Manuale d’uso / di manutenzione del prodotto BF40D (2014) del fabbricante Honda
Vai alla pagina of 143
PANTONE 288 CVC DIC F101 BLACK BF40D50D_AH-OM表紙31ZZ4620 BF40D50D_AH-OM表紙31ZZ4620 BF40D50D_AH-OM表紙31ZZ4620 背幅4mm 背幅4mm 背幅4mm Includes US and Canadian Models 英 N HC AH EM3 31ZZ4620 00X31-ZZ4-6200 1000.
Keep this Owner ’ s Manual handy , so you ca n refer to it at any time. This Owner ’ s Manual is considered a permanent part of th e outboard motor and should remain with the outboard motor if resold.
1 INTRODUCTION Congratulations on your selection of a Honda outboard motor . W e are certain you will be pleased with your purchase of one of the finest outboard motors on the market. W e want to help you get the best results from your new outboard motor and to operate it safely .
2 INTRODUCTION A FEW WORDS ABOUT SAFETY Y our safety and the safety of others are very important. And using this outboard motor safely is an important responsibility . T o help you make informed decisions about safety , we have p rovided operating procedures and oth er information on labels and in this manual.
CONTENTS 3 OUTBOARD MOTOR SAFETY ................... ................ 7 IMPORTANT SAFETY INFORMATION .............. 7 SAFETY LABEL LOCATIONS ....................... ....... 9 CONTROLS AND FEATURES ..................... .............. 13 CONTROL AND FEATURE IDENTIFICATION CODES .
CONTENTS 4 INDICATORS ..................... .................. .................. 32 Alternator (ACG) Indicator ................................. 32 Malfunction Indicator ................................. ......... 32 Oil Pressure Indicator ..........
CONTENTS 5 CRUISING ................. .................. ...................... ..... 60 TRIM TAB ................................... .................. ......... 63 SHALLOW WATER OPERATION ................. ..... 63 MOORING, BEACHING, LAUNCHING .....
CONTENTS 6 TAKING CARE OF UNEXPECTED PROBLEMS ... 100 ENGINE WILL NOT START ....................... ....... 100 HARD STARTING OR STALLS AFTER STARTING ..................... .................. ................ 103 ENGINE OVERHEATS .....................
7 OUTBOARD MOT OR SAFETY IMPOR T ANT SAFETY INFORMA TION The Honda BF40D/BF50D out board motors are designed for use with boats that have a suitable manufacturer ’ s power recommendation. Other uses can result in injury to the operator or damage to the outboard motor and other property .
8 OUTBOARD MOT OR SAFETY Refuel With Car e • Gasoline is extremely flammable, and gasoline vapor can explode. Refuel outdoors, in a well-ventilated area, with the engine stopped. Never smoke near gasoline, and keep other flames and sparks away . • Refuel carefully to avoid spilling fuel.
9 OUTBOARD MOTOR SAFETY SAFETY LABEL LOCA TIONS US, Puerto Rico, and US V irgin Islands T ypes The label shown here contain s importan t safety information. Please read it ca refully . This label is considered a permanent part of your outboard motor .
10 OUTBOARD MOT OR SAFETY The label shown here contain s importan t safety information. Please read it ca refully . This label is considered a permanent part of your outboard motor . If the label comes off or becomes hard to read, contact an authorized Honda Marine dealer for a replacement.
11 OUTBOARD MOTOR SAFETY POR T ABLE FUEL T ANK [standard equipment (Canadia n types)] [optional e quipment ( American types)] FUEL CAUTION 31ZZ46230.book 11 ペ ージ ２０１３年９月２７日.
12 OUTBOARD MOT OR SAFETY Canadian T ypes • Honda outboard motor is designed to give safe and dependable service if operated according to instruct ions. Read and understand the Owner’s Manual before operating the outboard motor. Fail ure to do so could result in personal injury or equipment damage.
13 CONTROLS AND FEA TURES CONTROL AND FEA TURE IDENTIFICA TION CODES *: Optional equipm ent Refer to this chart for an explanation of the T ype Codes used in this manual to identify control and feature applications.
14 CONTROLS AND FEA TURES COMPONENT AND CONTROL LOCA TIONS LH and LHT T ypes (tiller handle) ENGINE COVER LA TCH (front) SP ARK PLUG (inside the cover) ENGINE COVER ENGINE COVER LA TCH (rear) POWER TI.
15 CONTROLS AND FEA TURES INDICA TORS (Oil pressur e, Overheat, Alternator , Malfunction) EMERGENCY STOP SWITCH EMERGENCY STOP SWITCH LANY ARD IGNITION SWITCH IGNITION SWITCH KEY EMERGENCY STOP SWITCH CLIP STEERING FRICTION ADJUSTER POWER TRIM/TIL T SWITCH (LHT type only) GEARSHIFT LEVER THROTTLE FRICTION ADJUSTER THROTTLE GRIP 31ZZ46230.
