management Address Information Menu Access From the Main Menu, select: 1 Status and Counte rs .
Monitoring and Analyzi ng Switch Operation Status and Counters Data Module Information Use this feature to dete rmine whic h slots have modu les installed and wh ich type(s) of modules a re installed . Menu: Displaying Port Status From the Main Menu, select: 1.
Monitoring and Analyzing Switch Operation Status and Counters Data Port Status The web browser interface and the co ns ole interface show the same port status data. Menu: Displaying Port Status From the Main Menu, select: 1. Status and Counte rs . . .
Monitoring and Analyzi ng Switch Operation Status and Counters Data V iewing Port and T runk Gr oup Statistics and Flow Control Status Feature Default Menu CLI Web viewing port and trunk statistics fo.
Monitoring and Analyzing Switch Operation Status and Counters Data Menu Access to Port and T runk Statistics T o access thi s screen from the Main Menu, select: 1.
Monitoring and Analyzi ng Switch Operation Status and Counters Data CLI Access T o Port and T runk Group Statistics T o Display the Port Counter Summary Report. This command provides an overview of port activity for all ports on t he switch. Syntax : show interfaces T o Display a Detailed T raf fic Summary for Specific Ports.
Monitoring and Analyzing Switch Operation Status and Counters Data Menu Access to the MAC Address V iews and Searches Per -VLAN MAC-Address V iew ing and Searching. This feature lets you determin e which switch p ort on a sele cted VLAN is being used to communi- cate with a specifi c device on the netw ork.
Monitoring and Analyzi ng Switch Operation Status and Counters Data Finding the Po rt Connection for a Specific Device on a VLAN. This feature uses a device’ s MAC address that you enter to identify the port used by that device. 1. Proceeding from figure B-8, press [S] (for S earch ), to display the following prompt: Enter MAC address: _ 2.
Monitoring and Analyzing Switch Operation Status and Counters Data Prompt for Selecti ng the Port T o Search Figure B-10. Listing MAC Addresses for a Specific Po rt 2. Use the Space bar to select the port you want to list or search for MAC addresses, then press [Enter] to list the MAC addresses detected on that port.
Monitoring and Analyzi ng Switch Operation Status and Counters Data Corresponding Port Numbers. For example, to list the learned MAC address on ports A1 through A4 and p ort A6: ProCurve> show mac-address a1-a4,a6 T o List All Learned MAC Addresse s on a VLAN, with Their Port Numbers.
Monitoring and Analyzing Switch Operation Status and Counters Data Spanning T ree Protoc ol (STP) Information Menu Access to STP Data From the Main Menu, select: 1. Status and Counte rs . . . 8. Spanning T r ee Informatio n STP must be enabled on the switch to display the following data: Figure B-12.
Monitoring and Analyzi ng Switch Operation Status and Counters Data Figure B-13. Example of STP Port Information CLI Access to STP Data This option lists the STP configurat ion, root data, an d per -port data (cost , priority , state, and designated bridge).
Monitoring and Analyzing Switch Operation Status and Counters Data Internet Group Management Protocol (IGMP) Status The switch uses the CLI to display th e follo wing IG MP st atus on a per -VLAN basi.
Monitoring and Analyzi ng Switch Operation Status and Counters Data VLAN Information The switch uses the CLI to disp lay the following VLAN status: Syntax: show vlan Lists: • Maximum number of VLANs.
Monitoring and Analyzing Switch Operation Status and Counters Data Listing the VLAN ID (VID) and Status for ALL VLANs in the Switch. Figure B-15. Example of VLAN Listing for the Entire Swi tch Listing the VLAN ID (VID) an d Status for Sp ecific Ports.
Monitoring and Analyzi ng Switch Operation Status and Counters Data W eb Browser Interface Status Information The “home” screen for the w eb browse r interface is the Status Overview screen, as shown below .
Monitoring and Analyzing Switch Operation Port and Static Trunk Monitoring Features Port and Static T runk Monitoring Features Port Monitoring Features Feature Default Menu CLI We b display monitoring.
Monitoring and Analyzi ng Switch Operation Port and Static Trunk Monitoring Features Menu: Configuring Port an d Static T runk Monitoring This procedure describes co nfiguring the switch fo r monitoring when moni - toring is disabl ed. (If monito ring has already bee n enabled, the screens will appear differently than sh own in this procedure.
