Manuale d’uso / di manutenzione del prodotto CP-X600 del fabbricante Hitachi
Vai alla pagina of 64
1 Projector CP-X600 User's Manual – Oper ating Guide Thank you for purchasing this projector . WARNING ► Before using this product, please read the "User's Manual - Safety Guide" and related manuals to ensure the proper use of this product.
2 About this manual . . . . . . . . . . 1 C o n t e n t .................. 2 Projector features . . . . . . . . . . 3 Prepar ations . . . . . . . . . . . . . . 3 Contents of package . . . . . . . . . . . . .3 Fastening the lens cover . . . . . . . . .
3 F astening the lens co ver T o avoid losing the lens cover , please fasten the lens cover to the projector using the included strap. 1. Fix the strap to the strap hole of the lens cover . 2. Put one side of the strap into the groove on the rivet. 3.
4 Par t names Part names Projector (1) Speakers (x 4) ( 36 ). (2) Focus ring ( 18 ) (3) Zoom ring ( 18 ) (4) Lamp cover ( 52 ) The lamp unit is inside.
5 Par t names Control panel (1) ST ANDBY/ON button ( 15 ) (2) MENU button ( 22 ) It consists of four cursor buttons. (3) INPUT button ( 16 ) (4) POWER indicator ( 15, 58 ) (5) TEMP ind.
6 Par t names WARNING ►Do not look into the beam outlet and point the beam at people and pets while pressing the LASER button, since the beam is not good for eyes. CA UTION ►Note that the laser beam may result in hazardous radiation exposure. U se the lase r pointer only for pointing on the screen.
7 Setting up Setting up Install the projector according to the environment and manner the projector will be used in. WARNING ► Place the projector in a stable horizontal position. If the projector falls or is knocked over it could cause injury and/or damage to the projector .
8 Ar rangement Refer to the illustrations and tables below to determine screen size and projection distance. The values shown in the table are calculated for a full size screen: 1024×768 (a) Screen s.
9 Adjusting the projector's eleva tor When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally . Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of the projector within 8 degrees.
10 Setting up Connecting your de vices Be sure to read the manuals for devices before connecting them to the projector . Make sure that all the devices are suitable to be connected with this product, and prepare the cables required to connect. Please refer to the following illustrations to connect them.
1 1 Setting up NOTE • Be sure to read the manuals for devices before connecting them to the projector , and make sure that all the devices are suitable to be connected with this product. Before connecting to a PC, check the signal level, the signal timing, and the resolution.
12 Setting up Connecting pow er suppl y 1. Connect the connector of the power cord to the AC inlet of the projector . 2. Firmly plug the power cord's plug into the outlet. WARNING ► Please use extra caution when connecting the power cord, as incorrect or faulty connections may result in re and/or electrical shock.
13 Remote control Putting batteries Please load the batteries before using the remote control. If the remote control starts to malfunction, replace the batteries. If you will not use the remote control for an extended period, remove the batteries from the remote control and store them in a safe place.
14 About the remote contr ol signal The remote control works with the projector ’s remote sensors. This projector has three remote sensors on the front, on the top, and on the back. The sensors can be respectively turned active or inactive using the “REMOTE RECEIV” in the SERVICE item of OPTION menu ( 46 ).
15 Po wer on/of f T ur ning on the power 1. Make sure that the power cord is rmly and correctly connected to the projector and the outlet. 2. Remove the lens cover , and set the power switch to the ON position. The power indicator will light up in steady orange ( 58 ).
16 Operating Operating Adjusting the v olume 1. Press the VOLUME button on the remote control. A dialog will appear on the screen to aid you in adjusting the volume. 2. Use the cursor buttons ▲/▼ to adjust the volume. T o close the dialog and complete the operation, press the VOLUME button again.
17 Operating Searching an input signal 1. Press the SEARCH button on the remote control. The projector will start to check its input ports in order to nd any input signals. When an input is found, the projector will stop searching and display the image.
18 Adjusting the zoom and f ocus 1. Use the zoom ring to adjust the screen size. 2. Use the focus ring to focus the picture. Operating Focus ring Zoom ring Using the automatic adjustment f eature 1.
