Manuale d’uso / di manutenzione del prodotto AM14C ML-32615 del fabbricante Hobart
Vai alla pagina of 20
MODEL AM14 & AM14C DISHWASHERS MODELS AM14 ML-32614 AM14C ML-32615 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 34123 Rev.
– 2 – POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED FROM THE LOCAL GAS SUPPLIER. IMPORT ANT IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN UNIT(S) AT MAIN SHUTOFF VALVE AND CONTACT THE LOCAL GAS COMPANY OR GAS SUPPLIER FOR SERVICE.
– 3 – TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– 4 – Installation, Operation, and Care of MODEL AM14 & AM14C DISHW ASHERS SA VE THESE INSTRUCTIONS GENERAL The AM14 dishwashers are semi-automatic rack-type machines. On model AM14, the doors open on opposite sides of the machine allowing the rack to move straight through.
– 5 – Available as an optional accessory is a frame-mounted 10KW electric booster to maintain a minimum final rinse temperature of 180 ° F. Also available as an optional accessory is the model IB57 Infrared Booster Gas Water Heater. Also available are circuit breaker(s) and/or single point electrical connection options.
– 6 – WATER REQUIREMENTS Proper water quality can improve ware washing performance by reducing spotting, lowering chemical supply costs, enhancing effectiveness of labor, and extending equipment life. Local water conditions vary from one location to another.
– 7 – With Electric Booster Water Heater The water supply line is connected to the booster (Fig. 6) with 3 / 4 " pipe. The water supply should have a minimum temperature of 120 ° F – 140 ° F, and a flowing pressure of 15 – 25 psig at the pressure gauge tee beside the solenoid valve.
– 8 – The dishwasher must be installed so that the flow of combustion and ventilation air will not be obstructed. Adequate clearances for air openings into the combustion chamber must be provided. Make sure there is an adequate supply of make-up air in the room to allow for combustion of the gas at the burner(s).
– 9 – RATE OF EXHAUST FLOW CALCULATIONS Based on the 1996 International Mechanical Code. The Rate of air flow required for a vent hood is calculated using the following definitions: Q = Rate of Air Flow in Cubic Feet Per Minute or [ CFM ] Required for the Hood.
– 10 – STEAM HEAT (When Specified) A 3 / 4 " union connection for the steam supply line is located at the lower right side of the machine. The steam supply must have a flowing pressure of 15 – 20 psig. Steam flow is controlled by a solenoid valve, as well as a mechanical ball valve.
– 11 – Electric Booster Water Heater Option NOTE : Electric Booster electrical connection will be separate from the dishwasher electrical connection unless single point electrical connection is supplied. If circuit breaker option is provided, the electric supply or supplies are connected to the circuit breaker box on top of the dishwasher.
– 12 – A T A D L A C I R T C E L EA T A D L A C I R T C E L E A T A D L A C I R T C E L E A T A D L A C I R T C E L EA T A D L A C I R T C E L E l e d o Ml e d o M l e d o M l e d o Ml e d o Mh P .
– 13 – OPERA TION PREPARATION Place the pump strainer (when equipped), overflow tube, overflow cover, end cover, slanted strainer, and the strainer bucket in their respective positions, (Fig. 7). Fig. 7 An automatic detergent dispenser is recommended.
– 14 – PL-40416-1 Reset Button Rinse T emperature Adjustment Screw DISHWASHING Scrape the dishes to remove large particles of food and debris. Never use steel wool on ware to be loaded into the dishmachine. Fig. 9 Stack the dishes in a rack. Do not stack dishes one on top of another as water must have free access to all sides of every dish.
– 15 – CLEANING T he machine must b e thoroughly cleaned at the end of each working shift or at least daily. Never use steel wool to clean warewasher surfaces. Use only products formulated to be safe on stainless steel. Turn off the power switch. If the machine has steam heat, close the manually operated steam ( ball) valve.
– 16 – DOs AND DON'Ts FOR YOUR NEW HOBART WAREWASHER DO assure proper water hardness (4 – 6 grains per gallon is recommended). DO pre-scrap dishes thoroughly. DO use only detergents recommended by your chemical professional. DO at the end of the day, thoroughly cleanse the machine, rinse, and dry (leave doors open).
– 17 – MAINTENANCE WARNING : DISCONNECT ELECTRICAL POWER SUPPLY (BOTH DISHWASHER AND BOOSTER IF APPLICABLE) AND PLACE A TAG(S) AT THE DISCONNECT SWITCH(ES) TO INDICATE THE CIRCUIT(S) ARE BEING WORKED ON BEFORE BEGINNING ANY MAINTENANCE PROCEDURE. WASH ARMS Upper and lower wash and rinse arms (Figs.
– 18 – To avoid a service call, check symptoms and related possible causes. If machine still does not operate properly, contact Service. SYMPTOM POSSIBLE CAUSE No machine operation. 1. Blown fuse or tripped circuit breaker at power supply. 2. Machine control is in MANUAL mode.
– 19 – SYMPTOM POSSIBLE CAUSE Inadequate rinse. 1. Dirty line strainer causing reduced water flow. Turn off water supply, remove strainer cap, withdraw and clean screen. Reassemble. 2. Low supply line pressure. 3. Excessive mineral deposits throughout wash and rinse system.
– 20 – SERVICE Contact your local Hobart-authorized service office for any repairs or adjustments needed on this equipment. If a gas orifice fitting is to be adjusted or replaced, have it serviced by qualified Hobart- authorized service personnel.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hobart AM14C ML-32615 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hobart AM14C ML-32615 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hobart AM14C ML-32615 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hobart AM14C ML-32615 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hobart AM14C ML-32615, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hobart AM14C ML-32615.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hobart AM14C ML-32615. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hobart AM14C ML-32615 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
