Manuale d’uso / di manutenzione del prodotto DS-2CD4065F-A del fabbricante Hikvision
Vai alla pagina of 134
Network Camera User Manual V5.2.0 UD.6L0201D1514A 01.
User Manual of Network Camera 1 Thank you for purchasing our pr oduct. If there are any questions, or requ ests, please do not hesitate to contact the dealer.
User Manual of Network Camera 2 This manual may contai n several te chnical incorr ect places or printing errors, and the content is subject to change without notice. Th e updates will be added to the new version of this manual. W e will readily improve or update the products or procedure s described in the manual.
User Manual of Network Camera 3 Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to compl y with the limits for a digital device, pursuant to part 15 of the FCC Rules.
User Manual of Network Camera 4 Safety Instruction These instructions are intended to ensure that the user can us e the prod uct correctly t o avoid danger or property loss. The precaution measure is divided into ‘W arning s’ and ‘Cautions’: W arnings : Serious injury or death ma y be caused if an y of these warnings are neglected.
User Manual of Network Camera 5 Cautions: Make sure the power suppl y voltag e is correct before using the camera. Do not drop the camera or subject it to physical shock. Do not touch sensor modules with fingers. I f cleaning is necessary , use a c lean cloth with a bit of ethano l and wipe it gently .
User Manual of Network Camera 6 T able of Contents Chapter 1 System R equir ement .................................................................................. 9 Chapter 2 Network Connection .......................................................
User Manual of Network Camera 7 6.3.9 Email Sending T riggered by A larm ................................................................................ 48 6.3.10 Con figuring NA T (Network Address T ranslation) Settings .............................
User Manual of Network Camera 8 Chapter 1 1 Others ................................................................................................ 1 17 1 1.1 Managing User Accounts .....................................................................
User Manual of Network Camera 9 Chapter 1 System Requir ement Operating System: Microsoft W indows XP SP1 and above version / V ista / W in7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.
User Manual of Network Camera 10 Chapter 2 Network Connection Befor e you start: If y ou want to set the network camera via a LAN ( Local Are a Network), please refer to Section 2.1 Setting the Network Camera over the LAN . If y ou want to set the network camera via a W AN (Wide Area Network), please refer to Section 2.
User Manual of Network Camera 11 Figure 2-2 Connecting via a Switch or a Router 2.1.2 Detec ting and Changing the IP Addre ss You need the IP address to visit the network camera.
User Manual of Network Camera 12 Figure 2-3 SADP I nterface 2.2 Setting the Network Camera over the W AN Purpose: This section explains how to connect the network camera to the W AN with a static IP or a dynamic IP . 2.2.1 S tatic IP Connection Befor e you start: Please appl y a static IP from an ISP (Internet Service P rovider).
User Manual of Network Camera 13 2. Assign a LAN IP address, the subnet mask and the gateway . Refer to S ection 2.1.2 Detecting an d Changing the IP Address for detailed I P address c onfiguration of the camera. 3. Save the static IP in the router . 4.
User Manual of Network Camera 14 1. Connect the network camera to the router . 2. In the camera, assi gn a LAN IP address, the subnet mask and the gateway . R efer to Section 2.1.2 De tecting and Ch anging the IP Address for detailed LAN configuration.
User Manual of Network Camera 15 Figure 2-7 Normal Domain Name Resolution S teps: 1. Apply a domain name from a domain name provider . 2. Configure the DDNS sett ings in the DDNS Set tings interface of the network camera. Refer to Section 6.3.4 Configuring DDNS Settings for detailed configuration.
User Manual of Network Camera 16 Chapter 3 Access to the Netw ork Camera 3.1 Accessing by W eb Br o wsers Steps: 1. Open the web browser. 2. Input the IP address of the network camera in the address bar, e.g., 192.0.0.64 and press the Enter key to enter the login interface.
User Manual of Network Camera 17 Figure 3-2 Download and Install Plug- in Figure 3-3 Install Plug-in (1) Figure 3-4 Install Plug-in (2) Note: You may have to close the web browser to install the plug-in. Please reopen the web browser and log in again after installing the plug-in.
