Manuale d’uso / di manutenzione del prodotto C100 del fabbricante HP
Vai alla pagina of 34
C100_110-160_180.FB -1 Tue Jul 16 06:36:50 1996 Installing the C100/C1 10 to C160/C180 CPU Upgrade HP Part No. A4200-90017 E0796 Printed in USA.
C100_110-160_180.FB 0 Tue Jul 16 06:36:50 1996 Hewlett-Packard Co. 1996 Printing History First Printing: July 1996 UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Limited. NOTICE The information contained in this document is subject to change without notice.
C100_110-160_180.FB 1 Tue Jul 16 06:36:50 1996 1 Upgrading your Model C100/1 10 to a Model C160 or C180 Upgrading your Model C100/110 to a Model C160 or C180 Y our upgrade kit contains a Main T ray Assembly , which, when installed, upgrades your Model C100/1 10 to a Model C160/C180.
C100_110-160_180.FB 2 Tue Jul 16 06:36:50 1996 2 Preparing Y our Workstation Preparing Your Workstation Before starting the upgrade, use the following procedure to prepare the workstation: 1 The workstation must be running HP-UX 10.20 or later to accommodate the C160/C180 upgrade.
C100_110-160_180.FB 3 Tue Jul 16 06:36:50 1996 3 Preparing Y our Workstation 4 Next, you need to run the upgrade utility program to automatically convert the hardware paths stored in the system’s I/O configuration file. You should only run this utility if you are going to complete the rest of the hardware upgrade described in this document.
C100_110-160_180.FB 4 Tue Jul 16 06:36:50 1996 4 Preparing Y our Workstation 5 If your system has an A4070B HCRX-8Z or an A4071B with the A4272A accel- erator graphics adapter installed enter the following commands to save the cur- rent versions of the /etc/ioconfig and /stand/ioconfig files: mv /etc/ioconfig /etc/ioconfig.
C100_110-160_180.FB 5 Tue Jul 16 06:36:50 1996 5 Preparing Y our Workstation 12 Unplug the power cord of the system unit, the monitor, and any peripheral devic- es from ac wall outlets.
C100_110-160_180.FB 6 Tue Jul 16 06:36:50 1996 6 Preparing Y our Workstation 14 Remove the floor stand from the system unit, as shown in Figure 1. Figure 1 Removing the Floor Stand 15 Lay the system unit on a flat surface, such as a table top. 16 Attach a static-grounding wrist strap to bare metal on the back of the system unit.
C100_110-160_180.FB 7 Tue Jul 16 06:36:50 1996 7 Removing the Main T ray Assembly Removing the Main Tray Assembly Once you have prepared the workstation, you need to remove the main tray from the system unit, as described in the following procedure: 1 Completely loosen the four thumb screws on the rear of the system unit, as shown in Figure 2.
C100_110-160_180.FB 8 Tue Jul 16 06:36:50 1996 8 Removing Memory Modules Removing Memory Modules After removing the main tray from the system, you must remove the mem- ory modules from the original C100/1 10 CPU board, as described in the fol- lowing procedure: 1 Locate the memory modules on the C100/C110 CPU board, as shown in Figure 3.
C100_110-160_180.FB 9 Tue Jul 16 06:36:50 1996 9 Removing Memory Modules 2 To remove a memory module, push the ejector tabs on each side of the module. Lift the memory module up and out of the connector and place it on a static-free surface. Figure 4 shows how to remove a memory module.
C100_110-160_180.FB 10 Tue Jul 16 06:36:50 1996 10 Removing Option Boards Removing Option Boards NOTICE: Any option boards that are supported by the new C160/180 system should be installed in the same slot number in the new main tray .
C100_110-160_180.FB 11 Tue Jul 16 06:36:50 1996 11 Removing Option Boards 2 Slide the EISA slider to the side to remove it, as shown in Figure 6. 3 Remove the screw from the EISA retainer, as shown in Figure 6 4 Grasp the option board by the edge with both hands and pull it straight out from its slot.
C100_110-160_180.FB 12 Tue Jul 16 06:36:50 1996 12 Installing Memory Modules Installing Memory Modules Install the memory modules in the C160/C180 CPU board in the new main tray , as described in the following procedure: 1 Locate the memory connectors on the C160/C180 CPU board, as shown in Figure 7.
C100_110-160_180.FB 13 Tue Jul 16 06:36:50 1996 13 Installing Memory Modules T able 1 Model C160/C180 Allowable Memory Configurations Config. No. Pair 0 Pair 1 Pair 2 Pair 3 Pair 4 Pair 5 T otal MB .
C100_110-160_180.FB 14 Tue Jul 16 06:36:50 1996 14 Installing Memory Modules 25 32 32 32 32 32 32 32 32 32 32 320 26 32 32 32 32 32 32 32 32 32 32 16 16 352 27 32 32 32 32 32 32 32 32 32 32 32 32 384 .
