Manuale d’uso / di manutenzione del prodotto D3K19UT#ABA del fabbricante HP (Hewlett-Packard)
Vai alla pagina of 160
Maintenance and Service Guide HP Compaq Pro 4300 Small Form Factor Business PC.
© Copyright 2012 Hew lett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft and Windows are trademarks of Microsoft Corporation in the U.
About This Book WARNING! Text set off in this manner indi cates that failure to follow di rections could result in bodily harm or l oss of life . CAUTION: Text set off in this manner indicates that failure to follo w directions could result in damage to eq uipment or loss of informa tion.
iv About This Book.
Table of contents 1 Produc t Feature s ............ ............ .............. ........... ............... ............ ............... ........... ..... ............ ........... .......... 1 Standar d Configu ration Fe atures ........... ...........
5 Identifying the Ch assis, Routine Care , and Disassembly Preparation ..... .......... ....... ........... ........ ........... 19 Chassis Designations .............. .......... ......... ............. .......... ......... ............. .......... ..
Installing DIMMs ..... ............................................. ............... ............. ............ .......... .......... .. 44 Removi ng or Installing an E xpansi on Card ............ ............... ................. ................. ..
Before You Call f or Technic al Sup port ......... ............. ........... ............ ........... ............ ........... .......... ...... 96 Helpful Hints ...... ......... ........ ............ ........ ......... ........ ........... ......... .
1 Product Features Standard Configuration Features The HP Compaq Small Form Factor features ma y vary depending on the model. For a comp lete listing of the hardware and softwar e installed in the computer, run the diagnostic utility (included on some computer models on ly).
Front Panel Components Drive configuration ma y vary by model. Some models have a b ezel blank covering one or more drive bays. Figure 1 -2 Front Panel Componen ts Table 1-1 Fron t Panel Compon ents 1 5.25-inch Optical Drive 6 USB (U niversal Serial Bus) Ports 2 Optical Drive Activity Light 7 Microphone Connector 3 Optical Drive Eject Button 8 3.
Rear Panel Components Figure 1 -3 Rear Panel Components Table 1-2 Rear Panel Comp onents 1 RJ-45 Network Connector 6 DVI-D Connector 2 VGA Monitor Connector 7 PS/2 Mouse Connector (green) 3 Serial Con.
Serial Number Location Each computer has a un ique serial number and product ID number in the loca tion shown below. Keep these numbers available for use when co ntacting customer service for assistance .
2 Installing and Customizing the Software If your computer was not shipped with a Micros oft operating s ystem, some port ions of this documentation do not ap ply. Additional information is availa ble in online help a fter you install the operating system.
3. Select the All Programs menu. 4. Click on the Windows Update link. In Windows Vista an d Windows 7, the Windows Update screen appears. Click vie w available updates and make sure all critical update s are selected. Click th e Install button and follow the instructions on the scree n.
Accessing Disk Image (ISO) Files There are disk image files (ISO files) included on your PC that contain the installation software for additional software . These CD image files are l ocate d in the folder C:SWS etupISOs. E ach .iso file can be burned to CD media to create an installation CD.
3 Computer Setup (F10) Utility Computer Setup (F10) Utilities Use Computer Setup (F10) Utility to do the following: ● Change factory default settings. ● Set the system date and time. ● Set, view, change, or verify the system configurat ion, including settings for processor, graphics, memory, audio, stora ge, communications, and input devices.
Using Computer Setup (F10) Utilities Computer Setup ca n be accessed only by tu rning the compu ter on or restar ting the system. To access the Computer Setup Utilities menu , complete the following steps: 1.
Computer Setup—File NOTE: Support for specific Computer Setup op ti ons may vary depend ing on the hardware configuration. Table 3-1 Computer Setup— File Option Description System Information List.
Computer Setup—Storage NOTE: Support for specific Computer Setup op ti ons may vary depend ing on the hardware configuration. Table 3-2 Computer Setup—Storage Option Description Device Configuration Lists all installed BIOS-controlled storage devices.
Computer Setup—Security NOTE: Support for specific Computer Setup op ti ons may vary depend ing on the hardware configuration. Table 3-3 Com puter Setup—Securi ty Option Description Setup Password Allows you to set and enable a setup (a dministrator) password.
Table 3-3 Com puter Setup—Securi ty (continued) System IDs Displays the following: ● Product name ● Serial number ● Universal Unique Identifier (U UID) number. The UUID can only be updated if the curr ent chassis serial number is invalid. (These ID numbers are normally set in th e factory and are used to uniquely ide ntify the system.
Computer Setup—Power NOTE: Support for specific Computer Setup op ti ons may vary depend ing on the hardware configuration. Table 3-4 Computer Setup—Power Option Description Hardware Power Management ● SATA Power Management—Enables or disabl es the SATA bus and/or device power management.