19 Adjusting the position 1. Press the POSITION button on the remote control. The “POSITION” indication will appear on the screen. 2. Use the cursor buttons ▲/▼/◄/► to adjust the picture position. When you want to reset the operation, press the RESET button on the remote control during the operation.
20 Operating Using the magnify feature 1. Press the ON button of MAGNIFY on the remote control. The “MAGNIFY” indication will appear on the screen (although the indication will disappear in several seconds with no operation), and the projector will go into the MAGNIFY mode.
21 Operating T empor aril y blanking the scr een 1. Press the BLANK button on the remote control. The blank screen will be displayed instead of the screen of input signal. Please refer to the BLANK item in SCREEN menu ( 37 ). T o exit from the blank screen and return to the input signal screen, press the BLANK button again.
22 Operating Using the menu function This projector has the following menus: PICTURE, IMAGE, INPUT , SETUP , AUDIO, SCREEN, OPTION, and EASY MENU. EASY MENU consists of functions often used, and the other menus are classied into each purpose. Each of these menus is operated using the same methods.
23 EASY Menu EASY Menu Item Description ASPECT Using the ◄/► buttons switches the mode for aspect ratio. See the ASPECT item in IMAGE menu ( 28 ). AUTO KEYSTONE EXECUTE Using the ► button executes the auto keystone function. See the AUTO KEYST ONE EXECUTE item in SETUP menu ( 34 ).
24 EASY Menu Item Description BRIGHTNESS Using the ◄/► buttons adjusts the brightness. See the BRIGHTNESS item in PICTURE menu ( 25 ). CONTRAST Using the ◄/► buttons adjusts the contrast. See the CONTRAST item in PICTURE menu ( 25 ). COLOR Using the ◄/► buttons adjusts the strength of whole color .
25 PICTURE Menu PICTURE Menu Item Description BRIGHTNESS Using the ▲/▼ buttons adjusts the brightness. Light ó Dark CONTRAST Using the ▲/▼ buttons adjusts the contrast.
26 Item Description COLOR TEMP Using the ▲/▼ buttons switches the color temperature mode. T o adjust CUSTOM Selecting a mode whose name includes CUSTOM and then pressing the ► button or the ENTER button displays a dialog to aid you in adjusting the OFFSET and GAIN of the selected mode.
27 PICTURE Menu Item Description ACTIVE IRIS Using the ▲/▼ cursor buttons changes the active iris control mode. PRESENT A TION ó THEA TER ó TURN OFF Feature PRESENT A TION The active iris displays the best presentation image for both bright and dark scenes.
28 IMAGE Menu IMAGE Menu Item Description ASPECT Using the ▲/▼ buttons switches the mode for aspect ratio. For an RGB signal NORMAL ó 4:3 ó 16:9 ó SMALL For a Video signal, S-video signal or Component video signal 4:3 ó 16:9 ó 14:9 ó SMALL For no signal 4:3 (xed) • The NORMAL mode keeps the original aspect ratio of the signal.
29 IMAGE Menu Item Description H PHASE Using the ▲/▼ buttons adjusts the horizontal phase to eliminate icker . Right ó Left • This item can be selected only for an RGB signal or a component video signal. (except 525i (480i), 625i (576i), SCART RGB) H SIZE Using the ▲/▼ buttons adjusts the horizontal size.
30 INPUT Menu INPUT Menu Item Description PROGRESSIVE Using the ▲/▼ buttons switches the progress mode. TV ó FILM ó TURN OFF • This function is performed only for an interlaced signal of a VIDEO input, an S-VIDEO input or COMPONENT VIDEO input of 525i (480i), 625i (576i) or 1 125i (1080i) signal.
31 Item Description COMPONENT Using the ▲/▼ buttons switches the function of the COMPONENT (Y , C b /P b , C r /P r ) port. COMPONENT ó SCAR T RGB When the SCART RGB is selected, the COMPONENT (Y , C b /P b , C r /P r ) and VIDEO ports will function as a SCART RGB port.
32 Item Description FRAME LOCK Using the ▲/▼ buttons turns the frame lock function on/off. TURN ON ó TURN OFF • This item can be performed only on an RGB signal with a vertical frequency of 50 to 60 Hz. • When the TURN ON is selected, a moving pictures are displayed more smoothly .
