Manuale d’uso / di manutenzione del prodotto QV36B-A del fabbricante Hearth and Home Technologies
Vai alla pagina of 72
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 1 • DO NOT store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - DO NOT try to light any appliance.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 2 Not for use with solid fuel. ( Ne doit pas entre utilise avec un combustible solide). This appliance must be installed in a ccordance with local codes, if any; if not, follow ANSI Z 223.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 3 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury .
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 4 = Contains updated information. 13 Finishing A. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 52 B. Facing Material . . . . . . . . . . . . . . . . . . . .
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 5 B. Limited Lifetime W arranty 4021-645C 12-29-10 Page 1 of 2 Hearth & Home T echnologies Inc.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 6 4021-645C 12-29-10 Page 2 of 2 W ARRANTY CONDITIONS: 7KLVZDUUDQWRQOFRYHUV++7DSSOLDQFHVWKDWDUHSXUFKDVHG.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 7 B. T empered Glass Speci fi cations Hearth & Home T echnologies appliances manufactured with tempered glass may be installed in hazardous loca- tions such as bathtub enclosures as de fi ned by the Con- sumer Product Safety Commission (CPSC).
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 8 H. Requirements for the Commonwealth of Massachusetts For all side wall horizontally vented gas fueled equipment installed in every dwe.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 9 Figure 2.1 General Operating Parts B. Y our Fireplace W ARNING! DO NOT operate fi replace before read- ing and understanding operating instructions. Failure to operate fi replace according to operating instructions could cause fi re or injury .
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 10 D. Clear Space W ARNING! DO NOT place combustible objects in front of the fi replace or block louvers. High temperatures may start a fi re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 1 1 I. Lighting Instructions (Standing Pilot) 1. Turn of f all electric power to the appliance if ser- vice is to be performed. 2. Open control access panel. 3. Move switch to “OFF” position.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 12 J. After Fireplace is Lit Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • T urn the fi replace of f and allow it to completely cool.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 13 Glass Cleaning Frequency: Seasonally By: Homeowner T ools Needed : Protective gloves, glass cleaner , drop cloth and a stable work surface. CAUTION! Handle fi xed glass assembly with care.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 14 B. Maintenance T asks-Quali fi ed Service T echnician The following tasks must be performed by a quali fi ed ser- vice technician.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 15 A. T ypical Appliance System NOTICE: Illustrations and photos re fl ect typical installations and are for design purposes only . Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual Figure 4.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 16 B. Design and Installation Considerations Quadra-Fire direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 17 5 5 F raming and Clearances A. Selecting Appliance Location When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 18 C B D A B. Constructing the Appliance Chase A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should be enclosed inside the chase.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 19 D. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances as speci fi ed. Framing or fi nishing material closer than the minimums listed must be constructed entirely of noncom- bustible materials (i.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 20 A. V ent T ermination Minimum Clearances Roof Pitch H (Min.) Ft. Flat to 6/12...........................................................1.0* Over 6/12 to 7/12 ..........................
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 21 Figure 6.3 Minimum Clearances for T ermination O N P R Q X = AIR SUPPL Y INLET A = 12 inches................. clearances above grade, veranda, porch, deck or balcony B = 12 inches......
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 22 A. Approved Pipe This appliance is approved for use with Hearth & Home T echnologies DVP or SLP venting systems. Refer to Sec- tion 16B for vent component information. DO NOT mix pipe, fi ttings or joining methods from differ- ent manufacturers.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 23 E. Use of Flex V ent The fl ex vent must be supported with the spacing between support intervals not exceeding 4 feet, with no more than 1/2 inch sag between supports.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 24 F . V ent Diagrams Figure 7.4 Note: T here MUST b e a 25% reduc tion in total H w hen using fl ex vent exc ep t wh en using the si mple up and out installation (see Figure 5.3 ). Note: Use SL P Series components only .
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 25 Figure 7.5 T op V ent - Horizontal T ermination V enting with 2 elbows (NG) T op V ent - Horizontal T ermination V enting with 2 elbow.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 26 Figure 7.6 T op V ent - Horizontal T ermination V enting with 3 elbows (NG) T op V ent - Horizontal T ermination V enting with 3 elbow.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 27 T op V ent - V ertical T ermination No Elbow V 1 = 60 ft. Max. (18.3 m) Figure 7.8 INNER HEA T SHIELD T op V ent Application Rear V ent Application Note : Be sure to re- install the inner heat shield after exhaust restrictor installation.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 28 Figure 7.9 T op V ent - V ertical T ermination V enting with 2 elbows (NG) T op V ent - V ertical T ermination V enting with 2 elbows .