User Manual of Network Camera 18 3.2 Accessing by Client Softwar e The product CD contains the iVMS-4200 client software . Y ou can view the live video and manage the camera with the software. Follow the installation prompts to install the software. The control panel and live view interface of iVMS-4200 client software are shown as bellow.
User Manual of Network Camera 19 Figure 3-6 iVMS-4200 Configuration Panel Note: For detailed information about the software, please refer to the user manual of the iVMS-4200.
User Manual of Network Camera 20 Chapter 4 Wi -Fi Set tings Purpose: By conne cting to the wireless network, you don ’t need to use cable of an y kind for network connection, which is very c onvenient for the actual surveillance application. Note: This chapter is only applicable for the cameras with the built -in Wi -Fi module.
User Manual of Network Camera 21 4. Check the checkbox to select the Network mode as Manage, and the Security mode of the network is automatically shown when you select the wireless network, please don’ t change it manuall y . Note: These parameters a re exactly identical with those of the r oute r .
User Manual of Network Camera 22 Figure 4-5 Ad -hoc Connection Point 6. Choose the SSID and connect. Security Mode Description: Figure 4-6 Security Mode Y ou can choose the Securit y Mod e as not-encr ypted, WEP , WP A-personal, WP A-e nterprise, WP A2-personal, and W P A2-enterprise.
User Manual of Network Camera 23 the method used by y o ur access point. Not all acce ss points h ave this opti on, in which case the y probably us e Open S ystem, whi ch is sometimes known as SS I D Authentication. Key length - This sets th e len gth of the ke y used for the wireless encryption, 64 or 128 bit.
User Manual of Network Camera 24 Figure 4-9 EAP-TLS Identity - Enter the user ID to present to the network. Private key password – Enter the password for your user ID. EAPOL version - Select the version used (1 or 2) in your access point.
User Manual of Network Camera 25 WPS (W i-Fi Protected Setup) refers to the easy configuration of the e n crypted connection between the device and the wireless router . Th e WPS makes it easy to add new devices to an existing ne twork without entering long passphrases.
User Manual of Network Camera 26 4. Push the WPS button to enable the fun ction on the camera. If ther e is not a WP S button on the c ame ra, y ou can also c li ck the virtual button to enable the PBC function on the web interface. 5. Click Conn ect button.
User Manual of Network Camera 27 3. Click Conn ect . Or Y ou can generate the PIN code on the camera si de. And the ex pired time for the P IN code is 120 seconds. 1. Click Generate . 2. Enter the code to the router , in the example, enter 48167581 to the router .
User Manual of Network Camera 28 Chapter 5 Live V ie w 5.1 Live V iew Page Purpose: The live view page allows you to view the real-time video, capture images, realize PTZ control, set/call presets and configure video parameters.
User Manual of Network Camera 29 Click each tab to adjust the layout and the stream type of the live vi ew . And you can click the drop -down t o select the plu g-in.
User Manual of Network Camera 30 Live view with the third stream. Click to select the third-party plug- in . Manually capture the picture. / Manually start/stop recording. / Audio on and adjust volume /Mute. / Turn on/off microphone. / Turn on/off 3D zooming function.
User Manual of Network Camera 31 Figure 5-3 PTZ Control Panel Click the zoom/iris/focus buttons to realize lens control. Notes : There are 8 dir ection arr ows ( , , , , , , , ) in the live view window when you click and drag the mouse in the relative positions.
User Manual of Network Camera 32 2. Use the PT Z control buttons to move the lens to the desired position. • Pan the camera to the right or left. • Tilt the camera up or down. • Zoom in or out. • Refocus the lens. 3. C lick to finish the setting of the current preset.
User Manual of Network Camera 33 1. C lick to enter the patrol configuration interface. 2. S elect a path No., and click to add the configured presets. 3. S elect the preset, and input the patrol duration and patrol speed. 4. C lick OK to save the first preset.
User Manual of Network Camera 34 Chapter 6 Network Camera Configuration 6.1 Configuring Local Parameters Note: The local configuration refers to the parameters of the live vi ew , record files and captured pictures.
User Manual of Network Camera 35 streaming under some network environments. MUL TICAST : It’ s recommended to select MCAST type wh en using the Multicast function.