Monitoring and Analyzing Switch Operation Port and Static Trunk Monitoring Features Move the cursor to th e Monitoring Port paramete r . Port where monitored tra ffic exits the switch. Figure B-20. How T o Select a Moni toring Port 5. Use the Space bar to select the port to use for monitoring.
Monitoring and Analyzi ng Switch Operation Port and Static Trunk Monitoring Features CLI: Configuring Port an d Static T runk Monitoring Port and Static T runk Monitoring Commands Used in This Section.
Monitoring and Analyzing Switch Operation Port and Static Trunk Monitoring Features T o turn of f monitoring : ProCurve(config)# no mirror-port Selecting or Removing Ports and Static T runks As Monitoring Sources.
Monitoring and Analyzi ng Switch Operation Port and Static Trunk Monitoring Features W eb: Configuring Port Monitoring To e n a b l e p o r t monitoring: 1. Click on the Configuration tab. 2. Click on Monitor Port . 3. T o monitor one or m ore ports. a.
C T roubleshooting Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3 Troubleshooting Approaches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3 Browser or Telnet Access Problems .
Troubleshooting Contents Displaying the Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-37 CLI: Viewing the Configuration File . . . . . . . . . . . . . . . . . . . . . . C-37 Web: Viewing the Conf iguration File . . . . .
Troubleshooting Overview Overview This chapter addresses performance -re lated network probl ems that can be caused by topology , switch configuration, and the effects of oth er devices or their config urations on sw i tch operation.
Troubleshooting Troubleshooting Approac hes ■ Check the network cables – Cabling proble ms are a frequen t cause of network faults. Check the cables for damage, correct type, and p roper connections. Y ou should also use a cabl e tester to check your cables for compliance to the rel evant IEEE 802.
Troubleshooting Browser or Telnet Access Problems Browser or T elnet Access Problems Cannot access the we b browser interface: ■ Access may be disabled by the Web Agent Enabled parameter in the switch console. Check the se ttin g on this p arame ter by selecting: 2.
Troubleshooting Browser or Telnet Access Problems Cannot T elnet into the switch console from a sta tion on the network: ■ T elnet access may be disa bled by the Inbo und T e lnet Enabled parameter i n the System Informati on scr een of the menu interface: 2.
Troubleshooting Unusual Network Activity Unusual Network Activity Network activity that fails to meet ac cepted norms may indicate a hardware problem with one or more of the ne twork components, possibl y including the switch.
Troubleshooting Unusual Network Activity This can also happen, for example, if the server is first conf igured to issue IP addresses with an unlimited durat ion, th en is subsequently co nfigured to issue IP addresses that will expire aft er a limited duration.
Troubleshooting Unusual Network Activity Filter T raffic. The IGMP feature does not operate if the switch or VLAN does not have an IP address configured manually or obtained t hrough DHCP/ Bootp.
Troubleshooting Unusual Network Activity There can be several reasons for not recei ving a response to an authentication request. Do the following: ■ Use ping to ensure that the swi tch has access to the configured RADIUS servers. ■ V erify that th e switch is usi ng the correct encryption ke y (RADIUS secret key) for each server .
Troubleshooting Unusual Network Activity unauthori zed . 802.1X is not active on the switch. After you execute aaa port- access authentic ator active , all ports configured wit h contro l unauthorize d should be listed as Clos ed . Port A9 shows a n “Open” status even though Access Co ntrol is set to Unauthorize d (Force Auth).
Troubleshooting Unusual Network Activity Global RADIUS Enc ryption Key Unique RADIUS Encr yption Key for the RADIUS server at 10.33.18.119 Figure C-2. Example of How T o List th e Global and Server-Specific Radius Encryption Ke y s Also, ensure that the swit ch port used to access the RADIUS server is not blocked by a n 802.
Troubleshooting Unusual Network Activity Radius-Related Problems The switch does not receive a res ponse to RADIUS authentication requests. In this case, the switch wi ll attempt authen tication using the secondary method configured for the type of access you are using (console, T elnet, or SSH).
Troubleshooting Unusual Network Activity Spanning-T ree Protocol (STP) and Fast-Uplink Problems Caution If you e nable STP , it is recommen ded that you leave the remai nder of the STP parameter settings at their default va lues until you have had a n opportunity to evaluate STP performance in your ne tw ork.
Troubleshooting Unusual Network Activity SSH-Related Problems Switch access refused to a client. Even though you have placed the cli- ent’ s public key in a t ext file and copied the file (using the copy tftp pub -key- file command) into the switch, the switch refuses to allow the client to have access.
