Manuale d’uso / di manutenzione del prodotto FR2 Series del fabbricante Hatco
Vai alla pagina of 16
HYDRO-HEA TER Food Rethermalizers/Hot Food T able Heater FR2 Series Inst allation & Operating Manual I&W #07.05.143.00 This manual contains import ant safety information concerning the maintenance, use and operation of this product. Failure to follow the instructions contained in this manual may result in serious injury .
i INTRODUCTION Hatco FR2 Hydro-Heater Food Rethermalizers/Hot Food T able Heaters are designed to supply temperature-controlled water to a holding vessel (sink or tank) located above the heater .
CAUTIONS W ater in the unit and holding vessel is very hot. Wear protective gloves and proper attire when operating to avoid injury . Do not use extension pipes on the inlet and outlet connections on heater unit s. Poor performance or unsafe conditions may occur .
MODEL DESCRIPTIONS 2 ALL MODELS The Hydro-Heater mounts easily to the underside of a holding vessel, leaving the entire vessel area free. Units are shipped ready to inst all with all gaskets and fittings. Hydro-Heaters include a stainless steel front, powder coated body , a low- water cut-off system and a convenient drain outlet.
SPECIFICA TIONS 3 Form No. FR2M-0604 Kilowatt s Wire Sizing Fuse or Model V olt age (kW) Phase Amp s A WG* † Circuit Breaker* Shipping Weight FR2-3 208 3 1 14.5 12 20 24 lbs. (1 1 kg) FR2-4 208 4 1 19.2 12 30 24 lbs. (1 1 kg) FR2-6 208 6 1 28.8 10 40 27 lbs.
SPECIFICA TIONS 4 Form No. FR2M-0604 DIMENSIONS A C B ELECTRICAL Install a fused disconnect switch or circuit breaker sized according to the applicable Electrical Rating Chart . The wiring from the switch or circuit breaker to the Hatco unit must be in accordance with local electrical requirements and codes.
INST ALLA TION 5 Form No. FR2M-0604 PLUMBING An adhesive backed paper template is shipped with the unit and is used to locate the sink strainer holes. Use the following procedure to install the heater unit to the holding vessel.
INST ALLA TION 6 Form No. FR2M-0604 CAUTION W ater Quality Requirement s - Incoming water in excess of 3.0 grains of hardness per gallon (GPG) (.75 grains of hardness per liter) must be treated or sof tened before being supplied to a Hydro-Heater . W ater cont aining over 3.
OPERA TION 7 W ARNINGS Hatco FR2 series unit s are designed for commercial use only by properly trained personnel! W ARNINGS Unit s are designed to heat water up to 190ºF (88ºC). T o avoid any injury or damage DO NOT set temperature controls to a setting higher than 190ºF (88ºC).
OPERA TION 8 Form No. FR2M-0604 W ater T emp. At St art-Up T emperature °F (°C) Water Heated T o: W ater T emp. At St art-Up T emperature °F (°C) Water Heated T o: MINUTES TO HEA T T ABLE 9" .
MAINTENANCE 9 GENERAL W ARNING T o avoid any injury , turn the power switch off at the fuse disconnect switch/circuit breaker or unplug the unit from the power source and allow to cool completely before performing any maintenance or cleaning. Recommended Cleaning Schedule Complete draining and cleaning should be done • On a daily basis.
MAINTENANCE 10 Form No. FR2M-0604 WEEKL Y (See Figure 8) 1. T urn power switch to the OFF position. 2. Drain holding vessel to discharge visible water and debris. 3. Wipe visible deposits from the sink or t ank. 4. Remove clean-out caps (2- or 3-element unit s only).
MAINTENANCE 11 Form No. FR2M-0604 6. After cleaning, drain all expended solution from the unit through the sump drain. 7. Thoroughly wash heater tank with fresh water for several minutes until discharge is clear and all deliming solution has been removed and rinsed.
12 Form No. FR2M-0604 HA TCO LIMITED W ARRANTY 1. PRODUCT W ARRANTY Hatco warrants the product s that it manufactures (the “Products”) to be free from defect s in materials and workmanship, under .
13 Form No. FR2M-0604 NOTES.
HA TCO CORPORA TION P .O. Box 340500, Milwaukee, WI 53234-0500 U.S.A. (800) 558-0607 (414) 671-6350 Parts & Service Fax (800) 690-2966 Int’l. Fax (414) 671-3976 www .hatcocorp.com HA TCO AUTHORIZED P ARTS DISTRIBUTORS Printed in U.S.A. June 2004 ALABAMA Jones McLeod Appl.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hatco FR2 Series è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hatco FR2 Series - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hatco FR2 Series imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hatco FR2 Series ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hatco FR2 Series, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hatco FR2 Series.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hatco FR2 Series. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hatco FR2 Series insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