Computer Setup—Advanced NOTE: Support for specific Computer Setup op ti ons may vary depend ing on the hardware configuration. Table 3-5 Com puter Setup—Ad vanced Option Heading Power-On Options Allows you to set: ● POST messages (enable/disable).
Table 3-5 Com puter Setup—Adva nced (continued) Bus Opti ons On some models, allows you to enable or disable: ● PCI SERR# Generation. Default is enable. ● PCI VGA Palette Snooping, which sets the VG A palette snooping bit in PCI configuration space; only needed when more than one graphics cont roller is installe d.
4 Serial ATA (SATA) Drive Guidelines and Features NOTE: HP only supports the use of SATA hard driv es on these models of computer. No Parallel ATA (PATA) drives are supported. SATA Hard Drives Serial ATA Hard Drive Characteristics Number of pins/conductors in data cable 7/7 Number of pins in power cable 15 Maximum data cable length 39.
SMART ATA Drives The Self Monitoring Analysis an d Recording Tec hno logy (SMART) ATA drives for the HP Personal Computers have built-in drive failure p rediction that warn s the user or netw or k administrator of an impending failure or crash of the hard drive.
5 Identifying the Chassis, Routine Care, and Disassembly Preparation This chapter provides general service information for the computer. Ad herence to th e procedures and precautions described in this chapter is esse ntial for proper service.
Electrostatic Discharge Information A sudden discharge of static electricity f rom your fi nger or other conductor ca n destroy static-sensitive devices or microcircuitry.
● Always be properly ground ed when touching a sen sitive component o r assembly. ● Avoid contact with pins, lea ds, or circuitry. ● Place reusable electrostatic- sensitive parts fro m assemblie s in protective p ackaging or conductive foam.
● Conductive bi ns and other as sembly or soldering ai ds ● Conductive foam ● Conductive tabletop workstations with ground cord of one-meg ohm +/- 10% resistance ● Static-di ssipativ e table o.
● Never cover the vent ilation slots on th e monitor with any type of material. ● Install or enable power managemen t functions of the operating system or other software, including sleep s tates. Routine Care General Cleaning Safety Precautions 1.
CAUTION: Use safety glasses equipped with side sh ields before attempti ng to clean debris from under the keys. ● Visible debris undern eath or between th e ke ys may b e removed by vacuuming or shakin g. ● Canned, pressuri zed air may be used to clean debri s from under the keys.
Tools and Software Requirements To service the co mputer, you need the fo llowing: ● Torx T-15 screwdriver (HP screwd river with b its, PN 161946-0 01) ● Torx T-15 screwdriver with small diameter .
● Before handling a drive, ensure th at you are di scharged of static electricity. While hand ling a drive, avoid touching the connector. F or more information about pre venting electrosta tic damage, refer to Electrostati c Discharge Information on page 20 ● Do not use exc essive force when inse rting a drive.
6 Illustrated parts catalog This chapter provides parts information for the chassis. Spare parts Computer major components Spare parts 27.
Item Description Spare part number (1) Access panel 636924-001 (2) Front bezel 636920-001 (3) Power supply 240W, 85% efficiency 613663-001 240W, high voltage protection 613664-001 240W 613763-001 (4) .
Item Description Spare part number Optical d rives 6X BD-Writer SuperMulti drive 656792-001 16X DVD±RW SuperMulti drive 660408-001 16X DVD-ROM drive 682550-001 Expansion cards ATI Radeon HD7450, 1-GB.
Item Description Spare part number ● Intel Celeron G550 processor, 2.6 GHz 691934-001 ● Intel Celeron G540 processor, 2.5 GHz 665119-001 ● Intel Celeron G460 processor, 1.
Spare part number Description 537745-031 Keyboard, PS/2, the United Kingdom 537745-041 Keyboard, PS/2, Germany 537745-051 Keyboard, PS/2, France 537745-061 Keyboard, PS/2, Italy 537745-071 Keyboard, P.
Spare part number Description 537745-CA1 Keyboard, PS/2, Estonia 537745-DD1 Keyboard, PS/2, Iceland 537745-DE1 Keyboard, PS/2, Arab 537745-DF1 Keyboard, PS/2, Kazakstan 537745-KD1 Keyboard, PS/2, Sout.
Spare part number Description 537746-AB1 Keyboard, USB, Taiwan 537746-AC2 Keyboard, USB, Hong Kong 537746-B31 Keyboard, USB, International English 537746-BB1 Keyboard, USB, Israel 537746-BL1 Keyboard,.
Spare part number Description 631411-114 Keyboard, USB, SmartCard, Switzerland 631411-124 Keyboard, USB, SmartCard, French Canada 631411-134 Keyboard, USB, SmartCard, Portugal 631411-144 Keyboard, USB.