Troubleshooting Unusual Network Activity The public key file you are trying to d ownload has one of the follow ing problems: ■ A key in the file is too long. The ma ximum key length is 1024 characters, including spaces. This co uld also mean that two or more keys are merged together instead of being separated by a <CR><LF>.
Troubleshooting Unusual Network Activity memory to save the authentic ation configu ration to flas h, then pressing the Reset bu tton or cycling the power rebo ots the switch with the boot -up config uration.
Troubleshooting Unusual Network Activity ■ The access attempt is outside of the time frame allowed for the account. ■ The allowed number of concurrent logins for the account has been exceeded For more help, refer to the documentati on provided with you r T ACACS+ server application.
Troubleshooting Unusual Network Activity None of the devices assi gned to one or more VLANs on an 8 02.1Q- compliant switch are being recognized. If multiple VLANs are being used on ports connec ting 802.1Q -compliant devices, inconsistent VLAN IDs ma y have been assigned to one or more VLANs.
Troubleshooting Unusual Network Activity Note that attempting to creat e redundant paths through the use of VLANs wil l cause problems with some switches. On e symptom is th at a duplicate MAC address appears in the Port Addre ss T abl e of one port, and then later appears on another port.
I I Troubleshooting Using Logging To Identify Problem Sources Using Logging T o Identify Problem Sources Event Log Operation The Event Log records operating events as single-line entries listed in ch rono- logical order , and serves as a tool for isolating problems.
Troubleshooting Using Logging To Identify Problem Sources (The event log is not erased by using the Reboot Swi tch command in the Main Menu.) T able C-1.
Troubleshooting Using Logging To Identify Problem Sources Menu: Entering and Navigating in the Event Log From the Main Menu, select Event Log . Range of Events in the Log Range of Log Ev ents Displayed Log Status Line Figure C-7.
Troubleshooting Using Logging To Identify Problem Sources CLI: Using the CLI, you can list ■ Events recorde d since the last boot of the sw itch ■ All events recorded ■ Event entries containing .
Troubleshooting Using Logging To Identify Problem Sources Debug and Syslog Operation Y ou can direct switch debug (Event log) messages to th ese destinations: ■ Up to six SyslogD servers ■ One management-access session through: • A direct-connect RS-232 console CLI session • A T elnet session • An SSH session Figure C-8.
Troubleshooting Using Logging To Identify Problem Sources Debug T ypes This section describ es the types of de bug messages the switch can send to configured debug destinations. Syntax: [no] debug < debug-type > all Configures the switch to send all debug types to the confi g- ured debug destination(s).
Troubleshooting Using Logging To Identify Problem Sources Configuring the Switch T o Send Debug Messages to One or More SyslogD Servers Use the logging command to configure th e switch to send Syslog messages to a SyslogD server , or to remove a SyslogD server from the s witch co nfiguration.
Troubleshooting Using Logging To Identify Problem Sources For example, on a switch where there ar e no SyslogD servers configured, yo u would do the foll owing to configure SyslogD servers 18.120.3 8.155 and 18.120.43.125 and automatically enable Syslog logging (with user as the defaul t logging facility): ProCurve(config)# logging 18.
Troubleshooting Using Logging To Identify Problem Sources Enabling or Disab ling Logging to Management Sessions and SyslogD Servers. Use this command when you want to do any of the following: ■ Disable Syslog log ging on all currently c onfigured SyslogD servers wi th- out removing the servers from the switch con figuration.
Troubleshooting Using Logging To Identify Problem Sources Shows that Sy slog (Destination) logg ing is enabled and transmitting log messages to IP address 18.120.38.155. Also shows that the logging facil ity is set to use r (the default), and that session logging is enable d.
Troubleshooting Using Logging To Identify Problem Sources Syntax : show debug List the current debug status for both Syslog logging and Session logging. Shows that Sy slog logging is enabled and sending even t messages to the user facility on the S y slogD server at IP address 18.
Troubleshooting Diagnostic Tools server , ensure that the server’ s Syslog application is configure d to accept the “debug” severity level. (The default configurati on for some Syslog applications ignores the “debug” severity level.) ■ A reboot temporarily suspends Syslog lo gging.