User Manual of Network Camera 36 6.2 Configuring Time Settings Purpose: Y ou can follow the instructions in this section to configure the time synchronization and DST setti ngs.
User Manual of Network Camera 37 Figure 6-3 T ime Sync by NTP S erver Note : If the camera is connected to a public network, y ou should use a NTP server that has a time s ynchronization function, such as the s erver at the National T im e Center (IP Address: 210.
User Manual of Network Camera 38 6.3 Configuring Network Settings 6.3.1 Configuring TCP/IP Settings Purpose: TCP/IP settings must be properly configured before you ope r ate the camera over network.
User Manual of Network Camera 39 and Multicast Address. Notes : The valid value range of MTU is 500 ~ 1500. The Multicast sends a stream to the multicast group address and allows multiple clients to acquire the stream at the same time by requesting a cop y from the multicast group address.
User Manual of Network Camera 40 HTTPS Port: The default port number is 443, and it can be changed to any port No. which is not occupied. Server Port: The default server port number is 8000, and it ca n be changed to any port No. ranges from 2000 to 65535.
User Manual of Network Camera 41 Registration on the DDNS server is required before configuring the DDNS settings of the camera. S teps: 1. Enter the DDNS Settings interface: Configuration > Advanced Configuration > Network > DDNS Figure 6-9 DDNS Settings 2.
User Manual of Network Camera 42 Figure 6-10 DynDNS Settings IP Server: Steps: (1) Enter the Server Address of the IP Server. (2) Click Save to save the settings. Note: For the IP Server, you have to apply a static IP, subnet mask, gateway and preferred DNS from the ISP.
User Manual of Network Camera 43 Figure 6-12 NO -IP Settings (2) Enter the Server Address as www.noip.com (3) Enter the Domain name you registered. (4) Enter the Port number, if needed. (5) Enter the User Name and Password. (6) Cli ck Save and then you can view the camera with the domain name.
User Manual of Network Camera 44 6.3.5 Configuring SNMP Settings Purpose: You can set th e SNMP function to get camera status, parameters and alarm related information and manage the camera remotely when it is connected to the network.
User Manual of Network Camera 45 Figure 6-14 SNMP Settings 2. C heck the corresponding version checkbox ( , , ) to enable the feature. 3. C onfigure the SNMP settings. Note: The settings of the SNMP software should be the sa me as the settings you configure here.
User Manual of Network Camera 46 6.3.6 Configuring 802.1X Settings Purpose: The IEEE 802.1X standard is supported b y the network cameras, and when the feature is enabled, the camera data is secured and u ser auth entication is needed when connecting the camera to the network protected by the IEEE 802.
User Manual of Network Camera 47 6.3.7 Configuring QoS Settings Purpose: QoS (Quality of S ervice) can help solve the network del a y and network congestion b y configuring the priority of data sending. S teps: 1. Enter the QoS Settings interface: Configuration >Advanced Configuration > Network > QoS Figure 6-16 QoS Settings 2.
User Manual of Network Camera 48 and the camera is connected to the Wide Ar e a Network via the router . S teps: 1. Enter the UPnP™ settings interface. Configuration >Advanced Configuration > Network > UPnP 2. Check the checkbox to enable the UPnP™ function.
User Manual of Network Camera 49 Figure 6-18 Email Settings 3. Configure the following settings: Sender: The name of the email sender . Sender’ s Add r ess: The email address of the se nd er . SMTP Server: The S MTP Server IP address or host name (e.
User Manual of Network Camera 50 Authentication (optional): If your email server requires authentication, check this checkbox to use authentication to log in to this server and enter th e login user Name and password. Choose Receiver: Select the receiver to which the email is sent.
User Manual of Network Camera 51 6.3.11 Configu ring FTP Settin gs Purpose: Y ou can configure the FTP server re l ated information to e nable the uploading of th e captured pictures to the FTP server . The captured pictures can be trigger ed by events or a timing snapshot task.
User Manual of Network Camera 52 3. Click Save to save the settings. Note : If you w ant to upload the captured pictures to FTP server , you have to enable the continuous snapshot or ev ent-triggered snapshot on Snapshot page. For detailed information, please refer to the Section 6.
