Manuale d’uso / di manutenzione del prodotto 08E91-E22-100B del fabbricante Honda
Vai alla pagina of 22
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 1 of 22 08E92-SVA-1B00-91 FEB 2008 200 6-2008 CIVIC 2-DOOR (A/T ONLY) REMOTE ENGINE STARTER SYSTEM INSTALLATION INSTRUCTIONS Accessory Application Publications No.
2 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 7 Foam cushion tapes Flange nut Clip Green relay (5-pin) Template Illustration of the Engine Starter System.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 3 of 22 Setting the Control Unit 3. Get the control unit. Using a small flat-tip screwdriver, adjust the switches on the control unit to the locations shown. Using a isopropyl alcohol on a shop towel, clean the area where the protective tape will attach.
4 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 9. Remove the driver’s dashboard lower cover (eight clips). 5202121T DRIVER’S DASHBOARD LOWER COVER 8 CLIPS 5202112T 8. If equipped, remove the driver’s dashboard under cover (turn the knob counterclockwise, and release two clips and pin).
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 5 of 22 1 2. Remove the column lower cover (two self-tapping screws and one screw). 5308530T 2 SELF-TAPPING SCREWS SCREW COLUMN LOWER COVER 1 0 . Lower the tilt lever, and pull the steering wheel toward you.
6 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 1 4 . Remove the sunvisor holders. Using a small flat- tip screwdriver, push the hook, and turn the holder 90°, then pull it out.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 7 of 22 1 9 . Pull away the weatherstrip from the left front pillar trim. Remove the left front pillar trim (two clips). 5202100T 2 CLIPS LEFT FRONT PILLAR TRIM WEATHERSTRIP 2 0 .
8 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 2 4. Measure the antenna cable as shown. Attach the three foam cushion tapes to the antenna cable in the measurement shown. 2 5 . Using isopropyl alcohol on a shop towel, clean the area where the antenna will attach.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 9 of 22 2 8. Route the antenna cable under the roof liner towards the driver’s side of vehicle, and down along the vehicle harness. Be careful not to crease the roof liner.
10 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 3 2 . Secure the antenna cable to the vehicle harness with a wire tie. Secure the wire tie between the vehicle harness branching points. 6D01281T VEHICLE HARNESS WIRE TIE ANTENNA CABLE BRANCHING POINT Installing the Control Unit Bracket 3 3 .
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 11 of 22 3 5 . Install the four relays to the engine starter harness relay blocks. Be careful to install the relays properly, or a malfunction will result. Routing the Engine Starter Harness 3 4 .
12 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 3 8 . Disconnect the vehicle 8-pin connector on the rear of the wiper switch and plug the engine starter harness 8-pin connectors into the vehicle 8-pin connector.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 13 of 22 4 0 . Wrap the vehicle 7-pin connector with one foam cushion tape, then place the vehicle 7-pin connector into the gap of the column. 6D01111T VEHICLE 7-PIN CONNECTOR (brown) (Squeeze into this area.
14 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 4 7 . Secure the engine starter harness to the vehicle harness using a wire tie: • With driver's dashboard under cover: Secure in the hole opened in the instrument panel.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 15 of 22 4 9. Disconnect the vehicle 42-pin, 4-pin, and 2-pin connectors. 5 1 . Wrap foam cushion tape to the vehicle 2-pin and 4-pin connectors and secure them with a wire tie.
16 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 5 4 . Install the clip from the engine starter harness to the fuse box bracket behind the fuse box.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 17 of 22 6D01312T ANTENNA CABLE TERMINAL (Connect first.) FRONT CONTROL UNIT ENGINE STARTER HARNESS 18-PIN CONNECTOR CONTROL UNIT BRACKET 5 7 . Install the control unit on the control unit bracket.
18 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 752501AS CAR ICON 752502AS CHECK BUTTON Input the VIN and other required information. 752504AS Select “R/C ENG STARTER.” CHECK BUTTON 752503AS Select “Honda Systems.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 19 of 22 752505AS “REMARKS” message CHECK BUTTON 752506AS Select “REGISTER REMOTE CONTROL ENGINE STARTER UNIT.” CHECK BUTTON 752507AS “Obtain PCM-code" message CHECK BUTTON 752509AS Input the PCM code.
20 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 1 1 . The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Click the check button. 1 2. The following message will display: Check that the engine can be started by the Transmitter.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 21 of 22 732904A Y DISPLAY COMMAND BUTTON START BUTTON TRANSMITTER STOP BUTTON FUNCTION CHECK Operating Conditions • The hood is closed. • The shift lever is in Park.
22 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. How to Program an Additonal Transmitter 1. Connect the HDS to the data link connector. 2. Start the HDS and click on the car icon. 3. Input the vehicle's VIN and other required information.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Honda 08E91-E22-100B è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Honda 08E91-E22-100B - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Honda 08E91-E22-100B imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Honda 08E91-E22-100B ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Honda 08E91-E22-100B, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Honda 08E91-E22-100B.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Honda 08E91-E22-100B. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Honda 08E91-E22-100B insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
