Manuale d’uso / di manutenzione del prodotto BW36 del fabbricante Heat & Glo LifeStyle
Vai alla pagina of 24
Heat-N-Glo, a Division of Hearth Technologies Inc. 20802 Kensington Blvd. Lakeville, MN 55044 BW36 BW36C W OODBURNING FIREPLA CE INST ALLA TION & OPERA TING INSTR UCTIONS FOR RESIDENTIAL USE Model BW36 shown.
4-00 2 30491D BW36 SERIES WOODBURNING FIREPLACE T able of Contents A. Listings and Code Approvals .................................................................................................... ...................... 3 B. Description of the Fireplace System .
The BW36 Series fireplace system has been tested and listed in accordance with the UL127 Standards, and has been listed by Underwriters Laboratories Inc. for installation and operation in the United States as described in these Installation & Operating Instructions.
HTI Catalog # Description BW36* Radiant Fireplace, includes integral grate and hearth protection strips BW36C* Heat Circulating Fireplace, includes integral grate and hearth protection strips HX3 Hear.
No one builds a better fire 17 5 / 8 " 9 3 / 8 " 4" 36" 11 1 / 2 " 5 / 8 " 33 5 / 8 " 21" 6" 7 1 / 4 " 10 7 / 8 " 21 7 / 8 " 18 3 / 4 ".
HTI CAT.# A SL315 15 ° SL330 30 ° HTI CAT.# A B SL306 6" 4 3 / 4 " SL312 12" 10 3 / 4 " SL318 18" 16 3 / 4 " SL324 24" 22 3 / 4 " SL336 36" 34 3 / 4 &quo.
23" 14 3 / 4 " 16 7 / 8 " 15 3 / 4 " 16 7 / 8 " 29 1 / 4 " 4-00 7 30491D CHIMNEY TERMINAL CAPS & VENT SECTIONS TR342 ROUND TERMINAL CAP TR344 ROUND TERMINAL CAP WITH .
WITH OUTSIDE AIR WITH OR WITHOUT OUTSIDE AIR WITHOUT OUTSIDE AIR 4-00 8 30491D Figure 1 Fireplace Locations Figure 2 Installation along a wall or an exterior chase. Figure 3 Corner Installation BW36 SERIES WOODBURNING FIREPLACE * A minimum of 1" air clearance must be maintained between the firebox and wall.
2" MIN. AIR SPACE CLEARANCE TO ENCLOSURE A POSITION MANTEL 12" ABOVE TOP OF FIREBOX OPENING. 19 3 / 4 " 33 5 / 8 " Figure 4 shows a typical framing (using 2 x 4 lumber) of the fireplace, assuming combustible materials are used. All required clearances to combustibles around the fireplace must be adhered to.
(THERMAL CONDUCTIVITY) "K" = BTU in./hr. ft 2 ° F TO SUBSTITUTE ALTERNATE INSULATION MATERIAL, YOU NEED TO KNOW THE "K" FACTOR FOR THAT MATERIAL. TO CALCULATE THE REQUIRED THICKNESS FOR THE ALTERNATE MATERIAL USE THE FOLLOWING FORMULA: K ALT.
4-00 11 30491D Figure 7 Sidewalls/Surrounds A combustible mantel may be positioned no lower than 12 ” above the top of the firebox opening. The combustible mantel may have a maximum depth of 12 ” .
4-00 12 BW36 SERIES WOODBURNING FIREPLACE W ARNING! DO NOT COMBINE OFFSETS TO CREATE AN OFFSET GREATER THAN 30 ° FROM VERTICAL. THIS MAY CREATE A FIRE HAZARD SINCE THE NATURAL DRAFT MAY BE RESTRICTED. A B 1 1 / 4 " OVERLAP Figure 8 Chimney Offset/Return e.
4-00 13 30491D BW36 SERIES WOODBURNING FIREPLACE No one builds a better fire Major building codes specify a minimum chimney height above the roof top. These specifications are summarized in what is known as the “ Ten Foot Rule ” .