User Manual of Network Camera 53 Configuration > Advanced Configu ration > Network > HTTPS 2. Create the self-signed certificate or authorized certificate. Figure 6-22 HTTPS Settings Create the self-signed certificate 1) Click Create button to enter the creation interface.
User Manual of Network Camera 54 Note: If y ou a lready h ad a certificate inst alled, the Create Self-signed Ce rtificate is gr a yed out. Create the authorized certificate 1) Click Create button to create the certificate request. 2) Download the certificat e request and submit it to the trusted certificate authority for signature.
User Manual of Network Camera 55 Figure 6-25 Configure V ideo Settings 2. Select the S tream T ype of the camera to main str eam (normal), sub -stream or third stream. The main strea m is usuall y for recording and live viewin g with g ood bandwidth, and the sub-stream and third stream can b e u sed for live viewing when the bandwidth is limited.
User Manual of Network Camera 56 A higher frame rate is advantageous when there is movement in the video stream, as it maintains image quality throu ghout. Max. Bitrate: Set the max . bitrate to 32~16384 Kbps. The hi gher value corresponds to th e higher video quality , but t he higher bandwidth is required.
User Manual of Network Camera 57 Or Configuration > Advanced Conf iguration > V ideo / Audio > Audio Figure 6-26 Audio Settings 2. Configure the following settings. Audio Encoding: G .722.1, G .71 1 ulaw , G .71 1alaw , G .726, and MP2 L2 are selectable.
User Manual of Network Camera 58 Figure 6-27 Region of Interest Setting s 2. Draw the region of interest on the image. There are f our r egions can be drawn. 3. Choose the stream t ype to set the ROI encoding. 4. Choose the ROI type. There are two options for ROI encoding, the fix ed reg ion encoding and the dynamic tracking.
User Manual of Network Camera 59 The d y namic region refers to the ROI defined b y int elligent anal ysis such as human face detection. Y o u can choose the Image Quality Enhancing level for the ROI encoding. 5. Click Save to save the settings. 6.
User Manual of Network Camera 60 sets of parameters for user to configure. Day/night Auto-s witch Figure 6-29 Display Settings of Day/night Auto-switch Image Adjust ment Brightness describes bright of the ima ge, which ranges from 1~100, a nd the default value is 50.
User Manual of Network Camera 61 is selec table, e.g.: T amron 2.8-8mm F1.2 ( M13VP288- IR ), or if DC lens is a dopted, then manual and auto are selectable. The exposure time refers to the electronic shu tter time , which r anges from 1 ~ 1/100,000s.
User Manual of Network Camera 62 T rigger ed by alarm inpu t: The switch is triggered by alarm input, and you ca n set the triggered mode to day or night. Smart IR gives user an option to turn ON / OFF the IR LED. Set the smart IR to ON , and Auto and M anual are s electable for IR mode.
User Manual of Network Camera 63 Mode and Expert Mode are selectable. Set the DNR level from 0~100, an d the default value is 50 in Normal Mode. Set the DNR level from both space DNR level [0~100] and time DNR level [0~100] in Expert Mode. Defog Mode : Y ou c an enable the defog function when the environment i s foggy and the image is misty .
User Manual of Network Camera 64 Figure 6-32 Day/Night Scheduled-Switch Configuration Interface S teps: 1. Click the time li ne to select the start tim e and the end time of the switch. 2. Click Common tab to configure the common parameters applicable to the day mode and night mode.
User Manual of Network Camera 65 Figure 6-33 OSD Settings 2. C heck the co rresponding checkbox to select th e displa y of cam era n ame, date or week if required. 3. Edit t he camera name in the text field of Camera Name . 4. S elect from the drop-down list to set the time format, date format, display mode and the OSD font size.
User Manual of Network Camera 66 Figure 6-35 Adjust OSD Location 7. C lick Save to activate the above settings. 6.5.3 Configuring T ext Overlay Settings Purpose: Y ou can customize the text overlay .
User Manual of Network Camera 67 2. C heck the checkbox in front of textbox to enable the on-screen display . 3. Input the characters in the textbox. 4. (Optional)Use the mouse to click and drag the r ed text frame in the live view window to adjust the text overlay position.
