Manuale d’uso / di manutenzione del prodotto LCOR-HVB-CE del fabbricante Heat & Glo
Vai alla pagina of 44
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 1 - Do not store or use gasoline or other flam- mable vapors and liquids in the vicinity of this or any other appliance. - What to do if you smell gas • Do not try to light any appliance.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 2 These units MUST use one of the flue systems described in the Installing the Fireplace section of the Installers Guide .
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 3 T able of Content s Safety and W arning Information .................................................. 2 Service Parts List ..................................................
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 4 * Part number list on following page. 5 Log Assembly Service Parts Diagram Service Parts List PIER-HVB-CE Beginning Manufac.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 5 (NG , LP) Exploded Part s Diagram IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When ordering, supply serial and model numbers to ensure correct service parts.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 6 Service Parts Diagram Service Parts ST -HVB-CE Beginning Manufacturing Date: 6-04 Ending Manufacturing Date: ______ * Part number list on following page.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 7 (NG , LP) Exploded Part s Diagram IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When ordering, supply serial and model numbers to ensure correct service parts.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 8 * Part number list on following page. 5 Log Assembly Service Parts Diagram Service Parts LCOR-HVB-CE Beginning M anufacturi.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 9 (NG , LP) Exploded Part s Diagram IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When ordering, supply serial and model numbers to ensure correct service parts.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 10 * Part number list on following page. 5 Log Assembly Service Parts Diagram Service Parts RCOR-HVB-CE Beginning M anufactur.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 11 (NG , LP) Exploded Part s Diagram IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When ordering, supply serial and model numbers to ensure correct service parts.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 12 V alve Assembly Service Parts Beginning M anufacturing Date: 6-04 Ending Manufacturing Date: ______ Standing Pilot V alve .
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 13 Appliance Certification The Heat & Glo fireplace models discussed in this Installers Guide have been tested to certification standards and listed by the applicable laboratories.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 14 Figure 1. Diagram of the PIER-HVB-CE REAR FLUE CO LLAR S EL ECT RI CA L ACCE S S GA S L I NE ACCE S S GA S CO NT RO LS &am.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 15 Figure 2. Diagram of the ST -HVB-CE RE AR FLUE COL LARS ELECTRIC AL ACCE SS GAS LINE ACCE SS GAS CO NTR OLS & LA BELS .
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 16 Figure 3. Diagram of the LCOR-HVB-CE and RCOR-HVB-CE 5-14 (1 33mm) 12 (3 06mm) 1/ 2 (13 mm) (4 ) 42-5 /8 (1 082mm ) 42 (1 .
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 17 3 Inst alling the Fireplace Step 1. Locating the Fireplace The diagram below shows space and clearance require- ments for locating a fireplace within a room. Minimum Clearances from the Fireplace to Combustible Materials Figure 4.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 18 Framing should be constructed of 51mm x 102mm (2” x 4”) lumber or heavier .
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 19 NOTE: PIPES OVERLAP 32mm (1-1/4”) A T EACH JOINT . Figure 6. DVP-Series Direct Flue Component Specifications (127mm (5”) inner pipe / 203mm (8”) outer pipe) D V P 9 0 S T 320 mm (12-9/16 in.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 20 Figure 7. Flue System Component s and T ermination Kits Step 3. Installing the Flue System A. Flue System Approvals These models are approved to use DVP series direct flue pipe components and terminations (see Figures 6 and 7).
