Manuale d’uso / di manutenzione del prodotto OM-947 212 149D del fabbricante Hobart Welding Products
Vai alla pagina of 48
OM-947 212 149D 2006 − 08 Processes Arc Welding Power Source And Wire Feeder Description MIG (GMAW) W elding (Optional) Flux Cored (FCA W ) W elding Handler 125 A n d H - 9 B G u n R File: Flux Core.
Hobart W elders manufactures a full line of welders and welding related equipment. For information on other quality Hobart products, contact your local Hobart distributor to receive the latest full line catalog or individual specification sheets. T o locate your nearest distributor or service agency call 1-877-Hobart1 or visit our website at www .
T ABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T ABLE OF CONTENTS SECTION 8 − WIRE WELDING GUIDELINES 28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1. T ypical FCA W Process Connections 28 . . . . . . . . . . . . . . . . . . . . . . . .
OM-947 Page 1 SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING som _3/05 Y W arning: Protect yourself and others from injury — read and follow these precautions. 1-1. Symbol Usage Means W arning! W atch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols.
OM-947 Page 2 Arc rays from the w elding process produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin. Sparks fly of f from the weld.
OM-947 Page 3 1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. D Do not install or place unit on, over , or near combustible surfaces. D Do not install unit near flammables. D Do not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.
OM-947 Page 4 1-5. Principal Safety Standards Safety i n W elding, Cutting, and Allied Processes, ANSI Standard Z49.1, from Global Engineering Documents (phone: 1-877-413-5184, website: www .
OM-947 Page 5 SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE A V ANT UTILISA TION fre_som _3/05 Y A vertissement : s e protéger et protéger les autres contre le risque de blessure — lire et respecter ces consignes.
OM-947 Page 6 Le rayonnement de l’arc du procédé de soudage génère des rayons visibles et invisibles intenses (ultraviolets et infrarouges) susceptibles de provo- quer des brûlures dans les yeux et sur la peau. Des étincelles sont projetées pendant le soudage.
OM-947 Page 7 2-3 . Dange rs suppléme ntaire s en r elation a vec l’installa tion, le f onctionneme nt et la m aintena nce Risque D’INCENDIE OU D’EXPLO- SION. D Ne pas placer l’appareil sur , au-dessus ou à proximité de surfaces inflammables.
OM-947 Page 8 2-5. Princi pales nor mes de sécuri té Safety i n W elding, Cutting, and Allied Processes, ANSI Standard Z49.1, de Global Engineering Documents (téléphone : 1-877-413-5184, site In- ternet : www .
OM-947 Page 9 SECTION 3 − SPECIFICA TIONS 3-1. Specifications Rated Welding Output Amperage Range Maximum Open- Circuit V oltage DC Amperes Input at Rated Load Output 1 15 V , 60 Hz, Single- Phase KV A KW W eight W/ Gun Overall Dimensions 90 A @ 1 9 V olts DC, 20% Duty Cycle 63 A @ 2 1 V olts DC, 20% Duty Cycle * 30 − 125 29 20 15 * 2.
OM-947 Page 10 3-3. V olt-Ampere Curves The volt-ampere curves show the minimum and maximum voltage an d amperage output capabilities of the welding power source. Curves of other settings fall between the curves shown. ssb1.1 10/91 − 210 518 8.0 13.
OM-947 Page 1 1 4-2. Process/Polarity T able Process Polarity Cable Connections P rocess P o l ar i ty Cable T o Gun Cable T o Work Clamp FCAW − Self-shielding wire − no shielding gas DCEN − Str.
OM-947 Page 12 4-4. Installing Gas Supply This Section only applies to MIG units or units equipped with MIG kit. NOTE Obtain gas cylinder and chain to running gear , wall, or other stationary support so cylinder cannot fall and break off valve. 1 Cap 2 Cylinder V alve Remove cap, stand to side of valve, and open valve slightly .
OM-947 Page 13 4-5. Installing Wire Spool And Adjusting Hub T ension When a slight force is needed to turn spool, tension is set. 1/2 in T ools Needed: Ref. 802 971-C / 803 012 / 803 013 -B Installing 8 in (203 mm) Wire Spool Installing 4 in (102 mm) Wire Spool When a slight force is needed to turn spool, tension is set.
