Manuale d’uso / di manutenzione del prodotto Kwik-Kit KK-100-05 del fabbricante Havis-Shields
Vai alla pagina of 22
INSTALL INSTRUCTIONS KK-100-05 & KK-120-05 KWIK-KIT PRISONER TRANSPORT INSERT FORD and CHEVY VAN PR ISONER TRANSPORT TOOLS REQUIRED: ¼” & 3/8” Ratcheting Wrenches ¼” & 3/8”Air Ra.
KK-XXX-05_INST_8-07 2 40” COMPARTMENT (cont): QTY DESCRIPTION PART # USED FOR: 40 #10 x 1” Phillips pan head sheet metal screw GSM33196 Floor, wall to ceiling 25 #8 x 3/8” Phillips flat head scr.
Rear OEM Trim modifications 1997-2007 Chevrolet G-Series Van Installation of Kwik Kit is very similar in Ford and Chevy Vans. All kits start with a measurement at th e rear floor. The rear plastic floor trim on Chevy vans must be cut straight across as shown in phot o.
KK-XXX-05_INST_8-07 4 Ford Van Driver-Side rear Ford Van Passenger-Side rear PASSENGER WINDOW VAN PREPARATIONS: 1. Remove all rear bench seats from the vehicle. 2. Modify / remove interior parts as needed. 3. Remove floor mat/carpet and replace with ½” plywood or sound deadening m aterial.
KK-XXX-05_INST_8-07 5 1. Remove clear shrink- wrap covering the prisoner transport assembly. 2. This is the rear 40/60/or 80 section of the kit. 3. Remove all black hardware, wood panels and brackets holding wood panels. 4. Remove bolts holding the kit to the wood pallet.
KK-XXX-05_INST_8-07 6 Remove all black hardw are from asse mbled unit. This will give you the subassemblies as they are shown on the follow ing pages..
KK-XXX-05_INST_8-07 7 The following photos are the main subassemb lies as they are shipped from the factory. Remove drawing on final page and referen ce the item #’s as you install this kit.
KK-XXX-05_INST_8-07 8 Item #12 Rear bulkhead/door assembly Item #6 3 r d Compartment Bulkhead/door assembly Item #11 3 rd Compartment ceiling KWIK KIT LAYOUT Diamond plate floor and ceiling sections are not shown for detail purposes.
KK-XXX-05_INST_8-07 9 VERY IMPORTANT: Be sure that all Auxiliary lighting, video systems, Kwik kit options, and wiring are complete. Access is s ever ely limited after kit is installed. For neatness of wiring, route all cables down driver-s ide “B” pillar.
KK-XXX-05_INST_8-07 10 Place Driver-side Bench/Wall assembly into van so bench rests on wheel well Item #1 Remove steel support bracket for Emergency Exit Hatch pin.
Item #4 & #13 Place (2) Diamond Plate Floors between Bench/Wall assemblies and Front bulkhead . Place cardboard along side of bench while positioning Be careful that exposed wires are not touching metal and optional KK- x-VAK hoses are not completely crushed Note: Vent hose will be tight in spot s.
KK-XXX-05_INST_8-07 12 Remove screws holding the center divider together where 3 rd Compartment Bulkhead will be mounted. Item #5 Position 3 rd Compartment Ceiling into vehicle. Item #12 Current view of installa tion Slide the ceiling sections out of the way in order to access A/C hoses, wires, etc.
Re-install screws removed in step above and loosely attach aligning all three materials. Note: An awe or scribe is recommended to help align holes Item #9 to #5 Place 3 rd compartment bench Photo shows optional storage door Note: Be careful not to scratch bulkheads.
KK-XXX-05_INST_8-07 14 Loosely bolt Rear Bulkhead Doorframe ( at the door hinge) to Bench/Wall assemblies using ¼” x ¾” carriage bolts, washers and serrated nuts Item #6 to #2 Place the 3 rd Compartment Doorframe assembly .
KK-XXX-05_INST_8-07 15 An awe or scribe will help align the holes THE FOLLOWING STEPS AR E EXTREMLY CRITI CAL FOR A SUCCESFULL INSTALLATION! PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY.
KK-XXX-05_INST_8-07 16 Top Passenger-Side rear Top Driver-Side rear 3” Item #6 With unit positioned acc ording to m easurements on previous page, pre - drill and attach a #10 x 1” sheet metal screw to hold the rear Bulkhead in place while assembling the remainder of the unit.
Begin to tighten ALL loose hardware on the remainder of the unit, being sure to align edges and bends of materials being tightened. This will square the unit to itself.
KK-XXX-05_INST_8-07 18 3/8” x 2” Hex head bolt, washers, and nut On the Rear doorframe , remove the sheet metal screws installed e arlier. Drill 3/8” holes through the doorframe, floor, and vehicle. Attach using 3/8” x 2” hex head bolts, washers, fender washers, lock washers, and hex nuts.
Socket Ball Item #14 to doors and frames Attach Ball & Socket Style Doorstop. 1 st Attach “Ball” portion of assembly. Attach to threaded hole on the doo r using a ¼” x 1” Hex head bolt. nd 2 Attach the “Socket” and brack et portion. Attach to doorframe using #8 x ¾” Phillips machine screws and keps nuts.
KK-XXX-05_INST_8-07 20 Optional Storage Compartm ent (Sold Seperatley) FINAL INSTALLATION PHOTOS Optional Storage Compartm ent (Sold Separately).
KK-XXX-05_INST_8-07 21 PT-VIDEO-X C-VS-1800-ECO w/ C-TCB-7 & C-3090-7 K K -RLL KK-PV ENT K R -CCL-1 KR-DL PRISONER TRANSPORT OPTIONS – (A ll SOLD SEPERATLEY ).
Item 3 Item 7 Item 1 Item 12 Item 5 Item 8 ITEM DESCRIPTION 1 Driver-side Bench/Wall 2 Passenger-side Bench/Wall 3 Front Bulkhead 4 Diamond-plate Floor 5 Divider 6 Rear Bulkhead/ Doorframe 7 Driver-si.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Havis-Shields Kwik-Kit KK-100-05 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Havis-Shields Kwik-Kit KK-100-05 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Havis-Shields Kwik-Kit KK-100-05 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Havis-Shields Kwik-Kit KK-100-05 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Havis-Shields Kwik-Kit KK-100-05, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Havis-Shields Kwik-Kit KK-100-05.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Havis-Shields Kwik-Kit KK-100-05. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Havis-Shields Kwik-Kit KK-100-05 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