16 CONTROLS AND FEA TURES LR T and XRT T ype s (r emote contro l) ENGINE COVER LA TCH (front) FUEL LINE CONNECTOR STERN BRACKET ANODE MET AL GEAR OIL CHECK SCREW W ASH SCREW GEAR OIL DRAIN/FILL SCREW .
17 CONTROLS AND FEA TURES Remote Control Box Side-Mount Contr ol T ype [standard equipment (LR TC type)], [optio nal equipment (LRT A and XRT A types)] GEARSHIFT/THROTTLE CONTROL LEVER POWER TRIM/TIL .
18 CONTROLS AND FEA TURES Portable Fuel T ank [standard equipment (Canadian types)] [optional equipment (American types)] VENT KNOB FUEL FILLER CAP FUEL HOSE (standard equi pment) FUEL HOSE CONNECTOR (female) PRIMING BULB POR T ABLE FUEL T ANK FUEL GAUGE 31ZZ46230.
19 CONTROLS AND FEA TURES Tr i m M e t e r [standard equipment (Canadian types)] [optional equipment (LR T A and XR T A types)] T achometer [standard equipment (Canadian types)] [optional equipment (LR T A and XR T A types)] T rolling Contr ol Switch Panel [optional equipment (other LHA and LHTC types)] TRL (T rolling) CONTROL SWITCH 31ZZ46230.
20 CONTROLS AND FEA TURES CONTROLS LH and LHT T ypes (tiller handle) Ignition Switch The ignition switch controls the ignition system and the starter motor . T urning the ignition switch key to the ST AR T position operates the starter motor . The key auto matically returns to the ON positio n when released from the ST AR T position.
21 CONTROLS AND FEA TURES The emergency stop switch clip must be inserted in the emer gency stop switch in order for the engine to start and run. The emergency stop switch lanyard must be attached securely to the operator or to the operator ’ s PFD (Personal Flotation Device).
22 CONTROLS AND FEA TURES Throttle Friction Adjuster The throttle friction adjuster adjusts resistance to throttle grip rotation. T urn the adjuster clockwise to increase friction fo r holding a throttle setting while cruising. T urn the adjus ter counterclockwise to decrease friction for easy throttle grip rotation.
23 CONTROLS AND FEA TURES T ransom Angle Adjusting Rod (LH type) The transom angle adjusting rod limits the tilt angle of the outboard motor when fully lowered. Proper adjustment prevents the outboard motor from being trimmed too low (p. 60 ). There are five transom angle adjustment positions.
24 CONTROLS AND FEA TURES LR T and XRT T ypes (remote contr ol/side-mount control type) [standard equipment (LR TC type)] [optional equipment (LR T A and XR T A types)] For panel-mount or top-mount remote control information, refer to the instructions provided with the remote control equipm ent.
25 CONTROLS AND FEA TURES Emergency S top Switch Clip and Emergency S top Switch The emergency stop switch clip must be inserted in the emer gency stop switch in order for the engine to start and run. The emergency stop switch lanyard must be attached to the operator ’ s PFD (Personal Flotation Device) or to the operator securely .
26 CONTROLS AND FEA TURES Gearshift/Throttle Control Lever The gearshift/throttle control lever controls eng ine speed and s elects F (forward), N (neutral), or R (reverse) gears. Moving the control lever 30° from N (neutral) selects th e gear , and further movement increases e ngine speed.
27 CONTROLS AND FEA TURES Use the fast idle le ver to accelerate engine warm-up after starting the engine. Do not use the fast idle lever when starting the engine. See page 50 for engine warm-up instructions. The fast idle lever allows you to increase the idle speed only when the control lever is in the N (neutral) position.
28 CONTROLS AND FEA TURES LHT , LR T and XRT T ypes (power trim/tilt) Power T rim/T ilt Switch The power trim/tilt sw itch is located on the control lever . It is a rocker switch with UP and DN (down) positions for changing the angle of the outboard motor .
29 CONTROLS AND FEA TURES Manual Relief V alve The outboard motor can be tilted manually after open ing the manual relief valve. This allows the outboard motor to be tilted up or down when no battery is connected. Check that nobody is unde r the outboard motor be fore opening the manual relief valve.
30 CONTROLS AND FEA TURES Common Controls T ilt Lock Lever The tilt lock lever is used to support the outboard motor in the fully-raised position. When the boat is to be moored for a long time, tilt the ou tboard motor up as far as it will go.
31 CONTROLS AND FEA TURES INSTRUMENT S T rim Meter [standard equipment (Canadian types)] [optional equipment (LR T A and XR T A types)] The trim meter indicates the relative trim angle of the outboard motor . Refer to the trim meter when using the power trim/tilt switch to achieve the best performance from the boat.
32 CONTROLS AND FEA TURES INDICA TORS The indicator lights come on and the buzzer sounds when yo u turn the ignition switch ON, allowing you to see that they are working. If an indicator does not light during this test, it cannot alert you if that system develops a problem.
33 CONTROLS AND FEA TURES When the engine control system detects an engine control system malfunction, the malfunction indicator turns on and the buzzer sounds at one-second intervals. Oil Pressur e Indicator When the oil pressure indicator is lit, oil pressure is OK.