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 29 Figure 7.10 T op V ent - V ertical T ermination V enting with 3 elbows (NG) T op V ent - V ertical T ermination V enting with 3 elbows.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 30 V 1 H 1 V 2 V 3 H 2 T op V ent - V ertical T ermination - (continued) Four 90º Elbows V 1 Min. H 1 Max. V 2 Min. H 2 Max. V 3 Min. 1-1/2 ft. 457 mm 4 ft. 1.2 m 4 ft. 1.2 m 4 ft. 1.2 m 3-1/2 ft.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 31 Figure 7.12 H 1 = 24 in. (71 1 mm) Maximum Rear V ent - Horizontal T ermination No Elbows Rear V ent - Horizontal T ermination V enting with 2 elbows H 1 MAX. V 1 MIN. H 2 MAX. H 1 + H 2 MAX.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 32 Rear V ent - Horizontal T ermination V enting with 3 elbows H 1 MAX. V 1 MIN. H 1 + H 2 MAX. H 1 + H 2 + H 3 MAX. 1-1/2 ft. 457 mm Back to back elbows 1 ft. 305 mm 2-1/2 ft. 762 mm 3-1/2 ft.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 33 INST ALLED HORIZONT ALL Y H 1 H 2 V 2 Figure 7.16 Rear V ent - V ertical T ermination V enting with 2 elbows V 1 MIN. H 1 MAX. H 2 MAX. H 1 + H 2 MAX. Back to back elbows 1-1/2 ft. 457 mm 1 ft.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 34 Clearances to Combustibles: Refer to Section 5 for clearances to the appliance, man- tel, mantel legs and wall projection. Refer to Section 8 for pipe clearances to combustibles. T ermination Cap For installation of termination cap see minimum vent heights for various pitched roofs.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 35 EXISTING CHIMNEY HEARTH FLOOR EXISTING CHIMNEY EXHAUST AIR VENT PIPE INLET AIR VENT PIPE T o minimize cold air drafts, seal with non-combustible insulation.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 36 A. Pipe Clearances to Combustibles W ARNING! Risk of Fire! Maintain air space clearance to vent.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 37 C. Install the Ceiling Firestop A ceiling fi restop MUST be used between fl oors and attics. • DVP pipe only - Frame an opening 10 in. by 10 in. (254 mm by 254 mm) whenever the vent penetrates a ceiling/ fl oor (see Figure 8.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 38 D. Install Attic Insulation Shield W ARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home T echnologies Inc. requires the use of an attic shield.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 39 CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during installa- tion. Sheet metal edges are sharp. NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 40 B. Rear V ent NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time. NOTICE: Once the seal cap has been removed it CANNOT be reattached. Figure 9.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 41 C. Securing and Leveling the Appliance W ARNING! Risk of Fire! Prevent contact with: • Sagging or loose insulation • Insulation backing or plastic • Framing and other combustible materials Block openings into the chase to prevent entry of blown- in insulation.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 42 1 0 10 Inst alling V ent Pipe ( DVP and S LP Pi p e ) A. Assemble V ent Sections (DVP Pipe Only) Attach V ent to the Firebox Assembly Note: The end of the pipe sec tions wi t h the lanced tabs wi ll face toward the appliance.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 43 B. Assemble V ent Sections (SLP Pipe Only) T o attach the fi rst vent component to the starting collars of the appliance: • Lock the vent components into place by sliding the pipe section onto the collar .
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 44 120º Figure 10.8 Securing V ertical Pipe Sections 120º Figure 10.9 Securing Horizontal Pipe Sections E. Disassemble V ent Sections • Rotate either section (see Figure 10.10) so the seams on both pipe sections are aligned as shown in Figure 10.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 45 F . Install Decorative Ceiling Components (SLP only) A decorative ceiling thimble can be installed on a fl at ceil- ing through which the vent passes. The decorative ceiling thimble is used to cover the fi restop.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 46 G. Install Metal Roof Flashing • See minimum vent heights for various pitched roofs (Figure 10.14) to determine the length of pipe to extend through the roof. • Slide the roof fl ashing over the pipe sections extending through the roof as shown in Figure 10.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 47 SCREWS CAULK STORM COLLAR (1 of 3) Figure 10.18 Figure 10.18 TERMINA TION CAP I. Install V ertical T ermination Cap • Attach the ver.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 48 Figure 10.20 V enting through the wall INTERIOR HEA T SHIELD OR EXTENDED HEA T SHIELD W ALL SHIELD FIRESTOP HEA T SHIELD 1-1/2 IN.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 49 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a qualified service technician using Hearth & Home T echnologies speci fi ed and approved parts.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 50 B. Standing Pilot Ignition System Wiring • The standing pilot ignition system wiring does not require a 1 10 V AC supply to operate. See Figure 12.1. • A 1 10 V AC junction box MUST be installed for use with a fan or remote control.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 51 F . W all Switch Installation for Fan (Optional) If the box is being wired to a wall mounted switch for use with a fan (See Figure 12.3): • The power supply for the appliance must be brought into a switch box.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 52 A. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances as speci fi ed. Framing closer than the minimums list- ed must be constructed entirely of noncombustible materials (i.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 53 B. Facing Material • Metal front faces may be covered with non-combustible materials only . • Facing and/or fi nishing materials must not interfere with air fl ow through louvers, operation of louvers or doors, or access for service.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 54 A. Remove Fixed Glass Assembly See Section 14.G. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the fi rebox. C. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the fi rebox or underneath in the control cavity .