33 INPUT Menu Item Description RESOLUTION The resolution for the RGB1 and RGB2 input signals can be set on this projector . (1) In the INPUT menu select the RESOLUTION using the ▲/▼ buttons and press the ► button. The RESOLUTION menu will be displayed.
34 SETUP Menu SETUP Menu Item Description AUTO KEYSTONE EXECUTE Selecting this item performs the Automatic keystone distortion correction. Projector automatically corrects vertical keystone distortion due to the (forward/backward) setup angle by itself.
35 SETUP Menu SETUP Menu (continued) Item Description WHISPER Using the ▲/▼ buttons turns off/on the whisper mode. NORMAL ó WHISPER • When the WHISPER is selected, acoustic noise and screen brightness are reduced. MIRROR Using the ▲/▼ buttons switches the mode for mirror status.
36 A UDIO Menu AUDIO Menu Item Description VOLUME Using the ▲/▼ buttons adjusts the volume. High ó Low SPEAKER Using the ▲/▼ buttons turns the speaker function on/off. TURN ON ó TURN OFF • When the TURN ON is selected the built-in speaker works.
37 SCREEN Menu SCREEN Menu Item Description LANGUAGE Using the ▲/▼ buttons switches the OSD (On Screen Display) language. SUOMI ó POLSKI ó TÜRKÇE ENGLISH ó FRANÇAIS ó DEUTSCH ó ESP AÑOL .
38 SCREEN Menu Item Description ST ART UP Using the ▲/▼ buttons switches the mode for the start-up screen. The start-up screen is a screen displayed when no signal or an unsuitable signal is detected. MyScreen ó ORIGINAL ó TURN OFF Feature MyScreen Screen can be registered by the MyScreen item ( 39 ) .
39 SCREEN Menu Item Description MyScreen This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and ST ART UP screen. Display the image you want to capture before executing the following procedure. 1.
40 SCREEN Menu Item Description MESSAGE Using the ▲/▼ buttons turns on/off the message function. TURN ON ó TURN OFF When the TURN ON is selected, the following message function works. “AUTO IN PROGRESS” while automatically adjusting “NO INPUT IS DETECTED” “SYNC IS OUT OF RANGE” “Searching….
41 OPTION Menu OPTION Menu Item Description AUTO SEARCH Using the ▲/ ▼ buttons t urns on/of f the automatic signa l search fun ction. TURN ON ó TURN OFF When the TURN ON is selected, detecting no signal automatically cycles through input ports in the following order .
42 Item Description AUTO OFF Using the ▲/▼ buttons adjusts the time to count down to automatically turn the projector off. Long (max. 99 minutes) ó Short (min. 0 minute = DISABLE) AUTO OFF ENABLE 1 AUTO OFF DISABLE 0 When th e time i s set t o 0, the projec tor is n ot turn ed of f automaticall y .
43 Item Description MY BUTT ON This item is to assign one of the following function to MY BUTT ON 1 and 2 on the remote control ( 6 ). Choose 1 or 2 on the MY BUTT ON menu using the ◄/► button rst. Then using the ▲/▼ buttons se ts one of the f ollowing functi ons to the chosen button.
44 Item Description SERVICE AUTO ADJUST Using the ▲/▼ buttons enables/disables the automatic adjustment.When DISABLE is selected, the automatic adjustment feature is disabled, although rough adjustment is automatically performed depending on the basic setting.
45 Item Description SERVICE KEY LOCK Using the ▲/▼ buttons turns on/off the key lock feature. When TURN ON is selected, the buttons on the projector except the ST ANDBY/ON button are locked. TURN ON ó TURN OFF • Please use to avoid a mischief and touching accidentally .
46 Item Description SECURITY This projector is equipped with security functions. User registration is required before using the security functions. Please contact your local dealer . 1. Using Security Features 1.1 Inputting the P ASSWORD 1.1-1 Use the ▲/▼ buttons on the OPTION menu to select SECURITY and press the ► button.