34 CONTROLS AND FEA TURES Overheat Indicator When the alert triggers, the overheat indicator comes on and the buzzer sounds a steady tone as the engine speed is reduced to 1,800 rpm. If the condition persists for another 20 seconds, the engine shuts of f.
35 CONTROLS AND FEA TURES The cooling sy stem indicator discharge port can also become plugged. OTHER FEA TUR ES Overrev Limiter The engine is equipped with an overrev limiter to prevent the possibility of mechanical damage from excessive engine speed.
36 CONTROLS AND FEA TURES Fuel Filler Cap V ent Knob The fuel filler cap is provided with a vent knob to seal the p ortable fuel tank for carrying it to and from the boat. Open the vent by tu rning the vent knob counterclo ckwise all the way before starting the engine.
37 CONTROLS AND FEA TURES The anodes are made of a sacrificial material that helps to protect the outboard motor from corrosion. There are two anodes on the gear case, one on the stern bracket and two small anodes in the water passages of the engine bloc k.
38 BEFORE OPERA TION ARE YOU READY TO GET UNDER W A Y? Y our safety is your responsibility . A little time spent in preparation will significantly reduce your risk of injury . Knowledge Read and understand this manual. Know what the controls do and how to operate them.
39 BEFORE OPERA TION Safety Inspec tion • Before each use, look around underneath the engine for signs of oil or gasoline leaks. • If you are using the po rtable fuel tank (standard or optional equipment), make sure it is in good condition and properly secured in the boat (p.
40 BEFORE OPERA TIO N T iller Handle Height/Angle Adjustment (LH and LHT types) The tiller handle height and angle can be adjusted to three positions by changing the installation direction of the height adjustment block. Select a suitable height and angle for the operator and secure the block.
41 OPERA TION SAFE OPERA TING PRECAUTIONS T o safely realize the full potential of this outboard motor , you need a complete understanding of its operation and a certain amount of practice with its controls.
42 OPERA TION TRANSOM ANGLE ADJUSTMENT (LH T ype) The transom angle adjusting rod limits the tilt angle of the outboard motor when fully lowered. Proper adjustment prevents the outboard motor from being trimmed too low (p. 60 ). T o adjust, first tilt the outboard motor so it is not resting on the rod.
43 OPERA TION POR T ABLE FUEL T ANK [standard equipment (Canadian types)] [optional equipment (American types)] Place the portable fuel tank in a well-ventilated location, away from direct sunlight, to reduce the possibility of a gasoline vapor explosion.
44 OPERA TION Connect the fuel hose to the tank and the outboard motor , as shown. Be sure both connectors snap securely into place. Always disconnec t the fuel hose when storing or transporting the outboard motor . FUEL PRIMING If you are using a portable fuel tank, turn the portable fu el tank ven t knob counterclockwise to the open position.
45 OPERA TION INFREQUENT OR OCCASIONAL USE If your outboard motor will be used on an infrequen t or intermittent basis, please refer to the fuel section of the STORAGE chapter (p. 94 ) for additional information regarding fuel deterioration. ST AR TING THE ENGINE Control Page Side-Mount Control T ype .
46 OPERA TION 2. Check the position of the gearshift lever . It must be in the N (neutral) position for starting. The engine will not start if the gearshift lever is in the F (forward) or R (reverse) position. 3. Align the engine start symbol ‘‘ ’ ’ on the tiller handle with the pointer ‘ ‘ ’ ’ on the throttle grip.
47 OPERA TION If the engine fails to start within 5 seconds, release the key and wait at least 10 seconds before operating the starter again. • Using the electric starter for mor e than 5 seconds at a time will overheat the starter motor and can damage it.
48 OPERA TION LRT and XRT T ypes (remote control) Side-Mount Control T ype [standard equipment (LR TC type)] [optional equipment (LR T A and XR T A types)] 1. Put the emergency stop switch clip in the emergency stop switch, and securely to the operator or to the operator ’ s PFD (Personal Flotatio n Device).
49 OPERA TION 3. Leave the fast idle lever in the ST AR T (fully lowered) po sition. The fast idle lever cannot be raised unless the control lever is in the N (neutral) position. The control lever cannot be moved away from the N (neutral) position unless the fast idle lever is lowered.
50 OPERA TION 6. Before getting underway , allow the engine to warm-up sufficiently to ensure good performance. Above 41°F (5°C), warm-up the engine for at least 3 minutes. Below 41°F (5°C), warm-up the engine for at least 5 minutes at 2,000 rpm. Raise th e fast idle lever to achieve ap proximately 2,00 0 rpm.
51 OPERA TION EMERGENCY ST AR TING If the battery is discharged or the starter motor is inoperative, you can start the engine manually using the emergency starter rope supplied with the outboard motor . 1. T urn the ignition switch key to the OFF position (p.
52 OPERA TION 5. Set the controls the same as for normal starting (p. 45 – 46 , 48 – 49 ). T urn the ignition switch key to the ON position. 6. Set the alternator pulley so the cutouts are on the right and left sides of the alternator pulley as shown.