4-00 14 30491D BW36 SERIES WOODBURNING FIREPLACE No one builds a better fire F . STEP-BY-STEP INST ALLA TION OF THE FIREPLA CE SYSTEM METAL STRIPS TWO INCHES UNDER EDGE OF FIREPLACE AND HEARTH EXTENSION 1" OVERLAP Figure 10 Positioning the Metal Strips W ARNING! BEFORE STARTING, DO THE FOLLOWING: 1.
4-00 15 30491D BW36 SERIES WOODBURNING FIREPLACE No one builds a better fire Figure 12 Connecting Chimney Sections Figure 11 Offset Secured to Fireplace STEP 5 - Preparing the Ceiling for Firestop Spacers.
4-00 16 30491D BW36 SERIES WOODBURNING FIREPLACE No one builds a better fire 24" AS8 ATTIC INSULATION SHIELD FS338 FIRESTOP SPACER CHIMNEY INSULATION 10 1 / 2 " 14 1 / 2 " Figure 14 Installing an AS8 Figure 16 Ceiling and Attic Construction STEP 10 - Marking the Exit Point of the Roof.
4-00 17 30491D BW36 SERIES WOODBURNING FIREPLACE No one builds a better fire Figure 17 Outside Air Location STEP 12 - Assembling the Chimney Sections. Continue to add chimney sections through the roof opening, maintaining at least a 2" air space.
4-00 18 30491D BW36 SERIES WOODBURNING FIREPLACE No one builds a better fire 1-1/2" clearance to combustibles Figure 18 Gas Knockout Location Figure 19 Positioning the Hearth Extension STEP 19 - Installing the Glass Doors.
4-00 19 30491D BW36 SERIES WOODBURNING FIREPLACE No one builds a better fire 1. Materials for the Chase. The chase is constructed using framing mate- rials much the same as the walls in your home. A variety of materials may be used including brick, stone, veneer brick, or stan- dard siding materials.
4-00 20 30491D BW36 SERIES WOODBURNING FIREPLACE No one builds a better fire TR342 TERMINAL CAP UPPERMOST CHIMNEY SECTION 18" MAX. DISTANCE CHASE TOP Figure 22 Installing a Terminal Cap H. OPERA TING INSTR UCTIONS NOTICE: SAVE AND PASS THESE OPERATING INSTRUCTIONS AND THE INSTALLATION INSTRUCTIONS TO SUBSEQUENT OWNERS.
4-00 21 30491D BW36 SERIES WOODBURNING FIREPLACE No one builds a better fire STARTING THE FIRE. Check the flue damper to be certain it is in the full open position. Place crumpled or twisted paper under the fireplace grate. Loosely arrange kindling or small pieces of wood to form a layer above the paper.
4-00 22 30491D BW36 SERIES WOODBURNING FIREPLACE No one builds a better fire W ARNING! FIREPLACES EQUIPPED WITH DOORS SHOULD BE OPERATED ONLY WITH DOORS FULLY OPEN OR FULLY CLOSED. IF DOORS ARE LEFT PARTIALLY OPEN, GAS AND FLAME MAY BE DRAWN OUT OF THE FIREPLACE OPENING, CREATING THE RISK OF BOTH FIRE AND SMOKE.
4-00 23 30491D BW36 SERIES WOODBURNING FIREPLACE No one builds a better fire CA UTION: WHEN LEFT CLOSED WHILE BURNING YOUR FIREPLACE, FIRE- SCREENS AND GLASS DOORS WILL BE HOT. HANDLE WITH CARE. OUTSIDE AIR . A damper control handle allows the individual control of the outside air inlets if your fire- place is equipped with this option.
4-00 24 30491 REV D W ARRANTY FOR HEA T -N-GLO FIREPLA CES The limited warranty will not become effective until you have mailed the completed warranty card to HEAT-N-GLO, A DIVISION OF HEARTH TECHNOLOGIES INC., 20802 Kensington Blvd., Lakeville, MN 55044.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Heat & Glo LifeStyle BW36 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Heat & Glo LifeStyle BW36 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Heat & Glo LifeStyle BW36 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Heat & Glo LifeStyle BW36 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Heat & Glo LifeStyle BW36, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Heat & Glo LifeStyle BW36.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Heat & Glo LifeStyle BW36. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Heat & Glo LifeStyle BW36 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