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 55 F . Install the Log Assembly If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately , refer to the following instructions.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 56 STEP 1: Carefully remove the logs from the packaging. CAUTION: Logs are fragile! 2016-925B 6/03 STEP 2: LOG #1 (SRV2016-701): Place notches of log #1 on outer two grate tines, and push against back of fi rebox.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 57 J. Install Hood The hood is shipped with the front/door . K. Air Shutter Setting Air shutter settings should be adjusted by a quali fi ed ser- vice technician at the time of installation.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 58 A. Standing Pilot Ignition System 1 5 15 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 59 T roubleshooting (continued) Symptom Possible Cause Corrective Action 3. (Continued) C. V alve. T urn the valve knob to the ON position. Place the ON/ OFF switch in the ON position. T ake a reading with a millivolt meter at the thermopile terminals.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 60 1 6 16 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5. Figure 16.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 61 B. V ent Components Diagrams Figure 16.2 DVP vent components Pipe Effective Length Inches Millimeters DVP4 4 102 DVP6 6 152 DVP12 12 3.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 62 DVP-TRAP1 DVP-TRAP2 DVP-TRAPK2 DVP-TRAPK1 DVP-TRAP Horizontal T ermination Cap 15-1/8 in. (384 mm) 12 in. (305 mm) 8 in. (203 mm) Max Effective Length Note: Heat shields MUST overlap by a minimum of 1-1/2 in.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 63 13-1/4 in. (367 mm) 24-5/8 in. (625 mm) 27-1/2 in. (127 mm) RF6M Roof Flashing Multi-pak 31 in. (787 mm) 24-5/8 in. (625 mm) 13-1/4 in. (367 mm) RF12M Roof Flashing Multi-pak BEK Trap Ca p Brick Extension 13-3/4 in.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 64 B. V ent Components Diagrams (continued) Figure 16.5 SLP Series V ent Components 8-3/4 in. 222 mm 6-1/2 in. 165 mm 6-5/8 in. 168 mm 6 in. 152 mm 6-1/2 in. 165 mm 6-5/8 in. 168 mm 9-7/8 in.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 65 B. V ent Components Diagrams (continued) Figure 16.6 SLP Series V ent Components SLP-SNKD Snorkel T ermination Cap SLP-TVHW V ertical .
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 66 Figure 16.7 Coaxial to Colinear V ent Components LINK-DV30B Flex Liner Kit DV -46DV A-GCL Coaxial/Colinear Appliance Connector COAXIAL to COLINEAR VENTING B.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 67 C. Service Parts QV32B-A Beginning Manufacturing Date: June 2003 Ending Manufacturing Date: ______ R 32” Direct V ent Gas Fireplace IMPORT ANT : THIS IS DA TED INFORMA TION.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 68 IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer .
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 69 #12 Burner/V alve Assembly Part number list on following page. 12.1 12.8 12.7 12.6 12.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 70 C. Service Parts IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer .
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 71 Service Parts QV32B-A, QV36B-A IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer .
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 72 Quadra-Fire, a brand of Hearth & Home T echnologies Inc. 7571 215 th Street West, Lakeville, MN 55044 www .quadra fi re.com D. Contact Information Please contact your Quadra-Fire dealer with any questions or concerns.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hearth and Home Technologies QV36B-A è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hearth and Home Technologies QV36B-A - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hearth and Home Technologies QV36B-A imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hearth and Home Technologies QV36B-A ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hearth and Home Technologies QV36B-A, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hearth and Home Technologies QV36B-A.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hearth and Home Technologies QV36B-A. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hearth and Home Technologies QV36B-A insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