53 OPERA TION 8. If the fast idle control(s) was used to start the engine, return the control(s) to the normal operating position as the engine warms up. During the warm-up period, check the oil pressure indicator (p. 33 ), overheat indicator (p. 34 ), and cooling system indicator (p.
54 OPERA TION STOPPING THE ENGINE Emergency Engine S topping LH and LHT T ypes (tiller handle) LRT and XRT T ypes (remote control) T o stop the engine in an emergency , pull the emergency stop switch clip out of the emer gency stop switch by pulling the emergency stop switch lanyard.
55 OPERA TION Normal Engine S topping LH and LHT T ypes (tiller handle) LRT and XRT T ypes (remote control) Side-Mount Control T ype 1. Move the throttle grip to the slowest speed and the gearshift lever or control lever to the N (neutral) position.
56 OPERA TION LH and LHT T ypes (tiller handle) 2. T urn the ignition switch key to the OFF position to stop the engine. In the event that the engine does not stop when the ignition switch key is turned to the OFF position, pull the emergency stop switch cli p out of the emergency stop switch by pulling the emergenc y stop swi tch lanyard (p.
57 OPERA TION GEARSHIFT AND THROTTLE OPERA TION LH and LHT T ypes (tiller handle) T o shift gears, turn the throttle grip to the SLOW position; then move the gearshift lever to select the F (forward), N (neutral), or R (reverse) gears. The engine can be started with the gearshift lever in the N (neutral) position only .
58 OPERA TION LRT and XRT T ypes (remote control) T o shift gears, move the control lever to select the F (forward), N (neutral), or R (reverse) gear . The control lever cannot be mo ved from the N (neutral) position unless the neutral release lever is squeezed.
59 OPERA TION STEERING LH and LHT T ypes (tiller handle) Steer by moving the tiller handle opposite the direction you want t he boat to turn. S teering Friction Adjuster Use the steering friction adjuster to help hold a steady course while cruising. Move the adjuster to the LOCK direction to increase steering friction for holding a steady course.
60 OPERA TION CRUISING Engine Speed For best fuel economy , limit the throttle opening to 80%. Use the throttle fricti on contro l (p. 57 , 58 ) to help you hold a steady speed. For rough water conditions or lar g e waves, slow down to prevent the propeller from rising ou t of the water .
61 OPERA TION It is necessary to trim the angle of the outboard motor to compensate for changes in boat load, weight distribution, water conditions, or propeller selection. Under normal conditions, the boat will perform best when the antiventilation plate is level with the water surface.
62 OPERA TION T rolling Speed Contr ol [optional equipment (except LHA and LHTC types)] DN: Reduce engine speed UP: Increase engine speed Place the outboard motor in-gear with the throttle control in the fully closed (idle) position. Press and hold the UP or DN side of the TRL contro l switch to activate the T rolling Speed Control.
63 OPERA TION TRIM T AB If steering effort is not equal in both directions, adjust the trim tab to compensate for ‘ ‘torque steer ,’ ’ which is the reaction of the outboard motor to propeller rotation. Adjust the trim tab with the engine stopped.
64 OPERA TION T o tilt the outboard motor , move the tilt lever to the FREE (TIL T) position, then raise the outboard motor to the desired position by pulling on the engine cover grip. Do not use the tiller handle as a lever to raise the outboar d motor .
65 OPERA TION MOORING , BEACHING , LAUNCHING Before tilting up, leave the outboard motor in the running position for one minute after stopping the engine to drain the water from inside the engine. Stop the engine and disconnect the fuel hose from th e outboard motor before tilting the outboard motor .
66 OPERA TION The outboard motor can also be tilted manually after open ing the manual relief valve. This feature enables the outboard motor to be tilted up or down when no batte ry is connected. For manual tilting, use a flat blade screwdriver to turn the valve counterclockwise 2 and a half turns.
67 SER VICING YOUR OUTBOARD MOTOR THE IMPOR T ANCE OF MAINTENANCE Proper maintenance is essential for safe, economical, and trouble-free operation. It will also help reduce air pollution.
68 SER VICING YOUR OUTBOARD MOTOR MAINTENANCE SAFETY Some of the most important safety precautions follow . However , we cannot warn you of eve ry conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you sho uld perform a given task.
69 SER VICING YOUR OUTBOARD MOTOR SP ARE SWITCH CLIP (LH and LHT T ypes) AND EMERGENCY ST AR TER ROPE Always carry the spa re switch clip and the em erge ncy starter ro pe onboard. The spare clip may either be stored in the tool bag or in an easily accessible location on the boat along with the emer gency starter rope.
70 SER VICING YOUR OUTBOARD MOTOR MAINTENANCE SCHEDULE Follow the MAINTENANCE SCHEDULE table and service your outboard motor accordingly . Please note, a claim for warranty coverage will not be denied simply because the maintenance schedule for your outboard motor was not followed.