C100_110-160_180.FB 15 Tue Jul 16 06:36:50 1996 15 Installing Memory Modules 49 64 64 64 64 256 50 64 64 64 64 16 16 288 51 64 64 64 64 16 16 16 16 320 52 64 64 64 64 16 16 16 16 16 16 352 53 64 64 64.
C100_110-160_180.FB 16 Tue Jul 16 06:36:50 1996 16 Installing Memory Modules 73 64 64 64 64 64 64 32 32 32 32 32 32 576 74 64 64 64 64 64 64 64 64 512 75 64 64 64 64 64 64 64 64 16 16 544 76 64 64 64 .
C100_110-160_180.FB 17 Tue Jul 16 06:36:50 1996 17 Installing Memory Modules 2 To install a memory module, close the ejector tabs on each side of the memory connector and line the memory module up with the guides, as shown in Figure 8.
C100_110-160_180.FB 18 Tue Jul 16 06:36:50 1996 18 Installing Option Boards Installing Option Boards NOTICE: Any option boards that are supported by the new C160/180 system should be installed in the same slot number in the new main tray that they were installed in the old main tray .
C100_110-160_180.FB 19 Tue Jul 16 06:36:50 1996 19 Installing Option Boards Graphics Configuration Restrictions The system supports only four graphics displays at a time. A “display” is a video output port or connector . For example, the Dual V isualize Enhanced Graphics Card (A4451A) is a dual display card.
C100_110-160_180.FB 20 Tue Jul 16 06:36:50 1996 20 Installing Option Boards Option Board Installation If you removed option boards from the C100/1 10 main tray , use this proce- dure to install them in the new C160/C180 main tray . Otherwise, skip to the next section.
C100_110-160_180.FB 21 Tue Jul 16 06:36:50 1996 21 Installing Option Boards 2 Remove the screw from the EISA retainer, and remove the EISA retainer, as shown in Figure 10. Figure 10 Removing the EISA Retainer and EISA Slider 3 Remove the EISA slider, as shown in Figure 10.
C100_110-160_180.FB 22 Tue Jul 16 06:36:50 1996 22 Installing Option Boards 4 In the desired option slot, turn the blank plate’s locking knob counter-clockwise to unlock the plate, as shown in Figure 11. NOTE: The new main tray assembly contains a blank plate which is held in by a locking knob.
C100_110-160_180.FB 23 Tue Jul 16 06:36:50 1996 23 Installing Option Boards 6 Slide the option board into the slot. Make sure that the hole in the board’s handle aligns with the pin on the back panel, as shown in Figure 12.
C100_110-160_180.FB 24 Tue Jul 16 06:36:50 1996 24 Installing Option Boards 8 Replace the EISA retainer and its screw, as shown in Figure 13. 9 Replace the EISA slider, as shown in Figure 13 Figure 13.
C100_110-160_180.FB 25 Tue Jul 16 06:36:50 1996 25 Installing Option Boards 10 Rotate the fan back into place and firmly push it into the rear panel firmly until the clip snaps into place, as shown in Figure 14.
C100_110-160_180.FB 26 Tue Jul 16 06:36:50 1996 26 Installing the New Main T ray Assembly Installing the New Main Tray Assembly Install the new C160/C180 main tray assembly , as described in the following procedure: 1 Align the main tray assembly with the chassis and slide it into place, as shown in Figure 15.
C100_110-160_180.FB 27 Tue Jul 16 06:36:50 1996 27 Installing the New Main T ray Assembly 5 Remove any external SCSI terminators from the rear of the old main tray and in- stall them on the SCSI connectors on the rear of the system. 6 Use a small flat blade screwdriver to gently pry the old model number label from the front of the system.
C100_110-160_180.FB 28 Tue Jul 16 06:36:50 1996 28 Installing the New Main T ray Assembly 7 Replace the system unit in the floor stand, as shown in Figure 17.
C100_110-160_180.FB 29 Tue Jul 16 06:36:50 1996 29 Installing the New Main T ray Assembly 8 Reconnect the power cables and any other cables that you disconnected when opening the workstation.
C100_110-160_180.FB 30 Tue Jul 16 06:36:50 1996 30 Installing the New Main T ray Assembly 11 The system cycles through all of the available monitor types one at a time. When you can see a message similar to the following clearly and litigable, select that monitor type by pressing Enter.
C100_110-160_180.FB 31 Tue Jul 16 06:36:50 1996 31 Installing the New Main T ray Assembly 15 At the prompt, enter the following command to enter the configuration menu: co 16 Configure the console path for the built-in graphics with the following syntax: mo graphics(0) 17 Power off the system.
C100_110-160_180.FB 32 Tue Jul 16 06:36:50 1996 32 Installing the New Main T ray Assembly.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il HP C100 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del HP C100 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso HP C100 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul HP C100 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il HP C100, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del HP C100.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il HP C100. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo HP C100 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