User Manual of Network Camera 68 5. Click S top Drawing to finish drawing or click Clear All to clear all of the areas you set without saving them. 6. Click Save to save the settings. 6.5.5 Configuring Pictur e Overlay Purpose: Picture overla y enables you to overlay a pictur e o n the ima ge.
User Manual of Network Camera 69 6.6 Configuring and Handling Alarms This section ex plains how to configure the netwo rk camera to r espond to a larm events, including motion detection, video tamperi.
User Manual of Network Camera 70 Configuration > Advanced Configuration> Events > Motion Detection (2)Check the checkbox of Enable Motion Detection. (3)Check the checkbox of Enable Dynamic Analysis for Motion if you want to mark the detected objects with green rectangle s.
User Manual of Network Camera 71 Figure 6-40 Arming T im e (1)Click Edit to edit the arming schedule. The Figure 6-34 shows the editing interface of the arming schedule. (2)Choose the day you want to set the arming schedule. (3)Click to set the time period for the arming schedule.
User Manual of Network Camera 72 3. Set the Alarm Actions for Motion Detection. Check the checkbox to select the linkage meth od. Notify su rveillance center , send email, upload to FTP , trigger channel and tri gger alarm output are selectable. Y ou can specify the linkage method when an event occurs.
User Manual of Network Camera 73 detailed information. T rigger Alar m Output Trigger one or more external alarm outputs when an event occurs. Note: T o trigger an ala rm output whe n a n e vent oc curs , please refer to Section 6.6.4 to set the related parameters.
User Manual of Network Camera 74 Day/Night Auto-Switch S teps: (1) Draw the detection area as in the normal configuration mode. Up to 8 areas are supported. (2) Select Auto-Switch for Switch Day and Night Settings . Figure 6-44 Day/Night Auto-Switch (3) Select the area by clicking the area No.
User Manual of Network Camera 75 Figure 6-45 Day/Night Scheduled-Switch (3) Select the start time and the end time for the switch timing. (4) Select the area by clicking the area No. (5) Slide the cursor to adjust the sensitivity and proportion of object on the area for the selected area in the daytime.
User Manual of Network Camera 76 Figure 6-46 V ideo T ampering Alarm 2. Check Enable V id eo T amper in g checkbox to enable the video tampering detection. 3. Set the video tampering area; re f er to T ask 1 Set the Motion De tection Area in Section 6.
User Manual of Network Camera 77 2. Choose the alarm input No. and the Alarm T ype. The alarm t ype can be NO (Normally Open) and NC (Normally Closed). Edit the name to set a name for the alarm input (optional). Figure 6-47 Alarm Input Settings 3. Click Edit to set the arming schedule for the alarm input.
User Manual of Network Camera 78 Configuration>Advanced Configuration> Events > Alarm Output 2. Select one alarm output channel in the Alarm Outpu t drop-down list. Y ou can also set a name for the alarm output (optional). 3. The Delay time can be set to 5sec, 10sec, 30sec, 1min, 2 min, 5min, 10min or Manual .
User Manual of Network Camera 79 S teps: 1. Enter the Exception Settings interface: Configuration > Advanced Configuration> Events > Exception 2. Check the checkbox to set the actions taken for the Exception alarm. Refe r to T ask 3 Set the Alarm Actions T aken for Motion Detection in Section 6.
User Manual of Network Camera 80 Figure 6-50 Face Detection Interface S teps: 1. Enter the face detection settings int erface: Configuration > Advanced Configuration > Events > Face Detection 2. Check the Enable Face Detection to checkbox to enable the function.
User Manual of Network Camera 81 5. Configure the linkage action for face detection. Note ： The face detection is only supported by a certain series of camera modes.
User Manual of Network Camera 82 Figure 6-51 Audio Exception Configuration 6.6.8 Configuring Line Crossing Detec ti on This function can be used for detecting people, vehicles and objects crossing a pre-defined area. The line crossing direction can be set as bidirectional, from left to right or from right to left.
User Manual of Network Camera 83 Figure 6-52 Draw Crossing Line And you can select the directions as A<->B, A ->B, and B- >A . A< ->B : Only the arrow on the B side shows; when an object going across the plane with both direction can be detected and alarms are triggered.
