Manuale d’uso / di manutenzione del prodotto 100M del fabbricante Hawking
Vai alla pagina of 25
1.
FCC Warning This equipment has been tested and found to comply with the lim its for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limitations are designed to provide reasonable prot ection against harmful interference in a residen tial installation.
Unpacking the Switch 4 Introduction 1.1 General Description 5 1.2 Gigabit Ethernet Technology 5 1.3 Features 6 1.4 Front Panel 6 1.5 Rear Panel 7 Installation 2.1 Desktop Installation 8 2.2 Rack-Mount Installation 8 2.3 Installing Network Cables 9 2.4 Network Application 9 Description of Functions 3.
The complete HGS16S package consists of: • One HGS16S 16-Port 10/100/1000M Web-Smart Switch • Rack mount kit: 2 mounting brackets and screws • Four rubber feet with adhesive backing • One AC p.
1.1 General Description The device is a 16-port 10/100/1000Mbps Ethernet Web-Smart Switch. Compared with traditional 10/100Mbps Ethernet, the switch de livers a dedicated Gigabit connection to every attached client with no congestion issues.
1.3 Key Features • 16 fixed 10/100/1000Mbps Gigabit Ethernet ports • Provides Auto-discovery Function for easy network management • Provides 4K MAC address entries • 16 groups VLAN table • S.
Wiring for 10/100/1000Mbps (Copper) Below is the summary of the cabling required: Media Speed Wiring 10Mbps Category 3,4,5 UTP/STP 100Mbps Category 5 UTP/STP 10/100/1000Mbps copper 1000Mbps Category 5.
This switch can be placed directly on your desktop, on the floor, or mounted in a rack. Users can immediately use most of the features simply by attaching the cables and turning the power on. 2.1 Desktop Installation For desktop installation, the switch needs to be put on a clean, flat desk or table close to a power outlet.
2.3 Installing Network Cables Station Connections Refer to the wiring statement of the previous section; connect each station/device to the switch with the correct cables. Switch-to-Switch Connections In making a switch-to-switch connection, using every po rt to connect another switch or backbone is stro ngly recommended.
3.1 PHY Monitoring and Port Mode Setup One of the software’s major tasks is to continuously monito r the PHYs in order to set up t he switch ports according to whether the link is up or down, and in the latter case, what the current speed, duplex mode and pause capabilities are.
This section instructs you on how to enter and set up the c onfigurations, whi ch can be accessed by RS-232 serial port (out-of-band) on the rear panel or by Telnet sessi on / Internet Browser over the network (in-band). Factory Default value: IP: 192.
In-Band Connections (Web Browser / Telnet) To manage the switch through in-band access, you should co nfigure the managem ent station with an IP address and subnet mask compatible with your switch. 1. Run your Web Browser and enter the IP address “192.
4.2 Homepage On the Home page, you can select what you would like to config ure by clicking the menu tabs located at the top of the homepage. They include: • System • Ports • VLANS • Aggregati.
To restore the default values of switch, click the “ Default ” button at the top of the homepage. If you want to reboot the switch, click the “ Reboot ” Button. To check the connection status of each port, from 1 to 16, take a look at the port monitor.
4.2.1 System To set up the system configurations such as login values, time-out values, and for enabling the VLAN Management: Items Functions Mac Address The Mac Address of the switch S/W Version To look up the Software Version, see here. H/W Version The Hardware version Inactivity Timeout (Secs) Set the console inactivity timeout in seconds.
Note: After you change the IP address, the switch will reboot itself. You may click the new address to link the New IP Address with your browser. 4.2.2 Ports On this page, you can view the port status, set up the speed “Mode” and enable the “FDX Flow Control”.
Items Functions Link Shows the status of each port. When it is red, it means the connection is down. Otherwise, it is green. Mode Choose the Speed mode of port: 10/100/1000, Half/Full. To disable the port, choose “Disable”. If you set to auto-speed, it will be auto- negotiation.
PVID When the VLAN-enabled switch receives a ta gged packet, the packet will be sent to the port’s default VLAN according to the PVID (port VLAN ID) of the receiving port. Items Functions Port Port Number 1~16 PVID Port VLAN ID Aware To enable the PVID checking and inserting of one port, select “AWARE” Only Tagged Block the untagged frame.
19.
4.2.4 Aggregation/Trunking Configuration To set up the Port trunk groups, put the port numbers into the same Aggregation group line . There are eight groups that can be made. Do not forget to click the “Apply” to save th e settings. The m aximum number of ports for one group is 8.
4.2.5 QoS There is one mode of Quality of Service to choose: custom TOS. 4.2.5.1 Custom ToS To improve the network performance by applying the TOS, set up the priority of eight groups of precedence bits on this page. There are two types to choose, high or Low.
4.2.6 Mirror Port mirror is used to mirror traffic from a source port to a target port for analysis. Only 2 ports can be monitored (mirrored) simultaneously to 1 Monito r port (target port).
4.2.7 Statistics To check the status of port traffic, click the “Statistic” tab. You can click the “ Clear ” button to erase all records or click “ Refresh ” to show the most current status.
4.2.9 Default To restore to default values, 1. Click the default button on the homepage. 2. Click “Yes” to restore default values. Do not power off the switch while it is working. 4.2.10 Reboot To reboot the switch, 1. Click the “Reboot” button on the homepage 2.
Standard IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX IEEE802.3x full-duplex operation and flow control IEEE802.3ab 1000BASE-T IEEE802.1Q VLAN interoperability IEEE802.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hawking 100M è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hawking 100M - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hawking 100M imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hawking 100M ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hawking 100M, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hawking 100M.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hawking 100M. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hawking 100M insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
