Manuale d’uso / di manutenzione del prodotto 800 del fabbricante Hearth and Home Technologies
Vai alla pagina of 20
MODEL 800 NOV A FREEST ANDING PELLET STOVE INST ALLA TION, OPERA TION, AND MAINTENANCE INSTRUCTIONS CONGRA TULA TIONS— Yo u are now the proud owner of one of the finest stoves in the world for your home—the QUADRA- FIRE! Now before installing your stove and building your first fire, record the serial number on the warranty card.
NOTES Page 2.
T ABLE OF CONTENTS Page Safety Label ................................................................................................................... ........................................... 4 Listing and Specifications .........................
SAFETY LABEL (FOUND ON BACK W ALL OF HOPPER) Page 4.
LISTINGS AND SPECIFICA TIONS QUADRA-FIRE 800 NOV A pellet stoves are safety tested and listed with W arnock Hersey International to ASTME 1509 and ULCS627. Also suitable for mobile home installation (see page 11 for details). HEA T INPUT*: 28,000 to 37,500 BTU per hour P AR TICULA TE EMISSIONS PER HOUR: 0.
FLOOR PROTECTION MINIMUM CLEARANCES TO COMBUSTIBLE MA TERIALS The floor protector must be noncombustible material, extending beneath heater and to the front, sides, and rear as indicated below . NOTE: In a corner installation, the floor protection must follow the above clearances.
Page 7.
Page 8.
Page 9.
T OP VENT FLUE ADAPTER INST ALLA TION INSTRUCTIONS 3"-3" ADAPTER #81 1-0450 3"-6" COLLAR #812-2690 1 ) Put a layer of silicone on the 3" (76mm) exhaust outlet. 2 ) Slide the flue adapter onto the rear exhaust outlet. 3 ) Adjust the assembly to a vertical position.
MOBILE HOME INST ALLA TION OUTSIDE AIR KIT FOR 800 NOV A: P ART #81 1-0420 (FLOOR) OR P AR T #81 1-0430 (REAR) 1 An outside air inlet must be provided for the combustion air and be unrestricted while the stove is in use. 2. The stove must be secured to the mobile home by bolting it to the floor (using lag bolts).
OPERA TING INSTRUCTIONS 1. FUEL SIZE AND MA TERIAL Fuel pellets are made from sawdust or wood byproducts. If the source material is hardwood, they will have a higher mineral content, creating a heavier ash. Minerals and other noncombustible materials, such as sand, will turn into glass when heated to the extreme temperatures our firepot reaches.
Page 13.
Page 14 ( N ) COMBUSTION BLOWER ( WHITE ).
1. FIREPOT A. It takes very little time to clean the firepot. W e recommend that you clean the firepot at least once a week. However , if the fuel you are burning has a high dirt content, it will be necessary to clean the firepot more often. Dirty fuel will cause clinkers to form in the firepot.
1. POWER SUPPL Y A. Check the wall receptacle for 120 volt, 60 Hz (standard current). Make sure the outlet is grounded and has the correct polarity . 2. FUSE A. The fuse is located on the left side, next to the restart button and the indicator light. However , to access the fuse, you must remove the left side panel.
9. THERMOCOUPLE A. The thermocouple is located on top of the firepot inside the ceramic protection tube. Remove the ceramic tube and inspect the thermocouple for deterioration or breakage. B. Check the terminal block screws to see if they are tight and making a good electrical connection (located on the top of the lower junction box).
1. PLUG IN STOVE, NO RESPONSE A. Check the power supply for 120 volts AC. B. Check the fuse in the junction box (7 amp, 120 volt fuse AGC-7). C. Check snap disc #3 (unplug stove before checking). Push reset on snap disc #3. D. Control box (consult your dealer).
8. THERMOST A T WILL NOT ST ART UNIT A. Check the power to the stove. 1. Unplug for 10 seconds and then plug in. The exhaust blower should come on. If it does, go to B. B. The thermostat or the thermostat wiring maybe faulty . 1. Disconnect the thermostat wires from the terminal block located on the back of the stove.
Aladdin Hearth Products, warrants their pellet heating appliances to the original purchaser for the lifetime of the appliance, to be free from defects in material and workmanship. This warranty gives you specific legal rights; you may have other rights which may vary from state to state.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hearth and Home Technologies 800 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hearth and Home Technologies 800 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hearth and Home Technologies 800 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hearth and Home Technologies 800 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hearth and Home Technologies 800, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hearth and Home Technologies 800.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hearth and Home Technologies 800. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hearth and Home Technologies 800 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