71 SER VICING YOUR OUTBOARD MOTOR (1) Lubricate more frequently wh en used in salt water . (2) These items should be servic ed by your servicing dealer , unless you have the pr oper tools and are mech anically proficient. R efer to the Honda shop manual for serv ice procedures.
72 SER VICING YOUR OUTBOARD MOTOR TRIM T AB ADJUSTMENT The trim tab compensates for ‘ ‘torque steer ,’ ’ which is a reaction of the outboard motor to propeller rotation. If uncompensated, torque steer would make the outboard motor tend to turn to one side.
73 SER VICING YOUR OUTBOARD MOTOR MANUAL RELIEF V AL VE LHT , LRT and XRT T ypes The outboard motor can be tilted manually after open ing the manual relief valve. This feature enables the outboard motor to be tilted up or down when no batte ry is connected.
74 SER VICING YOUR OUTBOARD MOTOR Engine Oil Level Check Check the engine oil level with the engine stopped and the outboard motor in the vertical position. 1. Unlatch and remove the engine cover (p. 73 ). 2. Remove the oil level dipstick and wipe it clean.
75 SER VICING YOUR OUTBOARD MOTOR When you check the oil leve l with the dipstick, you might notice the engine oil appears milky or the oil level has incr eased. If you notice either condition, change the engine oil. See the followi ng table for an explanation of these conditions.
76 SER VICING YOUR OUTBOARD MOTOR Engine Oil Change An engine oil ev acuation device may be used to remove the engine oil. Drain the used oil while the engine is warm. W a rm oil drains quickly and completely . 1. Unlatch and remove the engine cover (p.
77 SER VICING YOUR OUTBOARD MOTOR 4. Remove the en gine oil drain bolt and sealing washer . 5. Allow the used oil to drain completely , then install a new sealing washer on the engine oil drain bolt, and tighten it securely . 6. Reinstall the drain bolt cover .
78 SER VICING YOUR OUTBOARD MOTOR Engine Oil Recommendations Oil is a major factor af fecting performance and service life. Use 4-stroke detergent oil. SAE 5W -30 is recommended for general use. Honda recommends that you use API service category SG, SH or SJ oil.
79 SER VICING YOUR OUTBOARD MOTOR 4. Inspect the spark plugs. Replace them if the electrodes are worn, or if the insulators are cracked or chipped. 5. Measure the spark plug electrode gap with a wire-type feeler gauge. Correct the gap, if necessary , by carefully bending the side electrode.
80 SER VICING YOUR OUTBOARD MOTOR Apply Honda Marine Corrosion Inh ibitor (or equivalent) to all areas under the engine cover and any exposed metal surfaces except the belts.
81 SER VICING YOUR OUTBOARD MOTOR REFUELING If you do not anticipate cycling through at least one complete tank of fuel within a 30 day perio d, we recommend adding Honda Marine Fuel Stabilizer each time you refuel. Portable Fuel T ank [standard equipment (Canadian types)] [optional equipment (American types)] FUEL T A NK CAP ACITY : 6.
82 SER VICING YOUR OUTBOARD MOTOR Refuel in a well-ventilated area. Fill the tank to the SAFE FILL LEVEL line. After refueling, in stall the cap and tighten it until you hear it click. Close the vent by turning the vent knob clockwise all the way , and return the fuel tank to t he boat.
83 SER VICING YOUR OUTBOARD MOTOR FUEL RECOMMENDA TIONS Use unleaded gasoline with a pump octane rating of 86 or higher . Y our outboard motor is certified to operate on unleaded gasoline. Unleaded gasoline produces fewer engine and spark plug deposits and extends exhaust system life.
84 SER VICING YOUR OUTBOARD MOTOR Fuel Filter/W ater Separator Inspection and Service The fuel filter is located under the engine cover between the fuel coupling and the fuel pump. W ater or sediment accumulation in the filter can cause loss of power or hard starting.
85 SER VICING YOUR OUTBOARD MOTOR 2. Inspect the filter for water and/or sediment accumulation. If water and/or sediment are present, clean the strainer cup and filter or replace the filter as described in the following steps. Always replace the filter at the scheduled replacement interval (p.
86 SER VICING YOUR OUTBOARD MOTOR 6. Unscrew the strainer cup from the filter body . 7. Thoroughly clean the strainer cup and fuel filter . If the fuel filter is contaminated, replace it with a new one. 8. Install the fuel filter , float, O-rings and strainer cup.
87 SER VICING YOUR OUTBOARD MOTOR 1 1. Connect the fuel hoses to the fuel filter securely with the hose clamps. Remove the fuel hose clips used to close the fuel hoses. 12. Securely connect the fuel hose connector to the outboard motor (refer to page 43 ).
88 SER VICING YOUR OUTBOARD MOTOR Fuel T ank Filter 1. Remove the four 5 mm screws using a flat screwdriver , then remove the fu el hose co nnector and fuel tank filter from the tank. 2. Clean the filter in nonflammable solvent. Inspect the fuel tank filter and the connector gasket.