Spare part number Description 636919-001 Heat sink (includes replacement thermal material) 636920-001 Front bezel 636921-001 Baffle 636922-001 Chassis fan 636923-001 SATA power cable 636924-001 Access.
Spare part number Description 682411-001 ATI Radeon HD7450 PCIe x16 graphics car d, 1 GB (includes adapter) 695080-001 Front bezel 674314-121 Keyboard, wireless, for use in French Canada 674317-001 Mo.
7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis Adherence to the p rocedures and pr ecautions de scribed in this chapt er is essential fo r proper servic e. After completing all necessary removal and replacemen t procedures, run the Diagnostics utility to verify that all compo nents operate properly.
3. Exit the operating system. 4. Remove any compact disc or me dia card from the computer. 5. Turn off the compu ter and any peripheral devices that are connected to it.
Computer Access Panel Description Spare part num ber Access panel 636924-00 1 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 37 ). 2. If the computer is o n a stand, re move the computer from the stand. 3. Loosen the captive thumbscrew (1) , then lift the access panel off the computer (2) .
Front Bezel Description Spare part num ber Front bezel 695080-001 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 37 ). 2. Remove the access pan el ( Computer Access Pane l on page 39 ). 3. Lift up the three tabs on the side of the bezel (1) , then rotate the bezel off the chassis (2) .
Bezel Blanks Description Spare part num ber 5.25-inch bezel blank 570838-001 On some models, there are bezel blanks covering the 3.5-inch and 5.25-inch extern al drive bays that need to be removed befo re installing a drive. To remove a bezel blank: 1.
System Board Connections Refer to the following illustration and tabl e to identify the sys tem board connectors. Figure 7 -5 System Board Connections Table 7-1 System Board Conne ctions No.
Installing Additional Memory Description Spare part num ber 8-GB, PC3-12800 689375-001 4-GB, PC3-12800 671613-001 2-GB, PC3-12800 671612-001 The computer comes with double data rate 3 syn chrono us dynamic random access memory (DDR3- SDRAM) dual inline memo ry modules (DIMMs).
Populating DIMM Sockets There are two DIMM sockets on the system board: XMM1 and XMM3 with one socket per Channel. XMM3 operates in memory cha nnel A. XMM1 operates in memory Channel B. The system will au tomatically operate i n single channel mode, d ual channel mode, or flex mode, depending on how the DIMMs are i nstalled.
3. Rotate up the drive bay housing to access the memory mod ule sockets on the system board. Figure 7-6 Rotating the Drive Cage Up 4. Open both latches of the memory module socket (1) , and insert the memory modul e into the socket (2) . Figure 7-7 Installing a DIMM NOTE: A memory module can be installed in on ly one way.
6. Rotate the drive ca ge back down to its normal po sition. Figure 7-8 Rotating the Drive Cage Down 7. Replace the access pane l. 8. If the computer was on a stand, repl ace the stand. 9. Reconnect the p ower cord and turn on the co mputer. 10. Lock any security devices that we re disengaged when the access pan el was remove d.
NOTE: The PCI and PCI Express slots support o nly low profile cards. NOTE: You can install a PC I Express x1, x4, x8 , or x16 expans ion card in the PCI Exp ress x16 slot. To install an expansion card: 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 37 ).
5. Before installing an expansion ca rd, remove the expansion slot co ver or the existing expansion card. a. If you are installing an expan sion card i n a vacant socke t, remove the appropriate expansion slot cover o n the back of the chassis. Pul l the slot cover straight up then a way from the inside of the cha ssis.
b. If you are removing a standard PCI card or PC I Express x1 card, hold the card at each end, and carefully rock it back a nd forth until th e connectors pull fre e from the socket. Pull the expansion card straigh t up from the socket (1) then away from the in side of the chassis to release it from the chassis frame (2) .
c. If you are removing a PCI Express x16 card, pull the rete ntion arm on the back of the expansion socke t away from the card and ca refully rock the card back and forth until the connectors pull free from the socket.
8. To install a new expansio n card, hold the card just above the expans ion socket on the system board then move the card toward the rear of the chassis (1) so that the bracket on the card is aligned with th e open slot on the rear of the chassis. Press the card straight down into the expansion socket on the system board (2) .
13. Reconnect the power cord an d turn on the compute r. 14. Lock any security devices that we re disengaged when the access pan el was remove d. 15. Reconfigure the computer, if ne cessary.
Cable Management The Small Form Factor chassis is a very compact co mputer and prope r routing of the inte rnal cables is critical to the operation of the computer. Fo llow good cable mana gement practice s when working inside the computer. ● Keep cables away from major heat sources like the h eat sink.