User Manual of Network Camera 84 Steps: 1. C heck the Enable Intrusion Detection checkbox. 2. C lick Draw Area , and then draw a rectangle on the image as a defense region. Note: when you draw the rectang le, all lines should connect end to end to each other.
User Manual of Network Camera 85 enabl ed . 1. C lick Edit to set the arming schedule. 2. C hoose to trigger alarm actions as Notify Surveillance Ce n ter , Send Email , Upload to FTP and Trigger Channel or trigger the Alarm Output . 3. C lick Save to save the settings.
User Manual of Network Camera 86 change of scene can trigger the alarm. Arming Schedule is configured to set the time you want the function to be enabled. 2. C lick Edit to set the arming schedule. 3. C hoose to trigger alarm actions as Notify Surveillance Ce n ter and Send Email , or trigger the Alarm Output .
User Manual of Network Camera 87 Figure 6-56 Behavior Analysis VCA Info Behavior Analysis V ersion: It lists the version of the algorithms library .
User Manual of Network Camera 88 1. C heck the checkbox of Camera Calibration to enable this function. 2. S elect the calibration mode as Input Basic Data or Dra w on Live V iew V ideo. Input Basic Data : Input the mounting h eight, viewing angle, and horizon ratio of the camera manually .
User Manual of Network Camera 89 1. C lick Shield Region tab to enter the shield region configuration interface. 2. C lick Draw Are a . Draw area by left click end-points in the live view window , and right click to finish the area drawing. Notes: ● Polygon area with up to 10 sides is supported.
User Manual of Network Camera 90 S teps: 1. C lick Rule T ab to enter the rule configuration interface. 2. C heck the checkbox of Rule to enable rules of behavior analysis. 3. S elect the rule type as None, Line Crossing, Intrusion, Region Entrance, and Region Exiting.
User Manual of Network Camera 91 Figure 6-59 Advanced Configuration Detection S ensitivity [0~4]: Refers to the s ensitivit y of the camera detects a tar get. The higher the v alue, the easier a target be reco gnized, and the higher t he misinformation is.
User Manual of Network Camera 92 2. S elect the Filter T ype a s Actual Siz e or Pixel. Actual Size : I nput the length a nd width of both the max imum si z e and the minimum size. Only the target size is between the min. size and max . si z e will trigger the alarm.
User Manual of Network Camera 93 Figure 6-60 Face Capture VCA Info Face Capture V ersion : It lists the version of the algorithms library . Display information includes the display on picture and display on stream.
User Manual of Network Camera 94 Rule S teps: 1. C heck the checkbox of Rule to enable rules of face ca ptur e. 2. C lick Minimize Pupil Distance to draw the minimum pupil distance. The distance of the drawn pupil will be displayed on the box below the live view .
User Manual of Network Camera 95 every frame. Captur e Sensitivity [0~20]: The threshold the camera tr eats the target as a face. Onl y wh en the face score generated by the algorithm is equal or hi gher than the value, the camera will treat the tar get as a face.
User Manual of Network Camera 96 6.7.3 Heat Map Heat map is a graphical representation of data represented by colors. The heat map function of the camer a usuall y be used to analyze the visit times and dwell time of customers in a configured area. Heat Map Configuration Steps: 1.
User Manual of Network Camera 97 Detection Sensitivity [0~100]: It refers to the sensitivity of the camera identify a tar get. The over- high s ensitivity may cause the misinformation. I t is recommended you set the sensitivity as the default value, which is 50.
User Manual of Network Camera 98 Figure 6-63 Space Heat Map Notes: As shown in the figur e above, red c olor block (255, 0, 0) indicates the most welcome area, and blue color block (0, 0, 255) indicates the less-popular area.
User Manual of Network Camera 99 Figure 6-64 People Counting Configuration 2. S elect People Counting Configuration tab to set the detailed parameters. 3. C heck the checkbox of Enable People Counting to enable the function. 4. C lick Draw Area to define the area you want to count the entered people and left people.
