Manuale d’uso / di manutenzione del prodotto CP-X3014WN del fabbricante Hitachi
Vai alla pagina of 32
1 Projector CP-X2514WN/CP-X3014WN/ CP-X4014WN/CP-WX3014WN User's Manual (detailed) Oper a ting Guide – T ec hnical Resolution (H x V) H. frequency (kHz) V . frequency (Hz) Rating Signal mode 720 x 400 37.9 85.0 VESA TEXT 640 x 480 31.5 59.9 VESA VGA (60Hz) 640 x 480 37.
2 Initial set signals Back porch (B) Front porch (D) Back porch (b) Front porch (d) Active video (C) Data Data H. Sync. V . Sync. Sync (A) Sync (a) Active video (c) Resolution (H x V) Horizontal signal timing (μs) V ertical signal timing (lines) Signal mode (A) (B) (C) (D) (a) (b) (c) (d) 720 x 400 2.
3 A COMPUTER IN1, B COMPUTER IN2, C MONIT OR OUT D-sub 15pin mini shrink jack <Computer signal> • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V . sync. signal: TTL level (positive/negative) • Composite sync.
4 G S-VIDEO Mini DIN 4pin jack • System: NTSC, P AL, SECAM, P AL-M, P AL-N, NTSC4.43, P AL(60Hz) Pin Signal 1 Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator Color signal 0.
5 Connection to the por ts (continued) J AUDIO IN1, K AUDIO IN2 Ø3.5 stereo mini jack • 200 mV rms 47kΩ terminator AUDIO IN3 L R, M L AUDIO OUT N R, O L RCA jack x2 RCA jack x2 • 200 mV rms 47kΩ terminator • 200 mV rms 1kΩ output impedance P MIC Ø3.
6 Connection to the por ts (continued) R USB TYPE B USB B type jack Pin Signal 1 +5V 2 - Data 3 + Data 4 Ground S CONTROL D-sub 9pin plug • About the details of RS-232C communication, please refer to the following page.
7 T o input SCART RGB signal; ex. 㪭㫀㪻㪼㫆 㪩 㪙 㪞 㪘㫌㪻㫀㫆㩷㪣 㪘㫌㪻㫀㫆㩷㪩 Connection to the por ts (continued) T o input SCART RGB signal to the projector , use a SCART to RCA cable. Connect the plugs refer to above ex.
8 ①② ⑥⑦⑧⑨ ⑤ ④ ③ CD (1) (1) − RD(2) (2) RD TD (3) (3) TD DTR (4) (4) − GND (5) (5) GND DSR (6) (6) − RTS (7) (7) R TS DTS (8) (8) CTS RI (9) (9) − RS-232C Communication RS-232.
9 RS-232C Communication (continued) Communicaion settings 1. Pr otocol 19200bps,8N1 2. Command for mat ("h" shows hexadecimal) Byte Number 01 2 3 4 5 6 78 9 1 0 1 1 1 2 Command Action Header.
10 RS-232C Communication (continued) 3. R esponse code / Er ror code ("h" shows hexadecimal) (1) ACK reply : 06h When the projector receives the Set, Increment, Decrement or Execute command correctly , the projector changes the setting data for the specified item by [T ype], and it returns the code.
11 When the projector connects network, the projector can be controlled with RS- 232C commands from the computer with web browser . For details of RS-232C commands, refer to RS-232C Communication / Network command table ( 17 ). Command Control via the Networ k LAN cable (CAT-5 or greater) LAN LAN Connection 1.
12 Communicaion P or t The following two ports are assigned for the command control. TCP #23 TCP #9715 Configure the following items form a web browser when command control is used. Port Settings Network Control Port1 (Port: 23) Port open Click the [Enable] check box to open [Network Control Port1 (Port: 23)] to use TCP #23.
13 Command Control via the Networ k (continued) Command contr ol settings [TCP #23] 1. Command for mat Same as RS-232C communication, refer to RS-232C Communicaton command format. 2. R esponse code / Er ror code ("h" shows hexadecimal) Four of the response / error code used for TCP#23 are the same as RS-232C Communication (1)~(4).
14 2. R esponse code / Er ror code ("h" shows hexadecimal) The connection ID is attached for the TCP#23's response / error codes are used.
15 This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by wired or wireles LAN communicaton, an external device that is connected with this projector by RS- 232C communication can be controlled from the computer as a network terminal.
16 Communica tion settings For communication setting, use the OPTION - SER VICE - COMMUNICA TION menu. ( OPTION menu - SERVICE - COMMUNICA TION in the Operating Guide ) Item Condition BAUD RA TE 4.
17 RS-232C Communication / Network command table Names Operation T ype Header Command Data CRC Action T ype Setting code Power Set T urn off BE EF 03 06 00 2A D3 01 00 00 60 00 00 T urn on BE EF 03 06.
RS-232C Communication / Netw or k command table (continued) 18 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code BRIGHTNESS Get BE EF 03 06 00 89 D2 02 0.
RS-232C Communication / Netw or k command table (continued) 19 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code User Gamma Point 5 Reset Execute BE EF 0.
RS-232C Communication / Netw or k command table (continued) 20 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code COLOR TEMP OFFSET R Reset Execute BE EF .
RS-232C Communication / Netw or k command table (continued) 21 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code OVER SCAN Get BE EF 03 06 00 91 70 02 00.
RS-232C Communication / Netw or k command table (continued) 22 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code C-VIDEO FORMA T Set AUTO BE EF 03 06 00 .
RS-232C Communication / Netw or k command table (continued) 23 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code ST ANDBY MODE Set NORMAL BE EF 03 06 00 .
RS-232C Communication / Netw or k command table (continued) 24 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code VOLUME - S-VIDEO Get BE EF 03 06 00 75 C.
RS-232C Communication / Netw or k command table (continued) 25 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code AUDIO SOURCE - USB TYPE A Set AUDIO IN1 .
RS-232C Communication / Netw or k command table (continued) 26 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code MIC LEVEL Set LOW BE EF 03 06 00 02 F1 0.
RS-232C Communication / Netw or k command table (continued) 27 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code MENU POSITION V Reset Execute BE EF 03 0.
RS-232C Communication / Netw or k command table (continued) 28 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code RS-232C Communication / Netw or k comman.
RS-232C Communication / Netw or k command table (continued) 29 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code RS-232C Communication / Netw or k comman.
RS-232C Communication / Netw or k command table (continued) 30 (continued on next page) Names Operation T ype Header Command Data CRC Action T ype Setting code MY IMAGE Set OFF BE EF 03 06 00 3A C3 01.
31 PJLink command PJLink command POWR Power Contorol 0 = Standby 1 = Power On POWR ? Power Status inquiry 0 = Standby 1 = Power On 2 = Cool Down INPT Input Source selection 1 1 = COMPUTER IN 1 12 = CO.
32 PJLink command (continued) Commands Control Description Parameter or Response ERST ? Error Status inquiry 1st byte: Refers to Fan error; one of 0 to 2 2nd byte: Refers to Lamp error; one of 0 to 2 .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hitachi CP-X3014WN è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hitachi CP-X3014WN - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hitachi CP-X3014WN imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hitachi CP-X3014WN ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hitachi CP-X3014WN, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hitachi CP-X3014WN.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hitachi CP-X3014WN. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hitachi CP-X3014WN insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