Drives Description Spare part num ber Optical drives: 6X BD-Writer SuperMulti drive 65679 2-001 16X DVD±RW SuperMulti drive 660408-001 16X DVD-ROM drive 682550-001 Hard drives: 1 TB hard drive 636930-001 500 GB hard drive 636929-001 250 GB hard drive 636927-001 256 GB Solid-state drive (SSD), SATA 6.
Drive Positions Figure 7 -15 Drive Positions Table 7-2 Drive Positions 1 3.5-inch internal hard drive bay 2 3.5-inch internal drive bay for opti onal drives (media car d reader shown) 3 5.
NOTE: If you are replacing th e primary hard drive, you must remove the fo ur silver and blue 6-32 isolation mounting screws from the old hard dr ive and install them i n the new hard drive. Figure 7 -16 Extra Mounting Screw Locatio ns Table 7-3 Extra Mounting Screws No.
Removing an Internal 5.25-inch Drive CAUTION: All removable media should be taken out of a drive before removin g the drive from the computer. To remove a 5.25-inch interna l drive: 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 37 ).
5. Rotate the drive ca ge back down to its normal po sition. CAUTION: Be careful not to pin ch any cables or wire s when rota ting the drive cage d own. Figure 7-19 Ro tating th e Drive Ca ge Down 6. Slide the drive back until it stops, then lift it up a nd out of the drive cage.
Installing an Optical Drive in to the 5.25-in ch Drive Bay To install an optional 5.25-inch optical d rive: 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 37 ). 2. Remove the access pan el ( Computer Access Pane l on page 39 ).
6. Rotate the drive ca ge to its upright p osition (1) and install an M3 mounting screw in the back left side of the drive (2) to secure the drive to the drive ca ge. Figure 7-23 Securing the Drive in the Drive Cage 7. Connect the SATA da ta cable to the white system board connector lab eled SATA1 if it is not already connected.
10. Rotate the drive cage back down to its normal position. CAUTION: Be careful not to pinch a ny cables or wires when rotati ng the drive cag e down. Figure 7-25 Ro tating th e Drive Ca ge Down 11. Replace the access panel. 12. If the computer wa s on a stand, replace th e stand.
2. If you are remo ving a media card rea der, di sconnect the USB cable from the system board. Figure 7-26 Disconnecting the Media Card Reader USB Cab le 3. Rotate the drive ca ge to its upright p osition (1) and remove the mountin g screw on the back left side of the drive (2).
5. Slide the drive back until it stops, then lift it up a nd out of the drive cage. Figure 7-29 Removin g a 3.5-inch Drive (Media Card Reader Shown) NOTE: When repla cing a 3.5-inch drive, tran sfer the four mounting screws from th e old drive to the new one.
4. Position the mounting scre ws on the drive into the J-slots in the drive bay. Then slide the drive toward the front o f the computer until it stops.
7. If installing a media card reader, connect the USB cable from the media card reader to the USB connector on the system board labeled MEDIA1. Figure 7-34 Co nnecting the Media Card Rea der USB Cable NOTE: Refer to System Board Connections on page 42 for an illustration of the system board drive connectors.
Removing and Replacing th e Primary 3. 5-inch Internal SATA Hard Drive NOTE: Before you remove th e old hard drive, be sure to back up the data from the o ld hard drive so that you can transfer the data to the new hard drive. The preinstalled 3.5-inch hard drive is located under the power supply.
5. Press and hold down the latch to disconnect the power cable (1) and d ata cable (2) from the back of the hard drive. Figure 7-37 Disconne cting the Hard Drive Power Cable and Data Cable 6. Press down on the green release l atch next to the hard drive (1) .
8. Align the mounting screw s with the slots on th e chassis drive cage, pr ess the hard drive down into the bay, then slide it back until it stops and locks in place. Figure 7-40 Installing the Hard Drive 9. Connect the p ower and data cables to the back of the hard drive.
Baffle Description Spare part num ber Baffle 636921-001 The baffle sits be tween the front fan and the h eat sink. 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 37 ). 2. Remove the access pan el ( Computer Access Pane l on page 39 ).
Front Fan Assembly Description Spare part num ber Front fan assembly 636922-001 The front fan assemb ly is attach ed to the fron t of the chassis. 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 37 ). 2. Remove the access pan el ( Computer Access Pane l on page 39 ).
Front I/O, Power Switch Assembly Description Spare part num ber Front I/O and power switch assembly 636926-001 The front I/O an d power switch/LEDs are one a ssembly, attached to the front of the chass is. Push the assembly into the ch assis to remove.
8. Route the cables through the slots beneath the driv e cage , pull the assembly (rig ht side first) into the chassis, and then remove th e assembly from the computer. Figure 7-45 Routing the cables and re moving the power switch a ssembly To install the front I/O an d power switch assembly, reverse the removal proced ure.