OM-947 Page 14 4-6. Selecting A Location And Connecting Input Power For 1 15 V AC Model 1 Rating Label 2 Grounded Receptacle A 1 15 volt, 20 ampere individual branch circuit protected by time-de- lay fuses or circuit breaker is re- quired.
OM-947 Page 15 4-7. Installing Contact T ip And Nozzle T ools Needed: Ref. 804 241-A Y T ur n off welding power source. 1 Nozzle Remove nozzle. 2 Contact T ip 3 Tip Adapter Thread welding wire through gun (see Section 4-8). Slide contact tip over wire and tighten tip into tip adapter .
OM-947 Page 16 4-8. Threading Welding Wire 1 Wire Spool 2 Welding Wire 3 Inlet Wire Guide 4 Pressure Adjustment Knob 5 Drive Roll 6 Gun Cable Lay gun cable out straight. T ools Needed: 6 1 Pull and hold wire; cut off end. 4 in (102 mm) Remove gun nozzle and contact tip.
OM-947 Page 17 SECTION 5 − OPERATION 5-1. Controls 1 V oltage Switch Use control to select the weld voltage range. As the thickness of material increases, a higher voltage range must be selected (see weld setting label in welding power source or Section 5-3 as applicable).
OM-947 Page 18 5-3. W eld Parameter Chart.
OM-947 Page 19 210 428.
OM-947 Page 20 SECTION 6 − MAINTENANCE &TROUBLESHOOTING 6-1. Routine Maintenance Y Disconnect power before maintaining. 3 Months Replace unreadable labels. Repair or replace cracked weld cable. Clean and tighten weld terminals. 6 Months Blow out or vacuum inside.
OM-947 Page 21 6-4. Changing Drive Roll Or Wire Inlet Guide 1 Pressure Adjustment Knob 2 Pressure Assembly Pivot pressure adjustment knob down, and lift pressure assembly up. 3 Pivot T ube Plate 4 Securing Screws 5 Pressure Arm Pivot T ube 6 Inlet Wire Guide Remove screws and pivot tube plate.
OM-947 Page 22 6-5. Replacing Gun Contact Tip T ools Needed: Ref. 804 241-A Y T ur n off welding power source. 1 Nozzle Remove nozzle. 2 Contact T ip 3 Tip Adapter Cut off welding wire at contact tip. Remove contact tip from tip adapter , and install new contact tip.
OM-947 Page 23 6-6. Cleaning Gun Liner 804 241-A / 803 838-A Y T ur n off welding power source. 1 Nozzle 2 Contact T ip 3 Adapter Head T ube T ools Needed: 8 mm La y gun cable out straight, and blow out liner . Remove nozzle. Cut of f wire at contact tip, and remove contact tip and tip adapter .
OM-947 Page 24 6-7. Replacing Gun Liner Ref. 804 241-A / 803 497-A / 803 837-A / 803 899-A T ools Needed: 8 mm / 10 mm Remove nozzle. Cut of f wire at contact tip, and remove contact tip and tip adapter . Open pressure assembly. Retract wire from liner onto spool.
OM-947 Page 25 6-7. Replacing Gun Liner (Continued) When liner exits cable at gun handle, guide liner into head tube. Continue to push liner until it exits end of head tube. Slide locking rings over top and bottom of handle, and secure by twisting rings clockwise 1/4 turn.
OM-947 Page 26 6-8. T roubleshooting T able T rouble Remedy No weld output; wire does not feed; fan does not run Secure power cord plug in receptacle (see Section 4-6). d oes no t run. Replace building line fuse or reset circuit breaker if open. Place Power switch in On position (see Section 5-1).
OM-947 Page 27 SECTION 7 − ELECTRICAL DIAGRAM 230 950-A Figure 6-1. Circuit Diagram.