Troubleshooting Diagnostic Tools Ping and Link T ests The Ping test and the Link test are po int-to -point te sts be twee n your switch and another IEEE 802.3-compliant device on your ne twork. These tests can tell you whet her the switch is co mmunica ting properly with another device.
Troubleshooting Diagnostic Tools W eb: Executing Ping or Link T ests 2. Click he re. 1. Click here. 3. Select Ping T est (the default) or Link T est 4. For a Ping test, enter the IP address of the target device . For a Link test, enter the MAC address of the target device.
Troubleshooting Diagnostic Tools Number of Packets to Se nd is the number of ti mes you want the swit ch to attempt to test a c onnection. T imeout in Seconds is the number of seconds to allow per attempt to test a connection before determining that the current at tempt has failed.
Troubleshooting Diagnostic Tools Link T ests. Y o u can issue single or multiple link tests with v arying repeti- tions and timeo ut periods. The de faults are: ■ Repetitions: 1 (1 - 999 ) ■ T ime.
Troubleshooting Diagnostic Tools Displaying the Configuration File The complete switc h configuratio n is co ntained in a file that you can browse from either the we b browse r interface or the CLI. It may be useful in some troubleshooting scenar ios to view the switch configurat ion.
Troubleshooting Diagnostic Tools Listing Switch Configuration and Operation Details for Help in T roubleshooting The show tech command outputs, in a single listing, switch op erating and running confi.
Troubleshooting Diagnostic Tools 1. In Hypertermin al, click on T r ansfer | Capture T ext... Figure C-16. The Capture T e xt window of the Hypertex t Application Use d with Microsoft Windows Softw are 2. In the File field, enter the path and file name under w hich you want to store the show tech output.
Troubleshooting Diagnostic Tools CLI Administrative and T roubleshooting Commands These command s provide info rmation or perform actions that you may find helpful in troubl eshooting o perating problems with th e switch. Note For more on the CLI, refer to “Using the Command Line Interface (CLI)” on page 4-1.
Troubleshooting Diagnostic Tools Syntax: traceroute < ip-address > Lists the IP addre ss of each hop in the route, plus the time in microseconds for the traceroute packet reply to the switch for each hop. T o halt an ongoing traceroute search, press the [Ctrl] [C] key s.
Troubleshooting Diagnostic Tools Intermediate rou ter hops with the time taken for the switch to receive acknowledg ement of each probe re aching each router .
Troubleshooting Diagnostic Tools Executing traceroute where the route becomes blocked or ot herwise fails results in an output marked by timeout s for all probes beyond the last detected hop.
Troubleshooting Restoring the Factory-Default Configuration Restoring the Factory-Default Configuration As part of your troubleshooting pr ocess, it may become necessary to return the switch configuration to the factor y default settings.
Troubleshooting Restoring a Flash Image Restoring a Flash Image The switch can lose it s op erating system if either the primary or secondary flash image location is empty or contains a corrupted OS file and an operator uses the erase flash command to erase a good O S image file from the opposite flash location.
Troubleshooting Restoring a Flash Image 4. Since the OS file is l arge, you can increase the speed of the download by changing the switch console and termin al emulator baud ra tes to a high speed. For example: a. Change the switch baud rate to 115,2 00 Bps.
Troubleshooting Restoring a Flash Image Figure C-21. Example of Xmodem Do wnload in Progress 8. When the download completes, the switch reboots from primary flash using the OS image you dow nloaded in the precedi ng steps, plus th e most recent startup-config file.
Troubleshooting Restoring a Flash Image C-48.
D MAC Address Management Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2 Determining MAC Addresses in the Switch . . . . . . . . . . . . . . . . . . . . . . . . D-2 Menu: Viewin g the Switch’s MAC Addre sses .
MAC Address Management Overview Overview The switch assigns MAC addresses in these areas: ■ For management functions: • One Base MAC address assigned to the default VLAN (VID = 1) • Additional M.
MAC Address Management Determining MAC Addresses in the Switch ■ Use the CLI to view the switch’ s port MAC addresses in hexadecimal format. Menu: V iewing the Switch’ s MAC Addresses The Manage.
MAC Address Management Determining MAC Addresses in the Switch CLI: Vi ewing the Port and VLAN MAC Addresses The MAC address assigned to each switch port is use d internally by su ch features as Flow Control and the Spanning T ree Protocol.