7. Lift the speaker from the inside of the chassis to remove it (2) . Figure 7-46 Removing the speaker To install the speaker, reverse the removal procedures. Heat sink Description Spare part num ber Heat sink 636919-001 The heat sink is secured atop the processor with four cap tive Torx screws.
5. Loosen the four captive screws that secure the h eat sink to the system board tray. CAUTION: Heat sink retaining screws shou ld be removed in di agonally opposite pairs (as in an X) to even the downward forces on the processo r.
6. Lift the heat sink fro m atop the processor and set i t on its side to keep from co ntaminating the work area with thermal grease . Figure 7-48 Removing the heat sink When reinstalling the heat sink, ma ke sure that i ts bottom has been cleaned with an alcohol wipe and fresh thermal grease has been app lied to the top of the proce ssor.
Processor Description Spare part num ber Intel Core i7 3770s processor, 3.1 GHz 689370-001 Intel Core i5 3570 processor, 3.4 GHz 688162-001 Intel Core i5 3570s processor, 3.1 GHz 695079-001 Intel Core i5 3475s processor, 2.9 GHz 695078-001 Intel Core i5 3470s processor, 2.
7. Carefully lif t the proce ssor from the socket (3) . CAUTION: Do NO T handle the pins in the processor socket. These pins are very fragile a nd handling them co uld cause irreparable damage. Once pins a re damaged it ma y be necessary to replace the system bo ard.
6. If using a new heat sink, remo ve the protective covering from the bo ttom of the heat sink and place it in position atop the processor. 7. Secure the heat sink to the system board and system board tray with the four captive screws and attach the heat sink cont rol cable to the system board.
7. Pull the power supply forward (1) until the posts (2) on the power supply move forward in the power supply bracket, and then li ft the power supply straight up and ou t of the chassis. Figure 7-50 Removing the power supply Use the following table to determine the co rrect power supply/system board connections.
System Board Description Spare part num ber System board – standard (includes thermal ma terial) 676358-001 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 37 ). 2. Remove the access pan el ( Computer Access Pane l on page 39 ).
11. Slide the system board toward th e front of the chassis (2) , and then lift the rear of the system board up and ou t of the chassis (3) . Figure 7-51 Removing the system board To install the system board, reverse the removal procedure. NOTE: When replacing the system board, you must also c hange the ch assis serial number in the BIOS.
Battery The battery that comes with your comp uter provides power to the real-time clock and has a lifetime of about three ye ars. When replacin g the battery, use a battery equivalent to the battery originally installed on the comp uter. The computer come s with a 3-volt lithium coin cell battery.
Type 1 Battery Holder 1. Lift the battery out of its ho lder. Figure 7-52 Re moving the battery from a type 1 h older 2. Slide the replacemen t battery into position, positive side up. 3. The battery ho lder automatically se cures the batte ry in the proper position.
3. Replace the computer access p anel. 4. Plug in the comput er and turn on power to the computer. 5. Reset the d ate and time, your passwords, and any special system setups, using Computer Setup. Refer to Computer Setup (F10) Utility on page 8 . Type 3 Battery Holder 1.
Using the Small Form Fact or Computer in a Tower Orientation The Small Form Fa ctor computer can be used in a towe r orientation. T he HP logo plate o n the front bezel is adjustable for either desktop or tower orientation. 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 37 ).
Installing a Security Lock The security locks displayed below and on the follo wing pages can be used to secure the computer. HP/Kensington MicroSaver Security Cable Lock Figure 7 -56 Installing a Cab.
Padlock Figure 7 -57 Installing a Padlock Installing a Security Lock 87.
Front Bezel Security The front bezel can be lock ed in place by installing a security screw provided by HP. To install the security screw: 1. Remove/disengage an y security devices that prohibit opening the computer. 2. Remove all removable m edia, such as compact discs o r USB flash drives, from the computer.
9. Install the security screw next to the midd le front bezel release tab to secure th e front bezel in place. Figure 7-59 Installing the Front Bezel Securi ty Screw 10. Replace the access panel. 11. If the computer wa s on a stand, replace th e stand.
A Power Cord Set Requirements The power supplies o n some computers have exte rnal power switches. The voltage select switch feature on the co mputer permits it to operate from any line voltage between 100-120 or 220-240 volts AC.
Country-Specific Requirements Additional requi rements specific to a country are sh own in parentheses an d explained below. Country Accrediting Agency Country Accrediting Agency Australia (1) Austria.
B POST Error Messages This appendix lists the erro r codes, error messa g es, and the various indicator li ght and audible sequences that yo u may encounter durin g Power-On Self-Tes t (POST) or computer restart, the probable source of the problem, and steps you can take to resolve the error co ndition.