OM-947 Page 28 SECTION 8 − WIRE WELDING GUIDELINES 8-1. T ypical FCA W Process Connections Y W eld current can damage electronic parts in vehicles. Disconnect both battery cables before welding on a vehicle. Pla ce w or k cl am p as close to the weld as possible.
OM-947 Page 29 8-3. T ypical Control Settings These settings are guidelines only . Material and wire type, joint design, fitup, position, etc. affect settings. T est welds to be sure they comply to specifications. NOTE 3.5 x 125 A = 437 ipm 2 x 125 A = 250 ipm 1.
OM-947 Page 30 8-4. Holding And Positioning Welding Gun Welding wire is energized when gun trigger is pressed. Before lowering helmet and pressing trigger , be sure wire is no more than 1/2 in (13 mm) past end of nozzle, and tip of wire is positioned correctly on seam.
OM-947 Page 31 8-5. Conditions That Affect Weld Bead Shape Weld bead shape depends on gun angle, direction of travel, electrode extension (stickout), travel speed, thickness of base metal, wire feed speed (weld current), and voltage.
OM-947 Page 32 8-6. Gun Movement During Welding Normally , a single stringer bead is satisfactory for most narrow groove weld joints; however , for wide groove weld joints or bridging across gaps, a weave bead or multiple stringer beads works better .
OM-947 Page 33 8-9. T roubleshooting − Excessive Spatter Excessive Spatter − scattering of molten metal particles that cool to solid form near weld bead. S-0636 Possible Causes Corrective Actions Wire feed speed too high. Select lower wire feed speed.
OM-947 Page 34 8-12. T roubleshooting − Lack Of Penetration Lack Of Penetration − shallow fusion between weld metal and base metal. Lack of Penetration Good Penetration S-0638 Possible Causes Corrective Actions Improper joint preparation. Material too thick.
OM-947 Page 35 8-15. T roubleshooting − W aviness Of Bead W aviness Of Bead − weld metal that is not parallel and does not cover joint formed by base metal. S-0641 Possible Causes Corrective Actions W elding wire extends too far out of nozzle. Be sure welding wire extends not more than 1/2 in (13 mm) beyond nozzle.
OM-947 Page 36 SECTION 9 − P ARTS LIST . Hardware is common and not available unless listed. 803 446-B 1 2 3 4 5 6 6 7 8 9 10 11 12 13 14 15 16 17 18 19 42 20 21 22 23 24 25 26 27 28 29 32 30 31 33 34 35 36 37 38 39 40 41 43 Figure 8-1.
OM-947 Page 37 Description Part No. Dia. Mkgs. Item No. Figure 8-1. Main Assembly Quantity 1 210 432 CASE SECTION, front/bottom/rear 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 530 BLANK, snap-in 1 .
OM-947 Page 38 1 804 243-A 2 3 5 − See T able 8-1 4 6 7 7 Figure 8-2. H-9B Gun Description Part No. 225 397 Item No. Figure 8-2. H-9B Gun Quantity 1 169 715 NOZZLE, slip type .500 orf flush 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-947 Page 39 803 442-B 4 5 1 6 7 8 9 2 3 Figure 8-3. Wire Drive Assembly Quantity Description Part No. 209 532 Item No. Figure 8-3. Wire Drive Assembly 1 212 377 BEARING, idler 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notes.
Notes.
Notes.
Warranty Questions? Call 1-800-332-3281 7 AM − 6 PM EST hobart_warr 2006 − 01 Service Y o u always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours. Support Need fast answers to the tough welding questions? Contact your distributor or call 1-800-332-3281.
PRINTED IN USA © 2005 Hobart Welding Products. 6/05 Hoba rt We lding Product s An Illinois T ool W or ks Comp an y 600 W est Main Stree t Tr oy , OH 45373 USA For Technical Assi stance: Call1-800-332.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hobart Welding Products OM-947 212 149D è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hobart Welding Products OM-947 212 149D - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hobart Welding Products OM-947 212 149D imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hobart Welding Products OM-947 212 149D ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hobart Welding Products OM-947 212 149D, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hobart Welding Products OM-947 212 149D.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hobart Welding Products OM-947 212 149D. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hobart Welding Products OM-947 212 149D insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