User Manual of Network Camera 100 Generation Speed (T ime) [0~100] : The speed of the head or should be treated as a tar get. If you set the value lower , the h ead or shoulder will not be recognized as a targ et in t he configured area if it is there from the start.
User Manual of Network Camera 101 1. C lick People Counting S tatistics to enter the data statistics interface. 2. S elect the report type by clicking the dropdown menu. Daily report, wee kl y report, monthly report, and annual report are selectable. 3.
User Manual of Network Camera 102 Chapter 7 S torage Sett ings Befor e you start: T o configure rec o rd settings, please make sure that you have the network storage device within the network or the SD card inserted in your ca mera.
User Manual of Network Camera 103 Please refer to the User Manual of NAS for creating the file path. (4) Click Save to add the network disk. 2. Initialize the added network disk.
User Manual of Network Camera 104 Figure 7-4 Quota Settings Notes: Up to 8 NAS disks can be connected to the camera. T o initialize and use the SD card after insert it to the ca me ra, please refer to the steps of NAS disk initialization.
User Manual of Network Camera 105 Figure 7-5 Recording Schedule I nterface 2. C heck the checkbox of Enable Record Schedule to enable scheduled recording. 3. S et the record para meters of the camera. Figure 7-6 Record Parameters Pre-record: The time you set to start r ecording before the scheduled time or the event.
User Manual of Network Camera 106 The Post-record time can be configured as 5 s, 10 s, 30 s, 1 min, 2 min, 5 min or 10 min. Not e: The record parameter configurations vary depending on the camera model. 4. C lick Edit to edit the record schedule. Figure 7-7 Record Schedule 5.
User Manual of Network Camera 107 If you select Continuous , the video will be recorded automatically according to the time of the schedule. Record T rigger ed by M otion Detection If you select Motion Detection , the video will be recorded when the motion is detected.
User Manual of Network Camera 108 Figure 7-8 Edit Record Schedule (3) Check the checkbox of Select All and click Copy to cop y settings of this day to the whole week. Y ou c an also check any of the checkboxes before the date and click Copy . (4) Click OK to save the settings and exit the Edit Record Schedule interface.
User Manual of Network Camera 109 Check the Enable E vent-trigger ed Snapshot checkbox to check event-triggered snapshot. 3. Select the quality of the snapshot. 4. Set the time interval between two snapshots. 5. Click Save to save the settings. Uploading to FTP Y ou can follow below configuration instructions to upload the snapshots to FTP .
User Manual of Network Camera 1 10 Figure 7-9 Snapshot Settings.
User Manual of Network Camera 111 Chapter 8 People Counting Compared with the people counting function supported by the iDS camera, the people counting of the non -iDS do not ne ed to confi gure the calibrations, and the parameter configuration is easier .
User Manual of Network Camera 1 12 6. C onfigure the Detection Sensitivity [0~100]. It refers to the sensitivity of the camera recognize a tar get . The hig h er the sensitivity , the easier the camera judges the head or shoulder as a tar get. It is recommended you set the sensitivity as the default value, which is 50.
User Manual of Network Camera 1 13 Figure 8-2 Statistics Result.
User Manual of Network Camera 1 14 Chapter 9 Playback Purpose: This section explains how to view the remotely recorded video files stored in the network disks or SD cards. S teps: 1. Click Playback on the menu bar to enter playback interface . Figure 9-1 Playback Interface 2.
User Manual of Network Camera 1 15 Figure 9-3 Playback T oolbar Table 9-1 Description of the buttons Button Operation Button Operation Play Capture a picture Pause / Star t/Stop clipping video files S.
User Manual of Network Camera 1 16 Chapter 10 Log Sear ching Purpose: The operation, alar m, exception and information of the c ame ra can be st ored in log files. Y ou can also export the log files on your demand. Befor e you start: Please configure network storage for th e camera or insert a SD card in the camera.
User Manual of Network Camera 117 Chapter 11 Others 11.1 Managing User Accounts Enter the User Management interface: Configuration >Basic Configuration> Security > User Or Configuration > Advanced Conf iguration> Sec u rity > User The admin user h as acc ess to create, modif y or delete other accounts.