POST Numeric Codes and Text Messages This section covers those POST errors that have numeric codes associated with them. The section also includes some text messages th at may be encoun tered during POST. NOTE: The computer will beep once after a POST text message is disp layed on the screen.
Interpreting POST Diagnos tic Front Panel LEDs and Audible Codes This section covers the front panel LED co des as well as the audible codes that may o ccur before or during POST that do not necessarily have an error code or text message associ ated with them.
Table B -2 Diagnostic Front Panel LEDs and Audible Codes (co ntinued) Activity Blinks Possible Cause Recommended Action Red Power LED flashes four times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved.
C Troubleshooting Without Diagnostics This chapter provide s information on how to i denti fy and correct minor problems, such as diskette drive, hard drive, optical drive, gra phics, audio, memory, and software problems.
● Boot the computer to the Safe Mode to see if it wil l boot withou t all of the drivers loaded. When booting the o perating system, use “La st Known Configuration.” ● Refer to the comprehensive online tech nical support at http://www.hp.com/ support .
● Press and hold any key. If the system be eps, then the keyboard should be operating correc tly. ● Check all cable connections for lo ose connections or inco rrect connections. ● Wake the computer by pressing an y key on the keybo ard or pressing the power button .
Solving General Problems You may be able to easily resolve the g eneral pr obl ems described in this section . If a problem persists and you are unable to resolv e it yourself or if you fe el uncomfortable ab out performing the operation, contact an authorized dealer or reseller.
There is no sound or sound volume is t oo low. Cause Solution System volume may be set low or muted. 1. Check the F10 BIOS settings to make sure the internal system speaker is not muted (this setting doe s not affect the external speakers).
Table C -1 Solving General Pro blems (continued ) Poor performance is experienced. Cause Solution Too many applications running. 1. Close unnecessary applications to free up memory. 2. Add more memory. Some applications run in the background and can be closed by right-clicking on the ir corresponding icons in the task tra y.
System does not power on an d the LEDs on the front of the computer are not flashing. Cause Solution System unable to power on. Press and hold the power button for less than 4 seconds.
Solving Power Problems Common causes and so lutions for po wer problems are listed in the f ollowing table. Table C -2 Solving Power Problems Power supply shuts down intermittent ly. Cause Solution Voltage selector switch on rear of computer chassis (some models) not switched to correct line voltage (1 15V or 230V).
Power LED flashes Re d four times, onc e every second, follow ed by a two sec ond pause, and the co mputer beeps four times. (Beeps stop after fifth it eration but LEDs co ntinue flashing.) Cause Solution Power failure (power supply is overload ed). 1.
Solving Hard Drive Problems Table C -3 Solving Hard Drive Problems Hard drive error occurs. Cause Solution Hard disk has bad sectors or has failed. 1. In Microsoft Windows XP, right-click Start , click Explore , and select a drive. Select File > Properties > Tools .
Nonsystem disk/NTLDR missing message. Cause Solution The system is trying to start from a diskette that is not bootable. Remove the diskette from the diskette drive. The system is trying to start from the hard drive but the ha rd drive may have been damaged.
Computer seems to be loc ked up. Cause Solution Program in use has stopped responding to comma nds. Atte mpt the normal Windows “Shu t Down” procedure. If this fails, press the power button for four or more seconds to turn off the power. To restart the compu ter, press the power button again.
Solving Media Card Reader Problems Table C -4 Solvi ng Media Ca rd Reader Pr oblems Media card will not work in a digital camer a after formatting it in Microsoft Windows. Cause Solution By default, Windows will format any media card with a capacity greater than 32MB with the FAT3 2 format.
Do not know how t o remove a media card correctly. Cause Solution The computer’s software is used to safely eject the card. Open My Computer (Windows XP), Computer (Windows Vista), or Devices and Printers (Windows 7), r ight-click on the corresponding drive icon, and select Eject .
Solving Display Problems If you encounte r display problems, see the do cumentation that came with the monitor a nd to the common causes and solutions listed in the following table. Table C -5 Solving Display Problem s Blank screen (no video ). Cause Solution Monitor is not turned on and the monitor light is not on.
Cannot enable integr ated graphics after insta lling a PCI Express graphics card. Cause Solution On systems with Intel integrated graphics, the integrated graphics cannot be enabled after installing a PCI Express x16.
Dim characters. Cause Solution The brightness and contrast controls are not set pr operly . Adjust the monitor brightne ss and contrast controls. Cables are not properly co nnected. Check that the graphics cable is securely connecte d to the graphics card and the monitor.
“Out of Range” displays on screen. Cause Solution Video resolution and refr esh rate are set higher than wha t the monitor supports. Restart the computer and enter Safe Mode. Change the settings to a supported setting then restart the computer so that the new settings take effect.
