Manuale d’uso / di manutenzione del prodotto KK-100-06 del fabbricante Havis-Shields
Vai alla pagina of 22
INSTALL INSTRUCTIONS KK-100-06 & KK-120-06 KWIK-KIT PRISONER TRANSPORT INSERT FORD and CHEVY VAN PR ISONER TRANSPORT TOOLS REQUIRED: ¼” & 3/8” Ratcheting Wrenches ¼” & 3/8”Air Ra.
KK-XXX-06_INST_8-07 2 40” COMPARTMENT (cont): QTY DESCRIPTION PART # USED FOR: 40 #10 x 1” Phillips pan head sheet metal screw GSM33196 Floor, wall to ceiling 25 #8 x 3/8” Phillips flat head scr.
KK-XXX-06_INST_8-07 3 Rear OEM Trim modifications 1997-2 007 Chevrolet G-Series Van Installation of Kwik Kit is very similar in Ford and Chevy Vans. All kits start with a measurement at th e rear floor. The rear plastic floor trim on Chevy vans must be cut straight across as shown in phot o.
KK-XXX-06_INST_8-07 4 Ford Driver-Side rear Ford Passenger-Side rear 8”inches 8” inches Note: Photos above show a Chevrolet Van. Photos ar e intended to show rubber floor mat option only. ***Kwik kits are designed for cargo vans with no rear OEM trim, however they can be installed into passenger window vans.
KK-XXX-06_INST_8-07 5 1. Remove clear shrink- wrap covering the prisoner transport assembly. 2. This is the rear 40/60/or 80 section of the kit. 3. Remove all black hardware, wood panels and brackets holding wood panels. 4. Remove bolts holding the kit to the wood pallet.
KK-XXX-06_INST_8-07 6 Remove all black hardw are from asse mbled unit. This will give you the subassemblies as they are shown on the follow ing pages..
KK-XXX-06_INST_8-07 7 The following photos are the main subassemb lies as they are shipped from the factory. Remove drawing on final page and referen ce the item #’s as you install this kit.
KK-XXX-06_INST_8-07 8 KWIK KIT LAYOUT Diamond plate floor and ceiling sections are not shown for detail purposes. 3 rd Compartment ceiling Item #12 Rear bulkhead/door assembly Item #6 3 r d Compartmen.
KK-XXX-06_INST_8-07 9 VERY IMPORTANT: Be sure that all Auxiliary lighting, video systems, Kwik kit options, and wiring are complete. Access is s ever ely limited after kit is installed. If optional rear load light(s) (KK-RLL) was ordered, install at this time.
KK-XXX-06_INST_8-07 10 Place Driver-side Bench/Wall assembly into van so bench rests on wheel well Item #1 Remove steel support bracket for Emergency Exit Hatch pin.
KK-XXX-06_INST_8-07 11 Current view of installa tion Place Center Divider into vehicle. Item #5 Item #4 Item #3 Approximate center Item #5 Carefully place Driver-side Ceiling section into vehicle. Item #7 Loosely bolt Center Divider to Front Bulkhead Item #5 to #3 Place (2) Diamond Plate Floors between Bench/Wall assemblies and Front bulkhead .
KK-XXX-06_INST_8-07 12 Remove screws holding the center divider together where 3 rd Compartment Bulkhead will be mounted. Item #5 Position 3 rd Compartment Ceiling into vehicle. Item #12 Current view of installa tion Slide the ceiling sections out of the way in order to access A/C hoses, wires, etc.
Place 3 rd compartment bench Photo shows optional storage door Note: Be careful not to scratch bulkheads. Item #10 Item #10 to #9 Bolt 3 rd Compartment Bench to 3 rd Compartment Divider using ¼” x ¾” carriage bolts and serrated nuts.
KK-XXX-06_INST_8-07 14 Item #6 to #5 Item #6 Item #6 Place Rear Bulkhead Doorframe into vehicle Position between Driver and Passenger-side Bench/Wall assemblies Loosely attach Doorframe to Center divider using #10 x 3/8” flat head machine screws and nylock nuts Item #6 to #2 Place the 3 rd Compartment Doorframe assembly .
KK-XXX-06_INST_8-07 15 An awe or scribe will help align the holes THE FOLLOWING STEPS AR E EXTREMLY CRITI CAL FOR A SUCCESFULL INSTALLATION! PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY.
KK-XXX-06_INST_8-07 16 Top Passenger-Side rear Top Driver-Side rear Item #6 Approximately 3”inches Item #6 3” inches Item #7 to #1 Item #6 Item #6 Position Driver-side Ceiling section to mate with Bench/Wall assem bly. Pre- drill 5/32” holes into Ceiling, using Bench/Wall assembly holes as a guide.
Begin to tighten ALL loose hardware on the remainder of the unit, being sure to align edges and bends of materials being tightened. This will square the unit to itself.
KK-XXX-06_INST_8-07 18 3/8” x 2” Hex head bolt, washers, and nut On the Rear doorframe , remove the sheet metal screws installed e arlier. Drill 3/8” holes through the doorframe, floor, and vehicle. Attach using 3/8” x 2” hex head bolts, washers, fender washers, lock washers, and hex nuts.
KK-XXX-06_INST_8-07 19 Socket Ball Item #14 to doors and frames Attach Ball & Socket Style Doorstop. 1 st Attach “Ball” portion of assembly. Attach to threaded hole on the doo r using a ¼” x 1” Hex head bolt. nd 2 Attach the “Socket” and brack et portion.
KK-XXX-06_INST_8-07 20 Optional Storage Compartm ent (Sold Seperatley) FINAL INSTALLATION PHOTOS Optional Storage Compartm ent (Sold Separately).
KK-XXX-06_INST_8-07 21 PT-VIDEO-X C-VS-1800-ECO w/ C-TCB-7 & C-3090-7 K K -RLL KK-PV ENT K R -CCL-1 KR-DL PRISONER TRANSPORT OPTIONS – (A ll SOLD SEPERATLEY ).
Item 3 Item 7 Item 12 Item 1 Item 8 Item 10 Item 6 Item 2 Item 4 Item 9 Item 11 Item 14 Item 15 Item 5 Item 14 Item 13 ITEM DESCRIPTION 1 Driver-side Bench/Wall 2 Passenger-side Bench/Wall 3 Front Bul.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Havis-Shields KK-100-06 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Havis-Shields KK-100-06 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Havis-Shields KK-100-06 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Havis-Shields KK-100-06 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Havis-Shields KK-100-06, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Havis-Shields KK-100-06.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Havis-Shields KK-100-06. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Havis-Shields KK-100-06 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
