Manuale d’uso / di manutenzione del prodotto FSPCI64S del fabbricante HP (Hewlett-Packard)
Vai alla pagina of 20
FuturePlus Systems Corporation LOCAL BUS PCI Scope Preprocessor Users Manual-FSPCI64S For Hewlett-Packard Logic Analysis Systems Revision 1.0 FuturePlus Systems and PCI Scope is a trademark of FutureP.
2 HOW TO REACH US 4 PRODUCT WARRANTY 5 Limitation of warranty 5 Exclusive Remedies 5 Assistance 6 INTRODUCTION 7 How to Use This Manual 7 ANALYZING THE PCI LOCAL BUS 8 Duplicating the Master Diskette .
3 Standards Supported 15 Power Requirements 15 MultiProbe Pods required 15 Signal loading 15 Operations 16 Environmental Temperature 16 Altitude 16 Humidity 16 Testing and Troubleshooting 16 Servicing.
4 How to reach us FuturePlus Systems can be reached at: FuturePlus Systems Corporation 36 Olde English Road Bedford, NH 03110 TEL:603-471-2734 FAX:603-471-2738 Internet: 71035.3052@compuserve.com WEB:www.futureplus.com FuturePlus Systems is represented in Japan by: ANDOR Systems Support Co.
5 Product Warrant y This FuturePlus Systems product has a warranty against defects in material and workmanship for a period of 1 year from the date of shipment. During the warranty period, FuturePlus Systems will, at its option, either replace or repair products proven to be defective.
6 SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON CONTRACT, TORT, OR ANY OTHER LEGAL THEORY. Product maintenance agreements and other customer assistance agreements are available for FuturePlus Systems products.
7 Introduction The PCI Scope Preprocessor module provides a complete interface between any PCI add-in slot and the HP MultiProbe system. The Preprocessor interface connects the signals from the PCI Local bus to the inputs of a 208 PQFP package used as the MultiProbe connection point.
8 Analyzing the PCI Local Bus This chapter introduces you to the PCI Scope Preprocessor and lists the minimum equipment required and accessories supplied for PCI Local Bus analysis. Before you use the PCI Preprocessor software, make a duplicate copy of the master diskette.
9 • An Oscilloscope • The PCI Scope Preprocessor Product • A PCI target bus This operating manual uses the same signal notation as the PCI LOCAL BUS SPECIFICATION - REVISION 2.1. That is, a # symbol at the end of a signal name indicates that the signal’s active state occurs when it is at a low voltage.
10 PCI_MUL.DUT and PCI.ADP from your PCI Scope Preprocessor diskette to that directory. 3. Access the configuration menu of the MultiProbe Control card. 4. Select POD setup for the POD that will be connected to the Scope Preprocessor. 5. On the next menu select #2 Specify POD adapter and then select the file PCI.
11 Analog Analysis Since the PCI Scope Preprocessor interface contains only passive matching terminators it introduces negligible skew to the PCI Local Bus signals. The following procedure describes the major steps required to perform analog analysis measurements with the PCI Scope Preprocessor module.
12 Select the oscilloscope for each MultiProbe output using the Select Signals menu of the MultiProbe control module. 1. Access the Select Signals menu. 2. Select the scope for each output a) Choose the output (Output 1 or Output 2) of the control module that is connected to the pod that is attached to the PCI Scope Preprocessor.
13 Using an HP16534A oscilloscope If you are using an HP 16534A oscilloscope, then follow this procedure. 1. Access the oscilloscope menus. To view your measurements with an HP16534A oscilloscope, you need to exit the MultiProbe Control menus, then enter the oscilloscope menus.
14 When the PCI Personality Adapter 101 is not in use, keep it in its original container. The file PCI.ADP matches the configuration of the PCI Personality Adapter and configures the MultiProbe for PCI Analysis.
15 General Information This chapter provides additional reference information including the characteristics and signal connections for the PCI Scope Preprocessor module. The following operating characteristics are not specifications, but are typical operating characteristics for the PCI Scope Preprocessor module.
16 information on the electrical loading of the MultiProbe Pod refer to your Hewlett-Packard MultiProbe specification. All PCI Local Bus operations supported.
17 The below table shows the connection from the PCI Local Bus to the PQFP package that acts as the MultiProbe Contact point. If the pin is not listed it is Grounded.
18 AD26 75 AD25 77 AD24 79 C/BE3# 81 AD23 83 AD22 85 AD21 87 AD20 89 AD19 91 AD18 93 AD17 95 AD16 97 C/BE2# 99 FRAME# 101 IRDY# 103 TRDY# 105 DEVSEL# 107 STOP# 109 LOCK# 111 SDONE 113 PERR# 115 SBO# 1.
19 AD09 137 C/BE0# 139 AD08 141 AD07 143 AD06 145 AD05 147 AD04 149 AD03 151 AD02 153 AD01 155 AD00 157 ACK64# 159 REQ64# 161 C/BE7# 163 C/BE6# 165 C/BE5# 167 C/BE4# 169 PAR64 171 AD32 173 AD33 175 AD.
20 AD45 199 AD46 201 AD47 203 AD48 205 AD49 207.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il HP (Hewlett-Packard) FSPCI64S è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del HP (Hewlett-Packard) FSPCI64S - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso HP (Hewlett-Packard) FSPCI64S imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul HP (Hewlett-Packard) FSPCI64S ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il HP (Hewlett-Packard) FSPCI64S, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del HP (Hewlett-Packard) FSPCI64S.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il HP (Hewlett-Packard) FSPCI64S. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo HP (Hewlett-Packard) FSPCI64S insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