Certain typed symb ols do not appear correct. Cause Solution The font you are using does not suppo rt that particular symbol. Use the Character Map to locate and select the appr opriate symbol. Click Start > All Programs > Accessories > System Tools > Character Map .
Solving Audio Problems If the computer ha s audio features a nd you enco unter audio problems, see the common cau ses and solutions listed in the foll owing table. Table C -6 Solving Audio Problems Sound cuts in and o ut. Cause Solution Processor resources are being used by other open applications.
Table C -6 Solving Audio Problems (continued) Sound does not come out of the speaker o r headphones. Cause Solution Computer is in standby mode. Press the power button to resume fro m standby mode. CAUTION: When attempting to resu me from standby mode, do not hold down the power button for more than four seconds.
There is no sound or sound volume is t oo low. Cause Solution The application is set to use a different audio device than speakers. Some graphics cards support audio over the DisplayPort connection, so multiple audio devices may be listed in Device Manager.
Table C -7 Solvin g Print er Problems (continue d) Printer prints garbled information. Cause Solution The cables may not be connected p roperly. Reconnect all cables. Printer memory may be overloaded. Reset the printer by turning it off for one minute, then turn it back on.
Solving Keyboard and Mouse Problems If you encounte r keyboard or mouse problems, see the document ation that came with the equipmen t and to the commo n causes and solutio ns listed in the following tabl e. Table C -8 Solving Keyboard Problems Keyboard commands and typing are not re cognized by the computer.
Table C -9 Solving Mouse Problems (continue d) Mouse does not respond to movement or is too slow. Cause Solution Program in use has stopped responding to comma nds. Shut dow n the computer using the keyboard then restart the computer. Mouse may need cleaning.
Solving Hardware Installation Problems You may need to reconfigure the compu ter when you add or remove hardware, such as an addi tional drive or expansion card. If you install a plug an d play device, Windows auto matically r ecognizes the device and configures the computer.
Power LED flashes Red five times, once every second, follo wed by a two second pause, and the computer beeps five times. (Beeps s top after fifth itera tion but LEDs con tinue flashing.
Solving Network Problems Some common causes an d solutions for network pro b lems are liste d in the following tab le. These guidelines do not discu ss the process of debugging the network cabling. Table C-11 Solving Network Prob lems Wake-on-LAN featu re is not functioning.
Network driver does not detect netw ork controller. Cause Solution Network controller is disabled. 1. Run Computer Setup and enable networ k controller. 2. Enable the network controller in the o perating system via Device Manager . Incorrect network driver.
Diagnostics passe s, but the computer does not communica te with the network. Cause Solution Network drivers are not loaded, or driver parameters do not match current configuration. Make sure the network drivers are loaded and that the driver parameters match the configuration of the netw ork controller.
System setup utility reports unprogrammed EEPROM. Cause Solution Unprogrammed EEPROM. Contact an authorized service provider. Solving Memory Problems If you encounte r memory problems, some common causes and so lutions are listed in the fol lowing table.
Insufficient memory error during operation. Cause Solution Too many Terminate and Stay Resid ent programs (TSRs) are installed. Delete any TSRs that you do not need. You have run out of memory for the application. Check the memory requireme nts for the application or add more memory to the computer.
Solving Processor Problems If you encounte r processor problems, common ca uses and solutions are listed in the following table. Table C-13 Solving Processor Problems Poor performance is experienced. Cause Solution Processor is hot. 1. Make sure the airflow to the computer is not blo cked.
Solving CD-ROM and DVD Problems If you encounte r CD-ROM or DVD p roblems, see the common causes and solutions listed in the following table or to the documentatio n tha t came with the option al device. Table C-14 Solving CD-ROM and DVD Problems System will not bo ot from CD-ROM or DVD drive.
Movie will not play in the DVD drive. Cause Solution Movie may be regionalized for a different country. See the documentation that came with the DVD drive. Decoder software is not installed. Install decoder software. Damaged media. Replace media. Movie rating locked out by parental lock.
USDT computer boots too slow a fter removing a CD-R OM or DVD drive. Cause Solution The system is searching for the drive during boot because the drive cable is still atta ched to the system board.
Solving Front Panel Component Problems If you encounte r problems with devices connecte d to the front panel, refe r to the common cau ses and solutions listed in the foll owing table. Table C-16 Solving Front Panel Component Problem s A USB device, headpho ne, or microphone is not recognized by the com puter.
Solving Internet Access Problems If you encounte r Internet acce ss problems, consult your Internet Service P rovider (IS P) or refe r to the common causes and solutions listed in the following table. Table C-17 Solving Internet Acce ss Problems Unable to connect to the Internet.
Cannot automatically la unch Internet progra ms. Cause Solution You must log on to your ISP before some programs will st art. Log on to your ISP and launch the desired program.