User Manual of Network Camera 1 18 Figure 11-2 Add a User Modify a User S teps: 1. Left-click to select the user from the list and click Modif y . 2. Modi fy the User Na me , Level or Password . 3. In th e Basic Permission field and Camera Configuration field, you can check or uncheck the permissions.
User Manual of Network Camera 1 19 Figure 11-3 Modify a User Delete a User S teps: 1. C lick to select the user you want to delete and click Delete . 2. C lick OK on the pop-up dialogue box to delete the user . 11.2 Authentication Purpose: Y ou can specifically secure the stream data of live view .
User Manual of Network Camera 120 Note: If you disable the R TSP authentication, anyone can access the video stream by the R TSP protocol via the IP address. 3. Select the W eb Authentication as Basic or Di gest. Basic : The basic authentication method is adopted.
User Manual of Network Camera 121 Note: Only live view is available for the anonymous user . 11.4 IP Addr ess Fil ter Purpose: This function makes it possible for access control. S teps: 1. Enter the IP Address Filter interface: Configuration> Advanced Configuration> Security > IP Add r ess Filter Figure 11-7 IP Address Filter Interface 2.
User Manual of Network Camera 122 Figure 11-8 Add an IP (3) Click the OK to finish adding. Modify an IP Address S teps: (1) Left-click an IP address from filter list and click Modify . (2) Modify the IP address in the text filed. Figure 11-9 Modify an IP (3) Click the OK to finish modifying.
User Manual of Network Camera 123 2. C heck the checkbox of Enable T elnet to enable the remote login b y the telnet, and uncheck the checkbox to disable the telnet. 3. C heck the checkbox of Enable SSH to e nable the da ta communication security , and uncheck the checkbox to disable the SSH.
User Manual of Network Camera 124 11.7 Maintenance 11.7.1 Rebooting the Cam e ra S teps: 1. Enter the Maintenance interface: Configuration > Basic Configuration> System > Maintenance Or Configuration > Advanced Conf iguration> System > Maintenance: 2.
User Manual of Network Camera 125 Configuration file is used for the batch configuration of the camera, which can simplify the configuration steps when there are a l ot of cameras needing configuring.
User Manual of Network Camera 126 Figure 11-15 Remote Upgrade Note: The upgrading process will take 1 ~10 minutes. P lease don't disconnect power of the camera during th e process , and the camera reboots automatically after upgrade.
User Manual of Network Camera 127 11.9 RS -485 Settings Purpose: The RS-485 serial port is used to control the PTZ of the camera. The configuring of the PTZ parameters should be done before you control the PTZ unit.
User Manual of Network Camera 128 Appendix Appendix 1 SADP Softwar e Introdu cti on Description of SADP V 2.0 SADP (Search Active Devices Protocol) is a kind of user-friendly and installation-free online device search tool. I t searches the active o nline devices within y our subnet and displays the information of the devices.
User Manual of Network Camera 129 searched devices will be added to the list. Note: Y ou can c li ck or on each column heading to or der the information; you can click to expand the device table a nd hide the network parameter pa nel on the right side, or click to show the network parameter panel.
User Manual of Network Camera 130 Note: Serial code is a series of characters combined b y the start time and the serial number of the device. 2. Input the code in the Serial code field and c lick Confirm to restore the defa ult password.
User Manual of Network Camera 131 Appendix 2 Port Mapping The following settings are for TP-LINK router ( TL - W R641G). The settings vary depending on dif ferent m odels of routers. S teps: 1. S elect the W AN Connection T ype , as shown below: Figure A.
User Manual of Network Camera 132 another camera as 81, 8001, 555, 8201 with I P 19 2.168.1.24. Refer to the steps as below: S teps: 1. As the settings mention ed above, m ap the port 80, 8000, 554 and 8200 for the network camera at 192.168.1.23 2. Map the port 81, 8001, 5 55 and 8201 for the network camera at 192.
User Manual of Network Camera 133.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hikvision DS-2CD4065F-A è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hikvision DS-2CD4065F-A - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hikvision DS-2CD4065F-A imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hikvision DS-2CD4065F-A ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hikvision DS-2CD4065F-A, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hikvision DS-2CD4065F-A.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hikvision DS-2CD4065F-A. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hikvision DS-2CD4065F-A insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
