Manuale d’uso / di manutenzione del prodotto 02121NOS del fabbricante Holley
Vai alla pagina of 20
P/N 199R10382 2005 Mustang Wet Single Fogger Kit Kit Number 02121NOS OWNER’S MANUAL CONGRATULATIONS on purchasing your NOS Nitrous Oxide Inj ection Syst em! Your system is composed of the highest quality components availa ble. It should provide many miles of trouble-free performance when used corre ctly.
NOS nitrous oxide is legal for use in most states when used in accordance with state and l ocal traffic laws. NOS does not recommend or condone the use of its produc ts in illegal racing activiti es.
TABLE OF CONTENTS WHAT IS NITR OUS OXID E? .......................................................................................................4 Do’s and Don’ts of Nitrous Oxide...................................................................
WHAT IS NITROUS OXIDE? NITROUS OXIDE… …Is a cryogenic gas composed of nitroge n and oxygen molecul es …Is 36% oxygen by weight …Is non-flammable by itself …Is stored as a compressed liquid …Exists in two grades—U.S.P. and Nitrous Plus: U.
These kits have been design ed for safety and smoothness of operation. Nitrous oxide i s injected into the engine only when the following conditions are met: Bottle valve is opened. System is armed. Engine is at wide-open throttle. RPM conditions are met.
1.3 Kit Components Before beginning the install ation of your NOS kit, compare the components in your kit with those shown in Figure 1 an d listed i n Table 2.
Figure 1 Kit #02121NOS We t Kit Components Chapter 2 Kit Installation 2.1 Bottle Mounting Instructions NOTE: Disconnect the batter y ground before beginning insta llation. 2.1.1 Street Vehicles Accurate calibration of your NOS nitrous s ystem depends on the bottle remaining at a stable temper ature.
Figure 2 Nitrous Bottle Siph on Tube Orientation Figure 3 Nitrous Bottle Mount ing Orientations 2.2 Bottle Orientation Bottle placement is critical to the performance of your NOS nitr ous system.
Figure 4 Exploded View of Kit #02121NO S Wet NOS System 1. Install the bottle nut adapter (1) and Teflon washer (2) on the nitrous bottle (3). Tighten securel y. 2. Loosely install the bottle mounting brackets (4 & 5) on the nitrous b ottle, as shown in Figure 3E.
2. Install the Soft Plume Nozzle (22), taking into account the length of the nitr ous and fuel supply hoses a nd the intended location of the solenoids. Take into a ccount that the nozz le mounti ng bung (21) needs to be restraine d during final installation, and accessibility of a tool is important.
Figure 6 Mount the solenoid assembly to the dr iver’s s ide foremost valve cover bolt. See Figure 6 . Ensure that the assemb ly and lines do not interfere with engine accessorie s or body parts, and that hoses reach the Soft Plume nozzl e inlet ports without being stretched or kinked.
2. Install the 4AN fitting (12) into the injector block with Teflon paste, while secured in a soft jaw vise. Tighten securely. See Figure 9. WARNING! Do not tighten fittings whil e installed on the fuel rail. Insta ll these while secured in a soft jaw vise.
Figure 12 Electric Wiring Schematic 2.9 Electrical System Installation (WOT/Window S w itch) Refer to Figure 12 and the procedures in this se ction for electrical system installation. WARNING! Death or injury may occur from w orking on a charged electrical system.
Components Figure 13 Snap in rocker switch es & use backing plate with purge switch. Installed Figure 14 Figure 15 Hand tighten the purge switch. Installation complete Figure 16 Fig ure 17 4. Install the wiring relay and rel ay harness in the engine compar tment near the battery.
Coil #3 is closest to the firewall. Coil #1 is closest to the radiator. Figure 18 Figure 19 11. Connect the bro wn / yellow striped wire on the WOT/W indow Sw itch to the green / white striped wire of coil #3 (cylinder 3) on the car. See Figure 19. 12.
2.10 WOT/Windo w Switch Troubleshooting- Veri fying the operation of the NOS WOT/Window Switch NOTE: NOS highly recommen ds that the user NOT ch ange the factory WOT/W indow Switch settings. The WOT/Window Switch should be set at the - 300 0 rpm (low) and 6000 rpm (high) - default settings.
Chapter 3 Routine Maintenance 3.1 Nitrous Solenoid Filter When nitrous bottles are refilled they can bec ome contaminated with debris, if the refiller does n ot have an adequate filter in their transfer pump mechanism. Contaminants in the bottle will ev entually become lodged in the nitrous solenoid filt er fitting .
Figure 23 Exploded View of a Ty pical Solenoid Appendix A Troubleshooting Guide The troubleshooting chart on the foll owing pages should hel p det ermine and rectif y most problems with your installed NOS system. If you still need assistance determining or fixin g pr oblems, call the NOS Technical Support at 1-866-GOHOLLEY.
Mismatched N 2 O/fuel jetting. Compare jetting to recommended values. Install correct jets. Excessive fuel pressure. Install fuel pressure gauge, such as NOS P/N 15906NOS, in the fuel line. Measure the pressure during acceleration with the system activated.
Nitrous Oxide Accessories NOS systems are calibrated for optimum pe rformance with a bottle pressu re of 900-950 psi. The pressure will change with temperature. Heater kits are thermost atically controlled to keep the bottle near 85° F to provide correct pressure.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Holley 02121NOS è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Holley 02121NOS - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Holley 02121NOS imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Holley 02121NOS ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Holley 02121NOS, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Holley 02121NOS.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Holley 02121NOS. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Holley 02121NOS insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.