Internet takes too long to download Web sites. Cause Solution Modem is not set up properly. Verify that the modem is connected and communicating properly. Windows XP 1. Select Start > Control Panel . 2. Double-click System . 3. Click the Hardware tab.
Solving Software Problems Most software problems occu r as a result of the foll owing: ● The application wa s not installed or configured co rrectly. ● There is insufficient m emory available to run the application. ● There is a conf lict between a pplications.
D Password Security and Resetting CMOS This computer supports security password featur es, which ca n be established through the Comput er Setup Utilities menu. This computer supports two se curity password fe atures that are e stablished through the Co mputer Setup Utilities menu : setup password a nd power-on password.
Resetting the Password Jumper To disable the power-on or se tup password features , or to clear the pow er-on or setup passwords, complete the fo llowing steps: 1. Shut down the operating system properly, then turn off the computer and any external devices, and disconnect the power cord from th e power outlet.
Clearing and Resetting the CMOS The computer’s configuratio n memory (CMOS) stores information about the computer’s configuration. 1. Turn off the compu ter and any external devices, an d disconnect the power cord from the power outlet. 2. Disconnect the keyboard, monitor, a nd any other exte rnal equipment conne cted to the computer.
6. Reconnect the external devices. 7. Plug in the comput er and turn on power. NOTE: You will receive POST erro r messages after cle aring CMOS and rebo oting advising you that configuration changes have occurred. Us e Computer Setup to reset any special system setups along wi th the date and time.
E Drive Protection System (DPS) The Drive Protection System (DPS) is a dia gnostic tool built into the hard d rives installed in some computers. DPS is designed to help diagno se proble ms that might resu lt in unwarrante d hard drive replacement.
Accessing DPS Through Computer Setup When the computer does not p ower on properly yo u should use Computer Setup t o access the DPS program. To access D PS, perform the followin g steps: 1. Turn on or restart the compu ter. 2. When the F10 Setup message appears in the lo wer-right corner of the screen, press the F10 key.
F System Recovery System Recovery completely e rases and reformat s the hard disk drive, dele ting all data files you have created, and th en reinstal ls the operating system, p rograms, and drivers. However, yo u must reinstall any softw are that was not inst alled on the co mputer at the factory.
System Recovery options You should attempt a System Recovery in the followi ng order: 1. Through the hard disk d rive, from the Windows 7 Start menu. 2. Through the hard disk drive, by pressing the F1 1 key on the ke yboard during system startup. 3. Through recovery media tha t you create.
If Windows 7 is not re sponding, but th e computer is working, follow these step s to perform a System Recovery. 1. Turn off the compute r. If necessary, press and hol d the Power bu tton until the compu ter turns off. 2. Disconnect all pe ripheral devices from t he computer, except the keyboard and mouse.
8. If you are prompted to back up your file s, and you have no t done so, ta p Back u p your files first (recommend ed) , and then tap Next . Otherwise, tap Recover without ba cking up you r files , and then tap Next . 9. If you are prompted to insert the next recovery di sc, do so.
3. Tap Create reco very media using blan k DVD(s) , and then tap Next . 4. Follow the on-screen instruction s. Label each di sc as you make it (for example, Recovery 1, Recover y 2). To create a re covery USB flash drive: 1. Close all open prog rams. 2.
G Specifications Table G -1 Specifications Desktop Dimensions (in the desktop position) Height Width Depth 3.95 i n 13.3 in 14.9 in 10.0 cm 33.8 cm 37.
Table G -1 Specifications (conti nued) Power Supply Power Output Rated Input Current (maximu m) 1 Rated Line Frequency Operating Line Frequency Range Max Allowable Leakage Current Power Supply Fan 115.
Index A access panel spare part number 28, 39 access panel, locke d 100 audible code s 94 audio connectors 2, 3 audio problems 115 B baffle removal and replaceme nt 69 spare part number 28, 35, 69 bat.
H hard drive installing 66 proper handling 25 removing 66 SATA characteristics 17 spare part number 54 spare part numbers 28, 35 hard drive problems 105 hardware insta llation problems 121 headphone c.
expansion card 46 expansion slot cover 48 front b ezel 40 hard drive 66 media card reader 61 optical drive 57 PCI card 49 PCI Express card 50 resetting CMOS 137 password jumper 137 S safety and comfor.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il HP (Hewlett-Packard) D3K19UT#ABA è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del HP (Hewlett-Packard) D3K19UT#ABA - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso HP (Hewlett-Packard) D3K19UT#ABA imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul HP (Hewlett-Packard) D3K19UT#ABA ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il HP (Hewlett-Packard) D3K19UT#ABA, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del HP (Hewlett-Packard) D3K19UT#ABA.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il HP (Hewlett-Packard) D3K19UT#ABA. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo HP (Hewlett-Packard) D3K19UT#ABA insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