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 21 Figure 8 STRAIGHT OUT HORIZONT A L FLUEING H Max. Run 610 mm (24 in.) Figure 9.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 22 Figure 1 1. Flueing with One 90° Elbow Figure 10. Flueing with One 90° Elbow V H H V NA TURAL GAS - FLUEING WITH ONE 90° ELBOW V (FT . ) H (FT .) 1' MIN. (305mm) 3' MAX.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 23 Figure 12. Flueing with T wo 90° Elbows H 1 H V V V 1 H NA TURAL GAS FLUEING WITH TWO 90° ELBOWS V (FT .) H + H 1 (FT .) 1' MIN. (305mm) 3' MAX. (914mm) 2' MIN.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 24 Figure 13. Flueing with T wo 90° Elbows Figure 14. Flueing with T wo 90° Elbows H 1 V H V H H 1 NA TURAL GAS FLUEING WITH TWO 90° ELBOWS V (FT .) H + H 1 (FT .) 1' MIN.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 25 Figure 15. Flueing with three 90° elbows H H 1 H 2 V H V H 1 V 1 NA TURAL GAS FLUEING WITH THREE 90° ELBOWS V + V 1 (FT .) H + H 1 + H 2 (FT . ) 1' MIN. (305mm) 3' MAX.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 26 Figure 16. Flueing with three 90° elbows V H H 1 V 1 V H H 1 V 1 NA TURAL GAS FLUEING WITH THREE 90° ELBOWS V + V 1 (FT .) H + H 1 (FT .) 1' MIN. (305mm) 3' MAX.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 27 1. Attach the First Flue Component to the Starting Collars T o attach the first flue component to the starting collars of the fireplace: • Slide the first flue section onto the unit and push in until they snap lock in position.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 28 4. Install Firestops For Horizontal Runs - Firestops are REQUIRED on both sides of a combustible wall through which the flue passes. NOTE: Model DVP-TRAP does not need an exterior firestop on an exterior combustible wall.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 29 Figure 22. Ceiling Firestop (Ceiling Side) If the area above the ceiling is NOT an attic, position and secure the ceiling firestop on the ceiling side of the previously cut and framed hole.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 30 For V ertical T erminations - T o locate the flue and install the flue sections: • Locate and mark the flue centerpoint on the underside of the roof, and drive a nail through the centerpoint.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 31 V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED Figure 26 V ent T ermination Minimum Clearances L = 2.1 M ...................... clearance above paved side- walk or a paved driveway lo- cated on public property M * = 50.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 32 Step 4. Positioning, Leveling, and Securing the Fireplace • Place the fireplace into position. • Level the fireplace from side to side and from front to back. • Shim the fireplace with non-combustible material, such as sheet met al, as necessary .
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 33 • Insert insulation from the outside of the fireplace and pack the insulation tightly to totally seal between the pipe and the outer casing.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 34 Step 9. Finishing Figure 30 shows the minimum vertical and corresponding maximum horizontal dimensions of fireplace mantels or other combustible projections above the top front edge of the fireplace.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 35 Inst alling the T rim Combustible materials may be brought up to the specified clearances on the side and top front edges of the fireplace, but MUST NEVER overlap onto the front face.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 36 LOG #1 (SRV2068-700): Place log #1 behind grate tabs on the second and third grate bars on the left rear corner . Position so that the bottom grooves fit over bars and the log is snug against the grate t abs.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 37 LOG #4 (SRV2068-703): Place log #4 in the right rear corner of the log grate using bottom grooves for placement. Align log #4 by using the grate corner and rear cross bar as stops.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 38 CAUTION: Logs are fragile. Carefully remove the logs from the packaging. Logs #4 and #5 are the same log.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 39 LOG #3 (SRV2068-702): Position log #3 across the first, second and third grate bars and pull towards the front against the grate tabs on bars one and three. 3 LOG #4 (SRV2068-703): Place log #4 in the left front corner of the log grate using bottom grooves for placement.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 40 LOG #6 (SRV582-705): Position log #6 on top of the groove in log #3 with the forked end resting on the grate assembly as shown.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 41 Placing the Ember Material Ember material is shipped with this gas fireplace. T o place the ember material: S tep 1 1. Before Lighting the Fireplace Before lighting the fireplace, be sure to do the following: ! Step 12.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 42 4 Maint aining and Servicing Y our Fireplace Fireplace Maintenance Although the frequency of your appliance servicing and .
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 43 5 T roubleshooting With proper installation, operation, and maintenance the gas fireplace will provide years of trouble-free service.
Heat & Glo • PIER/ST/L&RCOR-HVB-CE • 2068-900 Rev . H • 6/07 44 Sym pt om Po ssi b l e C ause Correct ive A cti on 4. Fr equ en t pil ot ou tage pr oblem . a. P i lot fl ame m ay be t oo h i gh or t oo low , or bl owin g (h igh ), cau sin g pi lot safet y t o drop ou t.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Heat & Glo LCOR-HVB-CE è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Heat & Glo LCOR-HVB-CE - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Heat & Glo LCOR-HVB-CE imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Heat & Glo LCOR-HVB-CE ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Heat & Glo LCOR-HVB-CE, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Heat & Glo LCOR-HVB-CE.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Heat & Glo LCOR-HVB-CE. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Heat & Glo LCOR-HVB-CE insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