MAC Address Management Determining MAC Addresses in the Switch ifPhy sAddress.1 - 6:Ports A1 - A6 in Slot 1 (Addresses 7 - 24 in slot 1 and 25 - 48 in slot 2 are unused.) ifPhy sAddress.49 - 51:Ports C1 - C3 in Slot 3 (Addresses 52 - 72 in slot 3 are unused.
MAC Address Management Viewing the MAC Addresses of Connected Devices V iewing the MAC Addresses of Connected Devices Syntax: show mac-address [ | mac-addr | Lists the MAC addresses of the de vices the switch ha s detected, along with the number of the specific port on which each MAC address w as detected .
MAC Address Management Viewing the MAC Addresses of Connected Devices T o list the MAC addresses of devices the switch has detected, use the show mac-address command.
MAC Address Management Viewing the MAC Addresses of Connected Devices D-8.
E Daylight Savings T ime on ProCurve Switches Configuring Daylight Savings T ime This informat ion applies to the following Pro Curve switch es: • 2512 • 2824 • 1600 M • ProCurve • 2524 • .
Daylight Savings Time on ProCurve Switches Configuring Daylight Savings Time Canada and Continental US: • Begin DST at 2am on the second Sunday in March. • End DST at 2am on the first Sunday in November . Middle Europe and Portugal : • Begin DST at 2am the first Su nday on or afte r March 25th.
Daylight Savings Time on ProCurve Switches Configuring Daylight Savings Time Before configuring a "U ser defined" Daylight T ime Rule, it is importa nt to understand how the switch treats the en tries.
Daylight Savings Time on ProCurve Switches Configuring Daylight Savings Time E-4.
Index Symbols => prompt … C-45 Numerics 802.1x LLDP blocked … 13-35 802.1X effect, LLDP … 13-53 802.3u auto negotiation standard … 10-4 A access manager … 13-13 operator … 13-13 Actions.
comparing startu p to running … 6 -6 console … 7-3 copying … A-18 download … A-3 factory default … 6-9, 8-2 IP … 8-3 network monitoring … B-23 permanent … 6-7 permanent change defined .
Syslog logging disabled … C-27 Syslog server, view configuration … C-30 Syslog, number of servers … C-25 Telnet session … C-25 debug logging, LLDP … 13-33 default gateway … 8-3 default tru.
statistics … B-19 inactivity timeout … 7-4 Inbound Telnet Enabled par ameter … C-6 Inconsistent value … 13-40 inform requests … 13-22 invalid input … 4-13 IP CLI access … 8-7 configurati.
LLDP 802.1D-compliant switch … 13-53 802.1x blocking … 13-35 802.1X effect … 13-53 active port … 13-30 advertisement … 13-30 advertisement content … 13-43 advertisement data … 13-45 adve.
load balancing See port trunk. logical port … 12-7 loop, network … 12-3 lost password … 5-10 M MAC address … 8-14, B-6, D-2 duplicate … C-14, C-19 learned … B-12, B-13 listing connected de.
event log messages … 11-14 operation on ProCurve switches … 11-2 planning and implementation … 11-13 port priority … 11-5 power supplies … 11-3 pre standard detect … 11-10 pre-802.
power over ethernet See PoE. pre-standard detect … 11-10 ProCurve Networking support URL … 5-13 prompt, => … C- 45 public SNMP community … 13-5 publication data … 1-ii Q qos pass-through .
snmp-server inform … 13- 22 SNMPv3 "public" community access caution … 13-6 access … 13-5 assigning users to groups … 13-8 communities … 13-12 enable command … 13-7 enabling … .
t e r m i n a l t y p e…7 - 3 terminate remote session … 7-9 TFTP download … A-4 OS download … A-3 threshold setting … 13-5 thresholds, SNMP … 13-20 time format … C-21 time protocol sele.
V support … 5-12, 5-13 user name, usin g for browser o r console access … 5-8, 5-10 users, SN MPv3 See SNMPv3. using the passwords … 5-10 utilization, port … 5-15 version, OS … A-5, A-12, A-.
12 – Index.
.
© Copyright 200 7 Hewlett-Packar d Development Company , L.P . December 200 7 Manual Part Number 599 1-8640.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il HP ProCurve 2610-PWR è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del HP ProCurve 2610-PWR - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso HP ProCurve 2610-PWR imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul HP ProCurve 2610-PWR ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il HP ProCurve 2610-PWR, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del HP ProCurve 2610-PWR.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il HP ProCurve 2610-PWR. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo HP ProCurve 2610-PWR insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