89 SER VICING YOUR OUTBOARD MOTOR Propeller Replacement [standard equipment (Canadian types)] [optional equipment (American types)] Before replacing the propeller , remove the emergency stop switch clip from the emer gency stop switch to prevent any possibility of the engine being st arted while you are working with the propeller .
90 SER VICING YOUR OUTBOARD MOTOR 3. Install the propeller , the special spline washer and the plain washer . 4. Lightly tighten the castle nut by hand or wrench until the propeller has no free play . 5. T ighten the castle nut using a torque wrench. CASTLE NUT TIGHTENING TORQUE: 0.
91 CLEANING AND FLUSHING Cleaning and Flushing After each use in salt water or dirty water , thoroughly clean and flush the outboard motor with fresh water . T ouch up any damaged paint, and coat areas that ma y rust with Hond a Corrosion Inhibitor , or equival ent.
92 CLEANING AND FLUSHING 3. Cover the three wa ter intakes with duct tape as shown abov e. 4. Remove the sealing washer from the wash screw and install the sealing washer on the flush kit coupler . 5. Install the flush kit coupler into the W ASH screw hole and connect a fresh water hose to the garden hose adapter .
93 CLEANING AND FLUSHING 8. Start the engine. Monit or the cooling system in dicator . Stop the engine if water does not come out of the cooling system indicator and check the fresh water supply . 9. Allow the engine to run at idle for at least 5 minutes to clean the inside of the outboard motor .
94 ST ORAGE Fuel Depending on the r egion wher e you operate your outboar d, fuel formulations may deteriorate and oxidize rapidly . Fuel deterioration and oxidation can occur in as little as 15 days and may ca use damage to the fuel system. Please check with your servicing dealer for local storage r ecommendations.
95 ST ORAGE Draining the Fuel System Y ou can avo id fuel deterioration problems by drain ing the fuel tank and vapor separator . Before draining and checking the fuel system, check the fuel filter for contamination and/ or water accumulation. The fuel filter must be free of any contamination before proceeding (p.
96 STORAGE 5. T ilt the outboard motor up until gasoline flows out of the drain tube. 6. Leave it in that position until the gasoline stops flowing. 7. After thoroughly draining , tighten the drain screw securely . 8. Check the drained gasoline for the presence of water or contamination.
97 ST ORAGE Engine Oil 1. Change the engin e oil (p. 76 ). 2. Remove the spa rk plugs (p. 78 ), and remove the emergency stop switch clip from the emergency stop switch. 3. Pour 1 – 2 teaspoons (5 – 10 cm 3 ) (p. 111 ) of clean engine oil into each cylinder .
98 STORAGE If the outboard motor will be removed from the boat for storage, we recommend storing it vertically by mounting it on a commercially available stand. If it is necessary to store the outboard motor horizontally as show n, drain the vapor separator (p.
99 TRANSPOR TING WITH OUTBOARD MOTOR INST ALLED ON BOA T When trailering a boat with the outboard motor attached, always disconnect the fuel line from the portable fuel tank. LH and LHT T ypes (tiller handle) T ighten the steering friction adjuster to prevent the out board motor from moving while trailering the boat.
100 T AKING CARE OF UNEXPECTED PROBLEMS ENGINE WILL NOT ST AR T Possible Cause Correction Clip not inserted in emergency stop switch. Insert clip in emergency stop switch. Gearshift lever or control lever not in neutral position. Shift to neutral (p. 45 or 48 ).
101 T AKING CARE OF UNEXPECTED PROBLEMS ENGINE WILL NOT ST AR T Possible Cause Correction Out of fuel. Refuel (p. 81 ). Fuel vent closed (porta ble fuel tank). Open fuel filler cap vent (p. 36 ). Fuel hose not primed. Squeeze priming bulb (p. 44 ). Fuel filter or fuel tank filter clogged.
102 T AKING CARE OF UN EXPECTED PROBLEMS ENGINE WILL NOT ST AR T Possible Cause Correction Battery connections loose or corroded. Clean and tighten ba ttery connections. Battery discharged. Rechar ge battery . Fuse(s) blown. Replace fuse(s) (p. 105 ).
103 T AKING CARE OF UNEXPECTED PROBLEMS HARD ST AR TING OR ST ALLS AFTER ST AR TING Possible Cause Correction Throttle grip not in ST AR T position (tiller handle type). T urn throttle grip to ST AR T position (p. 46 ). Fast idle le ver ra ised (remote contro l/side-mount ty pe).
104 T AKING CARE OF UN EXPECTED PROBLEMS HARD ST AR TING OR ST ALLS AFTER ST AR TING ENGINE OVERHEA TS Possible Cause Correction Spark plugs faulty , fouled, or improperly gapped. Gap or replace spark plugs (p. 78 ). Fuel system malfunction, fuel pump failure, ignition malfunction, etc.
105 T AKING CARE OF UNEXPECTED PROBLEMS FUSES Electric S tarter Will Not Operate The 10A, 15A, and 30A fuses protect the electric starter relay and rel ated circuits.
106 T AKING CARE OF UN EXPECTED PROBLEMS Fuse Replacement Disconnect the battery cable at the battery negative (–) terminal befor e r eplacing the fuse. Failur e to do so may cause a short cir cuit. Main Fuse 1. Stop the engine and disconnect the battery cable.