47 Item Description SECURITY 1.3 If you have forgotten your P ASSWORD 1.3-1 Follow the procedure in 1.1-1 to display the ENTER P ASSWORD BOX. 1.3-2 While the ENTER P ASSWORD BOX is displayed, press and hold the RESET button on the remote control for about 3 seconds or press and hold the INPUT and ► buttons on the projector for about 3 seconds.
48 Item Description SECURITY 2.2-4 Move the cursor to the right side of the CHECK P ASSWORD BOX and press the ► button to display the P ASSWORD for about 20 seconds, please make note of the P ASSWORD during this time. Pressing the ENTER button on the remote control or INPUT button on the projector will return to MyScreen P ASS WORD on/off menu.
49 Item Description SECURITY 3.1-3 Input a 4 part PIN Code using the ▲/▼/◄/► /RGB and INPUT buttons. A CONFIRMA TION BOX will appear . Reenter the same PIN Code. This will complete the PIN Code registration. NOTE: If there is no key input for about 55 seconds while the PIN BOX or the CONFIRM A TION BOX are displayed the menu will close.
50 Item Description SECURITY 4. Using the T ransition Detector Function While the T ransition Detector function is ON, when power switch is started to supply to the projector , it might react as below . • T ransition Detector alarm shown below might appear on screen, if the projector has been moved or re-installed.
51 Item Description SECURITY 4.3 Setting the T ransition Detector off 4.3-1 Follow the procedure in 4.1-1 to display the T ransition Detector on/off menu. 4.3-2 Select TURN OFF to display the ENTER P ASSWORD BOX (large). Enter the registered P ASSWORD and the screen will return to the T ransition Detector on/off menu.
52 Maintenance Lamp A lamp has nite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor . Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
53 Maintenance Lamp (continued) WARNING HIGH VOL T AGE HIGH TEMPERA TURE HIGH PRESSURE ► The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.
54 Please check and clean the air lter periodically . If the air lter becomes clogged by dust or the like, internal temperatures rise, which could cause a re, a burn or malfunction to the projector . When the indicators or a message prompts you to clean the air lter , comply with it as soon as possible.
55 WARNING ►Before taking care of the air lter , make sure the power switch is off and the power cable is not plugged in, then allow the projector to cool sufciently . T aking care of the air lter in a high temperature state of the projector could cause an electric shock, a burn or malfunction to the projector .
56 Maintenance Inside of the projector In order to ensure the safe use of your projector , please have it cleaned and inspected by your dealer about once every year . Caring for the lens If the lens is awed, soiled or fogged, it could cause deterioration of display quality .
57 T roubleshooting R elated messages When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please follow the instructions described below .
58 T r oubleshooting R e gar ding the indicator lamps Lighting and ashing of the POWER indicator , the LAMP indicator , and the TEMP indicator have the meanings as described in the table below .
59 T r oubleshooting Regarding the indicator lamps (continued) POWER indicator LAMP indicator TEMP indicator Description Blinking In Red or Lighting In Red T urned off Blinking In Red The cooling fan is not operating. Please turn the power off, and allow the projector to cool down at least 20 minutes.
60 T r oubleshooting Phenomena that may be easy to be mistak en for mac hine defects WARNING ► Never use the projector if abnormal operations such as smoke, strange odor , excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter , etc.
61 Pheno mena that may be e asy to be mis taken for mach ine defec ts ( conti nued ) Phenomenon Cases not involving a machine defect Reference page Sound does not come out. The signal cables are not correctly connected. Correctly connect the audio cables.
62 Pheno mena that may be e asy to be mis taken for mach ine defec ts ( conti nued ) Phenomenon Cases not involving a machine defect Reference page Pictures appear dark. The brightness and/or contrast are adjusted to an extremely low level. Adjust BRIGHTNESS and/or CONTRAST settings to a higher level using the menu function.
63 Warr anty And After-Ser vice / Specication W arranty and after-service If a problem occurs with the equipment, rst refer to the “T roubleshooting” and run through the suggested checks. If this does not resolve the problem, please contact your dealer or service company .
64 Specications Specications (continued) 418 319 154 139 [unit: mm].
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hitachi CP-X600 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hitachi CP-X600 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hitachi CP-X600 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hitachi CP-X600 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hitachi CP-X600, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hitachi CP-X600.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hitachi CP-X600. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hitachi CP-X600 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