107 T AKING CARE OF UNEXPECTED PROBLEMS OIL PRESSURE INDICA TOR GOES OFF AND ENGINE SPEED IS LIMITED LH and LHT T ypes (tiller handle) LRT and XRT T ypes (remote control) (internal buzzer) (GREEN) BUZZER (GREEN) 31ZZ46230.
108 T AKING CARE OF UN EXPECTED PROBLEMS If the throttle is closed suddenly after full throttle operation, engine speed may drop below the specified idle rpm, and that could activate the engine protection system momentarily . If low oil pressure activates the engine protection system, stop the engine, check the engine oil level (p.
109 T AKING CARE OF UNEXPECTED PROBLEMS If the engine is stopped aft er running at full throttle, and then restarted soon afterward, that could activate the engine protection system momentarily . If overheating activates the engine protection system, idle the engine in neutral, and check the cooling system indicator .
110 T AKING CARE OF UN EXPECTED PROBLEMS SUBMERGED OU TBOARD MOTOR A submerged outboard mo tor must be serviced immediately after it is recovered from the water in order to minimize corrosion. If there is a Honda Marine dealership nearby , take the outboard motor to the dealer immediately .
111 T AKING CARE OF UNEXPECTED PROBLEMS 6. Pour 1 – 2 teaspoons (5 – 10 cm 3 ) of engine oil into each spark plug hole, and then pu ll the emer gency starter rope several times to lubricate the inside of the cylinders. 7. Reinstall the spark plugs and alternator cover , and put the emergency stop switch cl ip into the emergency stop switch.
112 TECHNICAL INFORMA TION Serial Number Locations Record the product identification number , the engine serial number , and the date of purchase in the space provided on this page. Y ou will need these numbers when ordering parts, and when making technical or warranty inquiries (p.
113 TECHNICAL INFORMA TION Battery For complete informa tion, refer to the battery manufactu rer ’ s ins tructions. Minimum Requirements 12V – 52Ah/5HR (65Ah/20HR) (CCA420A) • Be car eful to avoid connecting the battery in r e verse polarity , as this will damage the battery-char ging system in the outboar d motor .
114 TECHNICAL INFORMA TION PGM-FI System The PGM-FI system uses sequential multiport fuel injection. It has two subsystems: Engine Control, and Fuel Control. The Engine Control Module (ECM) uses various sensors to determine how much air is going into the engine.
115 TECHNICAL INFORMA TION Problems That May Affect Emissions If you are aware of any of the following symptoms, h ave your engine inspected and repaired by yo ur servicing dealer . • Hard starting or stalling after starting. • Rough idle. • Misfiring or backfiring under load.
116 TECHNICAL INFORMA TION S tar Label US, Puerto Rico, and US V irgin Islands A Star label was applied to this outboard motor in accordance with the requirements of the California Air Resources Board. The S tar Label means Cleaner Marine Engine The Symbol for Cleaner Marine Engines: Cleaner Air and W ater - for healthier lifestyle and environment.
117 TECHNICAL INFORMA TION One S tar Low Emission The one-star label identifies engines that meet the Air Resources Board’ s Personal W atercraft and Outboard marine engine 2001 exhaust emission standards. Engines meeting these stan dards have 75% lower emissions than conventional carbureted two-stroke engine s.
118 TECHNICAL INFORMA TION Specifications MODEL BF40D Description code BBDJ Ty p e LH LRT Overall length 31.3 in (794 mm) 27.3 in (694 mm ) Overall width 14.6 in (372 mm ) Overall height 53.7 in (1,364 m m) T ransom height (when transo m angle is 12°) 20.
119 TECHNICAL INFORMA TION Specifications MODEL BF50D Description code BBEJ Ty p e LHT LRT, XRT Overall length 31.3 in (794 mm) 27.3 in (694 mm ) Overall width 14.6 in (372 mm ) Overall height 53.7 in (1,3 64 mm) LRT: 53.7 in (1,364 mm) XRT: 57.7 in (1,465 mm) T ransom height (when transo m angle is 12°) 20.
120 TECHNICAL INFORMA TION BF40D/BF50D T une-up Spark plug gap 0.024 – 0.028 in (0.6 – 0.7 mm ) See page 79 Idle speed 850 ± 50 rpm See shop manual V alve clearance Intake: 0.15 ± 0.02 mm Exhaust: 0.23 ± 0.02 mm See shop manual Other specifications No other adjustment is needed 31ZZ46230.
121 CONSUMER INFORMA TION Honda Publications (United S tates, Puerto Rico, and U.S. V irgin Islands) These publications will give you additional information for maintaining and repairing your outboard motor . Shop Manual This manual covers complete maintenance and overhaul procedures.
122 CONSUMER INFORMA TION Please include the following information in yo ur communication: • Y our name, addre ss and telephone number (complete with area code) • Model and complete serial number .
123 CONSUMER INFORMA TION W arranty Service Please remember that recommended maintenance interval servicing is not included in your warran ty coverage. Additionally , your warranty does not apply to the normal wear of items (such as spark plug(s), water pump, etc.
124 CONSUMER INFORMA TION W arranty S tatements The American Honda Distributor ’ s Limite d W arranty applies to outboards purchased in the United S tates , Puerto Rico, or the U.S. V irgin Islands. The Honda Canada Distributor ’ s W arranty applies to outboards purchase d in Canada.
125 CONSUMER INFORMA TION T o Qualify for This W arranty: The Honda Outboard Motor must be purchased from American Honda or a dealer authorized by American Honda to sell Honda Outboa rd Motors in the United States, Puerto Rico, or the U.S. V irgin Islands.
126 CONSUMER INFORMA TION Exclusions: This warranty does not ex tend to the following: • Conditions caused by lack of routine maintenance or improper storage (as outlined in the Owner ’ s Manual) .
127 CONSUMER INFORMA TION T o Qualify for This W arranty: 1. The accessories or replacement parts must be purchased from American Honda or a dealer , distributor , or distributor ’ s dealer authori zed by American Honda to sell those products in the United S tates, Puerto Rico, and the U.
128 CONSUMER INFORMA TION T o Obtain W arranty Service: Y ou must, at your ex pense, take the Honda Outboard Motor product accessory or replacement part or the outboard motor or bo at on which the acc.
129 CONSUMER INFORMA TION Emission Control System W arranty Y our new Honda outbo ard engine complies with both the U.S. EP A and State of California emissi on regulations. American Hond a provides the same em ission warranty coverage for outboard engines sold in all 50 states.
130 CONSUMER INFORMA TION OWNER’S W ARRANTY RESPONSIB ILITIES: As the outboard engine owner , you are responsible for the performance of the required maintenance listed in your owner ’ s manual. American Honda Motor Co., Inc. recommends that you retain all receipts covering maintenance on your outboa rd engine, but American Honda Motor Co.
131 CONSUMER INFORMA TION T O OBT AIN W A RRANTY SER VICE: Y ou must take your Ho nda outboard engine, along with your sales registration card or other pro of of original purchase date, at your expense, to any Honda Marine dealer that is authorized by American Honda Motor Co.
132 CONSUMER INFORMA TION EMISSION CONTROL SYSTEM W ARRANTY P AR TS: SYSTEMS COVERED BY THIS W ARRANTY : P AR TS DESCRIPTION: Fuel Metering Carburetor assembly , Throttle body , Fuel injector , Fuel p.
133 CONSUMER INFORMA TION Canada Distributor’s W arranty HONDA CANADA INC., for and on behalf of Honda Motor Co. Ltd., T okyo, Japan, gives the following written warranty on each new marine product manufactured by Honda Motor Co. Ltd., Jap an, distributed in Canada by Honda Canada Inc.
134 CONSUMER INFORMA TION THIS W ARRANTY DOES NOT COVER a) Any repairs required as a re sult of collision, accident, striking any object, misuse or lack of required maintenance; b) Any repairs require.
135 CONSUMER INFORMA TION REPLACEMENT P ARTS AND ACCESSOR Y W ARRANTY New genuine Honda replace ment parts or accessories sold to a consumer or installed by an au thorized Hond a Marine dealer which a.
136 INDEX Alternator (ACG) Indicator ......................... ................. 32 Anodes ..................... .................. ...................... ............. 37 Replacement ........ ............................................. ........ 88 ARE YOU READY TO GET UNDER W A Y ? .
137 INDEX Fast Idle Lever ............................... ....................... ........ 27 Fuel Filler Cap V ent Knob [standard equipment (Canadian types)], [optional equipment (American types)] ........... 36 Filter/W ater Separator Inspection and Service .
138 INDEX Oil Pressure Indicator .................... ....................... ........ 33 OIL PRESSURE INDICA TOR GOES OFF AND ENGINE SPEED IS LIMITED ................... ........... 107 OPERA TION ................................. ...................
139 INDEX T achometer [standard equipment (Canadian types)], [optional equipment (LR T A and XR T A types)] ....... 31 T AKING CARE OF UNEXPECTED PROBLEMS .. 100 TECHNICAL INFORMA TION .................. ............... 1 12 THE IMPOR T ANCE OF MAINTENANCE .
140 MEMO 31ZZ46230.book 140 ページ ２０１３年９月２７日 金曜日 午後１０時３１分.
PANTONE 288 CVC DIC F101 BLACK BF40D-50D_AH-OM表紙31ZZ4621 BF40D-50D_AH-OM表紙31ZZ4621 BF40D-50D_AH-OM表紙31ZZ4621 背幅4mm 背幅4mm 背幅4mm Includes US and Canadian Models US:K2 C:K3 英 N .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Honda BF40D (2014) è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Honda BF40D (2014) - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Honda BF40D (2014) imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Honda BF40D (2014) ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Honda BF40D (2014), ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Honda BF40D (2014).
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Honda BF40D (2014). Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Honda BF40D (2014) insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
